Mercurial > pub > halpp

comparison f103c8/Inc/stm32f1xx_hal_conf.h @ 2:0c59e7a7782a

Find changesets by keywords (author, files, the commit message), revision number or hash, or revset expression.
Working on GPIO and RCC
author cin
date Mon, 16 Jan 2017 11:04:47 +0300
parents
children
comparison
equal deleted inserted replaced
1:a0b14b11ad9f 2:0c59e7a7782a
1 /**
2 ******************************************************************************
3 * @file stm32f1xx_hal_conf.h
4 * @brief HAL configuration file.
5 ******************************************************************************
6 * @attention
7 *
8 * <h2><center>&copy; COPYRIGHT(c) 2017 STMicroelectronics</center></h2>
9 *
10 * Redistribution and use in source and binary forms, with or without modification,
11 * are permitted provided that the following conditions are met:
12 * 1. Redistributions of source code must retain the above copyright notice,
13 * this list of conditions and the following disclaimer.
14 * 2. Redistributions in binary form must reproduce the above copyright notice,
15 * this list of conditions and the following disclaimer in the documentation
16 * and/or other materials provided with the distribution.
17 * 3. Neither the name of STMicroelectronics nor the names of its contributors
18 * may be used to endorse or promote products derived from this software
19 * without specific prior written permission.
20 *
21 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
22 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
23 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
24 * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
25 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
26 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
27 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
28 * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
29 * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
30 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
31 *
32 ******************************************************************************
33 */
34
35 /* Define to prevent recursive inclusion -------------------------------------*/
36 #ifndef __STM32F1xx_HAL_CONF_H
37 #define __STM32F1xx_HAL_CONF_H
38
39 #ifdef __cplusplus
40 extern "C" {
41 #endif
42
43 #include "main.h"
44 /* Exported types ------------------------------------------------------------*/
45 /* Exported constants --------------------------------------------------------*/
46
47 /* ########################## Module Selection ############################## */
48 /**
49 * @brief This is the list of modules to be used in the HAL driver
50 */
51 #define HAL_MODULE_ENABLED
52 /*#define HAL_ADC_MODULE_ENABLED */
53 /*#define HAL_CAN_MODULE_ENABLED */
54 /*#define HAL_CEC_MODULE_ENABLED */
55 /*#define HAL_CORTEX_MODULE_ENABLED */
56 /*#define HAL_CRC_MODULE_ENABLED */
57 /*#define HAL_DAC_MODULE_ENABLED */
58 /*#define HAL_DMA_MODULE_ENABLED */
59 /*#define HAL_ETH_MODULE_ENABLED */
60 /*#define HAL_FLASH_MODULE_ENABLED */
61 #define HAL_GPIO_MODULE_ENABLED
62 /*#define HAL_I2C_MODULE_ENABLED */
63 /*#define HAL_I2S_MODULE_ENABLED */
64 /*#define HAL_IRDA_MODULE_ENABLED */
65 /*#define HAL_IWDG_MODULE_ENABLED */
66 /*#define HAL_NOR_MODULE_ENABLED */
67 /*#define HAL_NAND_MODULE_ENABLED */
68 /*#define HAL_PCCARD_MODULE_ENABLED */
69 /*#define HAL_PCD_MODULE_ENABLED */
70 /*#define HAL_HCD_MODULE_ENABLED */
71 /*#define HAL_PWR_MODULE_ENABLED */
72 /*#define HAL_RCC_MODULE_ENABLED */
73 /*#define HAL_RTC_MODULE_ENABLED */
74 /*#define HAL_SD_MODULE_ENABLED */
75 /*#define HAL_SDRAM_MODULE_ENABLED */
76 /*#define HAL_SMARTCARD_MODULE_ENABLED */
77 /*#define HAL_SPI_MODULE_ENABLED */
78 /*#define HAL_SRAM_MODULE_ENABLED */
79 #define HAL_TIM_MODULE_ENABLED
80 /*#define HAL_UART_MODULE_ENABLED */
81 /*#define HAL_USART_MODULE_ENABLED */
82 /*#define HAL_WWDG_MODULE_ENABLED */
83
84 #define HAL_CORTEX_MODULE_ENABLED
85 #define HAL_DMA_MODULE_ENABLED
86 #define HAL_FLASH_MODULE_ENABLED
87 #define HAL_GPIO_MODULE_ENABLED
88 #define HAL_PWR_MODULE_ENABLED
89 #define HAL_RCC_MODULE_ENABLED
90
91 /* ########################## Oscillator Values adaptation ####################*/
92 /**
93 * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
94 * This value is used by the RCC HAL module to compute the system frequency
95 * (when HSE is used as system clock source, directly or through the PLL).
