Mercurial > pub > halpp
diff f103c8/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_rcc.h @ 2:0c59e7a7782a
Working on GPIO and RCC
| author | cin |
|---|---|
| date | Mon, 16 Jan 2017 11:04:47 +0300 |
| parents | |
| children |
line wrap: on
line diff
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/f103c8/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_rcc.h Mon Jan 16 11:04:47 2017 +0300 @@ -0,0 +1,1395 @@ +/** + ****************************************************************************** + * @file stm32f1xx_hal_rcc.h + * @author MCD Application Team + * @version V1.0.4 + * @date 29-April-2016 + * @brief Header file of RCC HAL module. + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2016 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F1xx_HAL_RCC_H +#define __STM32F1xx_HAL_RCC_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f1xx_hal_def.h" + +/** @addtogroup STM32F1xx_HAL_Driver + * @{ + */ + +/** @addtogroup RCC + * @{ + */ + +/** @addtogroup RCC_Private_Constants + * @{ + */ + +/** @defgroup RCC_Timeout RCC Timeout + * @{ + */ + +/* Disable Backup domain write protection state change timeout */ +#define RCC_DBP_TIMEOUT_VALUE ((uint32_t)100) /* 100 ms */ +/* LSE state change timeout */ +#define RCC_LSE_TIMEOUT_VALUE LSE_STARTUP_TIMEOUT +#define CLOCKSWITCH_TIMEOUT_VALUE ((uint32_t)5000) /* 5 s */ +#define HSE_TIMEOUT_VALUE HSE_STARTUP_TIMEOUT +#define HSI_TIMEOUT_VALUE ((uint32_t)2) /* 2 ms (minimum Tick + 1) */ +#define LSI_TIMEOUT_VALUE ((uint32_t)2) /* 2 ms (minimum Tick + 1) */ +#define PLL_TIMEOUT_VALUE ((uint32_t)2) /* 2 ms (minimum Tick + 1) */ +#define LSI_VALUE ((uint32_t)40000) /* 40kHz */ +/** + * @} + */ + +/** @defgroup RCC_Register_Offset Register offsets + * @{ + */ +#define RCC_OFFSET (RCC_BASE - PERIPH_BASE) +#define RCC_CR_OFFSET 0x00 +#define RCC_CFGR_OFFSET 0x04 +#define RCC_CIR_OFFSET 0x08 +#define RCC_BDCR_OFFSET 0x20 +#define RCC_CSR_OFFSET 0x24 + +/** + * @} + */ + +/** @defgroup RCC_BitAddress_AliasRegion BitAddress AliasRegion + * @brief RCC registers bit address in the alias region + * @{ + */ +#define RCC_CR_OFFSET_BB (RCC_OFFSET + RCC_CR_OFFSET) +#define RCC_CFGR_OFFSET_BB (RCC_OFFSET + RCC_CFGR_OFFSET) +#define RCC_CIR_OFFSET_BB (RCC_OFFSET + RCC_CIR_OFFSET) +#define RCC_BDCR_OFFSET_BB (RCC_OFFSET + RCC_BDCR_OFFSET) +#define RCC_CSR_OFFSET_BB (RCC_OFFSET + RCC_CSR_OFFSET) + +/* --- CR Register ---*/ +/* Alias word address of HSION bit */ +#define RCC_HSION_BIT_NUMBER POSITION_VAL(RCC_CR_HSION) +#define RCC_CR_HSION_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_CR_OFFSET_BB * 32) + (RCC_HSION_BIT_NUMBER * 4))) +/* Alias word address of HSEON bit */ +#define RCC_HSEON_BIT_NUMBER POSITION_VAL(RCC_CR_HSEON) +#define RCC_CR_HSEON_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_CR_OFFSET_BB * 32) + (RCC_HSEON_BIT_NUMBER * 4))) +/* Alias word address of CSSON bit */ +#define RCC_CSSON_BIT_NUMBER POSITION_VAL(RCC_CR_CSSON) +#define RCC_CR_CSSON_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_CR_OFFSET_BB * 32) + (RCC_CSSON_BIT_NUMBER * 4))) +/* Alias word address of PLLON bit */ +#define RCC_PLLON_BIT_NUMBER POSITION_VAL(RCC_CR_PLLON) +#define RCC_CR_PLLON_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_CR_OFFSET_BB * 32) + (RCC_PLLON_BIT_NUMBER * 4))) + +/* --- CSR Register ---*/ +/* Alias word address of LSION bit */ +#define RCC_LSION_BIT_NUMBER POSITION_VAL(RCC_CSR_LSION) +#define RCC_CSR_LSION_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_CSR_OFFSET_BB * 32) + (RCC_LSION_BIT_NUMBER * 4))) + +/* Alias word address of RMVF bit */ +#define RCC_RMVF_BIT_NUMBER POSITION_VAL(RCC_CSR_RMVF) +#define RCC_CSR_RMVF_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_CSR_OFFSET_BB * 32) + (RCC_RMVF_BIT_NUMBER * 4))) + +/* --- BDCR Registers ---*/ +/* Alias word address of LSEON bit */ +#define RCC_LSEON_BIT_NUMBER POSITION_VAL(RCC_BDCR_LSEON) +#define RCC_BDCR_LSEON_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_BDCR_OFFSET_BB * 32) + (RCC_LSEON_BIT_NUMBER * 4))) + +/* Alias word address of LSEON bit */ +#define RCC_LSEBYP_BIT_NUMBER POSITION_VAL(RCC_BDCR_LSEBYP) +#define RCC_BDCR_LSEBYP_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_BDCR_OFFSET_BB * 32) + (RCC_LSEBYP_BIT_NUMBER * 4))) + +/* Alias word address of RTCEN bit */ +#define RCC_RTCEN_BIT_NUMBER POSITION_VAL(RCC_BDCR_RTCEN) +#define RCC_BDCR_RTCEN_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_BDCR_OFFSET_BB * 32) + (RCC_RTCEN_BIT_NUMBER * 4))) + +/* Alias word address of BDRST bit */ +#define RCC_BDRST_BIT_NUMBER POSITION_VAL(RCC_BDCR_BDRST) +#define RCC_BDCR_BDRST_BB ((uint32_t)(PERIPH_BB_BASE + (RCC_BDCR_OFFSET_BB * 32) + (RCC_BDRST_BIT_NUMBER * 4))) + +/** + * @} + */ + +/* CR register byte 2 (Bits[23:16]) base address */ +#define RCC_CR_BYTE2_ADDRESS ((uint32_t)(RCC_BASE + RCC_CR_OFFSET + 0x02)) + +/* CIR register byte 1 (Bits[15:8]) base address */ +#define RCC_CIR_BYTE1_ADDRESS ((uint32_t)(RCC_BASE + RCC_CIR_OFFSET + 0x01)) + +/* CIR register byte 2 (Bits[23:16]) base address */ +#define RCC_CIR_BYTE2_ADDRESS ((uint32_t)(RCC_BASE + RCC_CIR_OFFSET + 0x02)) + +/* Defines used for Flags */ +#define CR_REG_INDEX ((uint8_t)1) +#define BDCR_REG_INDEX ((uint8_t)2) +#define CSR_REG_INDEX ((uint8_t)3) + +#define RCC_FLAG_MASK ((uint8_t)0x1F) + +/** + * @} + */ + +/** @addtogroup RCC_Private_Macros + * @{ + */ +/** @defgroup RCC_Alias_For_Legacy Alias define maintained for legacy + * @{ + */ +#define __HAL_RCC_SYSCFG_CLK_DISABLE __HAL_RCC_AFIO_CLK_DISABLE +#define __HAL_RCC_SYSCFG_CLK_ENABLE __HAL_RCC_AFIO_CLK_ENABLE +#define __HAL_RCC_SYSCFG_FORCE_RESET __HAL_RCC_AFIO_FORCE_RESET +#define __HAL_RCC_SYSCFG_RELEASE_RESET __HAL_RCC_AFIO_RELEASE_RESET +/** + * @} + */ + +#define IS_RCC_PLLSOURCE(__SOURCE__) (((__SOURCE__) == RCC_PLLSOURCE_HSI_DIV2) || \ + ((__SOURCE__) == RCC_PLLSOURCE_HSE)) +#define IS_RCC_OSCILLATORTYPE(__OSCILLATOR__) (((__OSCILLATOR__) == RCC_OSCILLATORTYPE_NONE) || \ + (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_HSE) == RCC_OSCILLATORTYPE_HSE) || \ + (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_HSI) == RCC_OSCILLATORTYPE_HSI) || \ + (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_LSI) == RCC_OSCILLATORTYPE_LSI) || \ + (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_LSE) == RCC_OSCILLATORTYPE_LSE)) +#define IS_RCC_HSE(__HSE__) (((__HSE__) == RCC_HSE_OFF) || ((__HSE__) == RCC_HSE_ON) || \ + ((__HSE__) == RCC_HSE_BYPASS)) +#define IS_RCC_LSE(__LSE__) (((__LSE__) == RCC_LSE_OFF) || ((__LSE__) == RCC_LSE_ON) || \ + ((__LSE__) == RCC_LSE_BYPASS)) +#define IS_RCC_HSI(__HSI__) (((__HSI__) == RCC_HSI_OFF) || ((__HSI__) == RCC_HSI_ON)) +#define IS_RCC_CALIBRATION_VALUE(__VALUE__) ((__VALUE__) <= 0x1F) +#define IS_RCC_LSI(__LSI__) (((__LSI__) == RCC_LSI_OFF) || ((__LSI__) == RCC_LSI_ON)) +#define IS_RCC_PLL(__PLL__) (((__PLL__) == RCC_PLL_NONE) || ((__PLL__) == RCC_PLL_OFF) || \ + ((__PLL__) == RCC_PLL_ON)) + +#define IS_RCC_CLOCKTYPE(CLK) ((((CLK) & RCC_CLOCKTYPE_SYSCLK) == RCC_CLOCKTYPE_SYSCLK) || \ + (((CLK) & RCC_CLOCKTYPE_HCLK) == RCC_CLOCKTYPE_HCLK) || \ + (((CLK) & RCC_CLOCKTYPE_PCLK1) == RCC_CLOCKTYPE_PCLK1) || \ + (((CLK) & RCC_CLOCKTYPE_PCLK2) == RCC_CLOCKTYPE_PCLK2)) +#define IS_RCC_SYSCLKSOURCE(__SOURCE__) (((__SOURCE__) == RCC_SYSCLKSOURCE_HSI) || \ + ((__SOURCE__) == RCC_SYSCLKSOURCE_HSE) || \ + ((__SOURCE__) == RCC_SYSCLKSOURCE_PLLCLK)) +#define IS_RCC_SYSCLKSOURCE_STATUS(__SOURCE__) (((__SOURCE__) == RCC_SYSCLKSOURCE_STATUS_HSI) || \ + ((__SOURCE__) == RCC_SYSCLKSOURCE_STATUS_HSE) || \ + ((__SOURCE__) == RCC_SYSCLKSOURCE_STATUS_PLLCLK)) +#define IS_RCC_HCLK(__HCLK__) (((__HCLK__) == RCC_SYSCLK_DIV1) || ((__HCLK__) == RCC_SYSCLK_DIV2) || \ + ((__HCLK__) == RCC_SYSCLK_DIV4) || ((__HCLK__) == RCC_SYSCLK_DIV8) || \ + ((__HCLK__) == RCC_SYSCLK_DIV16) || ((__HCLK__) == RCC_SYSCLK_DIV64) || \ + ((__HCLK__) == RCC_SYSCLK_DIV128) || ((__HCLK__) == RCC_SYSCLK_DIV256) || \ + ((__HCLK__) == RCC_SYSCLK_DIV512)) +#define IS_RCC_PCLK(__PCLK__) (((__PCLK__) == RCC_HCLK_DIV1) || ((__PCLK__) == RCC_HCLK_DIV2) || \ + ((__PCLK__) == RCC_HCLK_DIV4) || ((__PCLK__) == RCC_HCLK_DIV8) || \ + ((__PCLK__) == RCC_HCLK_DIV16)) +#define IS_RCC_MCO(__MCO__) ((__MCO__) == RCC_MCO) +#define IS_RCC_MCODIV(__DIV__) (((__DIV__) == RCC_MCODIV_1)) +#define IS_RCC_RTCCLKSOURCE(__SOURCE__) (((__SOURCE__) == RCC_RTCCLKSOURCE_NO_CLK) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_LSE) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_LSI) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV128)) + +/** + * @} + */ + +/* Exported types ------------------------------------------------------------*/ + +/** @defgroup RCC_Exported_Types RCC Exported Types + * @{ + */ + +/** + * @brief RCC PLL configuration structure definition + */ +typedef struct +{ + uint32_t PLLState; /*!< PLLState: The new state of the PLL. + This parameter can be a value of @ref RCC_PLL_Config */ + + uint32_t PLLSource; /*!< PLLSource: PLL entry clock source. + This parameter must be a value of @ref RCC_PLL_Clock_Source */ + + uint32_t PLLMUL; /*!