96 */
97 #if !defined (HSE_VALUE)
98 #define HSE_VALUE ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */
99 #endif /* HSE_VALUE */
100
101 #if !defined (HSE_STARTUP_TIMEOUT)
102 #define HSE_STARTUP_TIMEOUT ((uint32_t)100) /*!< Time out for HSE start up, in ms */
103 #endif /* HSE_STARTUP_TIMEOUT */
104
105 /**
106 * @brief Internal High Speed oscillator (HSI) value.
107 * This value is used by the RCC HAL module to compute the system frequency
108 * (when HSI is used as system clock source, directly or through the PLL).
109 */
110 #if !defined (HSI_VALUE)
111 #define HSI_VALUE ((uint32_t)8000000) /*!< Value of the Internal oscillator in Hz*/
112 #endif /* HSI_VALUE */
113
114 /**
115 * @brief External Low Speed oscillator (LSE) value.
116 * This value is used by the UART, RTC HAL module to compute the system frequency
117 */
118 #if !defined (LSE_VALUE)
119 #define LSE_VALUE ((uint32_t)32768) /*!< Value of the External oscillator in Hz*/
120 #endif /* LSE_VALUE */
121
122 #if !defined (LSE_STARTUP_TIMEOUT)
123 #define LSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for LSE start up, in ms */
124 #endif /* LSE_STARTUP_TIMEOUT */
125
126 /* Tip: To avoid modifying this file each time you need to use different HSE,
127 === you can define the HSE value in your toolchain compiler preprocessor. */
128
129 /* ########################### System Configuration ######################### */
130 /**
131 * @brief This is the HAL system configuration section
132 */
133 #define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */
134 #define TICK_INT_PRIORITY ((uint32_t)0) /*!< tick interrupt priority (lowest by default) */
135 #define USE_RTOS 0
136 #define PREFETCH_ENABLE 1
137
138 /* ########################## Assert Selection ############################## */
139 /**
140 * @brief Uncomment the line below to expanse the "assert_param" macro in the
141 * HAL drivers code
142 */
143 /* #define USE_FULL_ASSERT 1 */
144
145 /* ################## Ethernet peripheral configuration ##################### */
146
147 /* Section 1 : Ethernet peripheral configuration */
148
149 /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
150 #define MAC_ADDR0 2
151 #define MAC_ADDR1 0
152 #define MAC_ADDR2 0
153 #define MAC_ADDR3 0
154 #define MAC_ADDR4 0
155 #define MAC_ADDR5 0
156
157 /* Definition of the Ethernet driver buffers size and count */
158 #define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */
159 #define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */
160 #define ETH_RXBUFNB ((uint32_t)8) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */
161 #define ETH_TXBUFNB ((uint32_t)4) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */
162
163 /* Section 2: PHY configuration section */
164
165 /* DP83848_PHY_ADDRESS Address*/
166 #define DP83848_PHY_ADDRESS 0x01U
167 /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
168 #define PHY_RESET_DELAY ((uint32_t)0x000000FF)
169 /* PHY Configuration delay */
170 #define PHY_CONFIG_DELAY ((uint32_t)0x00000FFF)
171
172 #define PHY_READ_TO ((uint32_t)0x0000FFFF)
173 #define PHY_WRITE_TO ((uint32_t)0x0000FFFF)
174
175 /* Section 3: Common PHY Registers */
176
177 #define PHY_BCR ((uint16_t)0x00) /*!< Transceiver Basic Control Register */
178 #define PHY_BSR ((uint16_t)0x01) /*!< Transceiver Basic Status Register */
179
180 #define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */
181 #define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */
182 #define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */
183 #define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */
184 #define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */
185 #define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */
186 #define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */
187 #define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */
188 #define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */
189 #define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */
190
191 #define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */
192 #define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */
193 #define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */
194
195 /* Section 4: Extended PHY Registers */
196 #define PHY_SR ((uint16_t)0x10U) /*!< PHY status register Offset */
197
198 #define PHY_SPEED_STATUS ((uint16_t)0x0002U) /*!< PHY Speed mask */
199 #define PHY_DUPLEX_STATUS ((uint16_t)0x0004U) /*!< PHY Duplex mask */
200
201 /* Includes ------------------------------------------------------------------*/
202 /**
203 * @brief Include module's header file
204 */
205
206 #ifdef HAL_RCC_MODULE_ENABLED
207 #include "stm32f1xx_hal_rcc.h"
208 #endif /* HAL_RCC_MODULE_ENABLED */
209
210 #ifdef HAL_GPIO_MODULE_ENABLED
211 #include "stm32f1xx_hal_gpio.h"
212 #endif /* HAL_GPIO_MODULE_ENABLED */
213
214 #ifdef HAL_DMA_MODULE_ENABLED
215 #include "stm32f1xx_hal_dma.h"
216 #endif /* HAL_DMA_MODULE_ENABLED */
217
218 #ifdef HAL_ETH_MODULE_ENABLED
219 #include "stm32f1xx_hal_eth.h"
220 #endif /* HAL_ETH_MODULE_ENABLED */
221
222 #ifdef HAL_CAN_MODULE_ENABLED
223 #include "stm32f1xx_hal_can.h"
224 #endif /* HAL_CAN_MODULE_ENABLED */
225
226 #ifdef HAL_CEC_MODULE_ENABLED
227 #include "stm32f1xx_hal_cec.h"
228 #endif /* HAL_CEC_MODULE_ENABLED */
229
230 #ifdef HAL_CORTEX_MODULE_ENABLED
231 #include "stm32f1xx_hal_cortex.h"
232 #endif /* HAL_CORTEX_MODULE_ENABLED */
233
234 #ifdef HAL_ADC_MODULE_ENABLED
235 #include "stm32f1xx_hal_adc.h"
236 #endif /* HAL_ADC_MODULE_ENABLED */
237
238 #ifdef HAL_CRC_MODULE_ENABLED
239 #include "stm32f1xx_hal_crc.h"
240 #endif /* HAL_CRC_MODULE_ENABLED */
241
242 #ifdef HAL_DAC_MODULE_ENABLED
243 #include "stm32f1xx_hal_dac.h"
244 #endif /* HAL_DAC_MODULE_ENABLED */
245
246 #ifdef HAL_FLASH_MODULE_ENABLED
247 #include "stm32f1xx_hal_flash.h"
248 #endif /* HAL_FLASH_MODULE_ENABLED */
249
250 #ifdef HAL_SRAM_MODULE_ENABLED
251 #include "stm32f1xx_hal_sram.h"
252 #endif /* HAL_SRAM_MODULE_ENABLED */
253
254 #ifdef HAL_NOR_MODULE_ENABLED
255 #include "stm32f1xx_hal_nor.h"
256 #endif /* HAL_NOR_MODULE_ENABLED */
257
258 #ifdef HAL_I2C_MODULE_ENABLED
259 #include "stm32f1xx_hal_i2c.h"
260 #endif /* HAL_I2C_MODULE_ENABLED */
261
262 #ifdef HAL_I2S_MODULE_ENABLED
263 #include "stm32f1xx_hal_i2s.h"
264 #endif /* HAL_I2S_MODULE_ENABLED */
265
266 #ifdef HAL_IWDG_MODULE_ENABLED
267 #include "stm32f1xx_hal_iwdg.h"
268 #endif /* HAL_IWDG_MODULE_ENABLED */
269
270 #ifdef HAL_PWR_MODULE_ENABLED
271 #include "stm32f1xx_hal_pwr.h"
272 #endif /* HAL_PWR_MODULE_ENABLED */
273
274 #ifdef HAL_RTC_MODULE_ENABLED
275 #include "stm32f1xx_hal_rtc.h"
276 #endif /* HAL_RTC_MODULE_ENABLED */
277
278 #ifdef HAL_PCCARD_MODULE_ENABLED
279 #include "stm32f1xx_hal_pccard.h"
280 #endif /* HAL_PCCARD_MODULE_ENABLED */
281
282 #ifdef HAL_SD_MODULE_ENABLED
283 #include "stm32f1xx_hal_sd.h"
284 #endif /* HAL_SD_MODULE_ENABLED */
285
286 #ifdef HAL_NAND_MODULE_ENABLED
287 #include "stm32f1xx_hal_nand.h"
288 #endif /* HAL_NAND_MODULE_ENABLED */
289
290 #ifdef HAL_SPI_MODULE_ENABLED
291 #include "stm32f1xx_hal_spi.h"
292 #endif /* HAL_SPI_MODULE_ENABLED */
293
294 #ifdef HAL_TIM_MODULE_ENABLED
295 #include "stm32f1xx_hal_tim.h"
296 #endif /* HAL_TIM_MODULE_ENABLED */
297
298 #ifdef HAL_UART_MODULE_ENABLED
299 #include "stm32f1xx_hal_uart.h"
300 #endif /* HAL_UART_MODULE_ENABLED */
301
302 #ifdef HAL_USART_MODULE_ENABLED
303 #include "stm32f1xx_hal_usart.h"
304 #endif /* HAL_USART_MODULE_ENABLED */
305
306 #ifdef HAL_IRDA_MODULE_ENABLED
307 #include "stm32f1xx_hal_irda.h"
308 #endif /* HAL_IRDA_MODULE_ENABLED */
309
310 #ifdef HAL_SMARTCARD_MODULE_ENABLED
311 #include "stm32f1xx_hal_smartcard.h"
312 #endif /* HAL_SMARTCARD_MODULE_ENABLED */
313
314 #ifdef HAL_WWDG_MODULE_ENABLED
315 #include "stm32f1xx_hal_wwdg.h"
316 #endif /* HAL_WWDG_MODULE_ENABLED */
317
318 #ifdef HAL_PCD_MODULE_ENABLED
319 #include "stm32f1xx_hal_pcd.h"
320 #endif /* HAL_PCD_MODULE_ENABLED */
321
322 #ifdef HAL_HCD_MODULE_ENABLED
323 #include "stm32f1xx_hal_hcd.h"
324 #endif /* HAL_HCD_MODULE_ENABLED */
325
326
327 /* Exported macro ------------------------------------------------------------*/
328 #ifdef USE_FULL_ASSERT
329 /**
330 * @brief The assert_param macro is used for function's parameters check.
331 * @param expr: If expr is false, it calls assert_failed function
332 * which reports the name of the source file and the source
333 * line number of the call that failed.
334 * If expr is true, it returns no value.
335 * @retval None
336 */
337 #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__))
338 /* Exported functions ------------------------------------------------------- */
339 void assert_failed(uint8_t* file, uint32_t line);
340 #else
341 #define assert_param(expr) ((void)0)
342 #endif /* USE_FULL_ASSERT */
343
344 #ifdef __cplusplus
345 }
346 #endif
347
348 #endif /* __STM32F1xx_HAL_CONF_H */
349
350 /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/