< PLLMUL: Multiplication factor for PLL VCO input clock + This parameter must be a value of @ref RCCEx_PLL_Multiplication_Factor */ +} RCC_PLLInitTypeDef; + +/** + * @brief RCC System, AHB and APB busses clock configuration structure definition + */ +typedef struct +{ + uint32_t ClockType; /*!< The clock to be configured. + This parameter can be a value of @ref RCC_System_Clock_Type */ + + uint32_t SYSCLKSource; /*!< The clock source (SYSCLKS) used as system clock. + This parameter can be a value of @ref RCC_System_Clock_Source */ + + uint32_t AHBCLKDivider; /*!< The AHB clock (HCLK) divider. This clock is derived from the system clock (SYSCLK). + This parameter can be a value of @ref RCC_AHB_Clock_Source */ + + uint32_t APB1CLKDivider; /*!< The APB1 clock (PCLK1) divider. This clock is derived from the AHB clock (HCLK). + This parameter can be a value of @ref RCC_APB1_APB2_Clock_Source */ + + uint32_t APB2CLKDivider; /*!< The APB2 clock (PCLK2) divider. This clock is derived from the AHB clock (HCLK). + This parameter can be a value of @ref RCC_APB1_APB2_Clock_Source */ +} RCC_ClkInitTypeDef; + +/** + * @} + */ + +/* Exported constants --------------------------------------------------------*/ +/** @defgroup RCC_Exported_Constants RCC Exported Constants + * @{ + */ + +/** @defgroup RCC_PLL_Clock_Source PLL Clock Source + * @{ + */ + +#define RCC_PLLSOURCE_HSI_DIV2 ((uint32_t)0x00000000) /*!< HSI clock divided by 2 selected as PLL entry clock source */ +#define RCC_PLLSOURCE_HSE RCC_CFGR_PLLSRC /*!< HSE clock selected as PLL entry clock source */ + +/** + * @} + */ + +/** @defgroup RCC_Oscillator_Type Oscillator Type + * @{ + */ +#define RCC_OSCILLATORTYPE_NONE ((uint32_t)0x00000000) +#define RCC_OSCILLATORTYPE_HSE ((uint32_t)0x00000001) +#define RCC_OSCILLATORTYPE_HSI ((uint32_t)0x00000002) +#define RCC_OSCILLATORTYPE_LSE ((uint32_t)0x00000004) +#define RCC_OSCILLATORTYPE_LSI ((uint32_t)0x00000008) +/** + * @} + */ + +/** @defgroup RCC_HSE_Config HSE Config + * @{ + */ +#define RCC_HSE_OFF ((uint32_t)0x00000000) /*!< HSE clock deactivation */ +#define RCC_HSE_ON RCC_CR_HSEON /*!< HSE clock activation */ +#define RCC_HSE_BYPASS ((uint32_t)(RCC_CR_HSEBYP | RCC_CR_HSEON)) /*!< External clock source for HSE clock */ +/** + * @} + */ + +/** @defgroup RCC_LSE_Config LSE Config + * @{ + */ +#define RCC_LSE_OFF ((uint32_t)0x00000000) /*!< LSE clock deactivation */ +#define RCC_LSE_ON RCC_BDCR_LSEON /*!< LSE clock activation */ +#define RCC_LSE_BYPASS ((uint32_t)(RCC_BDCR_LSEBYP | RCC_BDCR_LSEON)) /*!< External clock source for LSE clock */ + +/** + * @} + */ + +/** @defgroup RCC_HSI_Config HSI Config + * @{ + */ +#define RCC_HSI_OFF ((uint32_t)0x00000000) /*!< HSI clock deactivation */ +#define RCC_HSI_ON RCC_CR_HSION /*!< HSI clock activation */ + +#define RCC_HSICALIBRATION_DEFAULT ((uint32_t)0x10) /* Default HSI calibration trimming value */ + +/** + * @} + */ + +/** @defgroup RCC_LSI_Config LSI Config + * @{ + */ +#define RCC_LSI_OFF ((uint32_t)0x00000000) /*!< LSI clock deactivation */ +#define RCC_LSI_ON RCC_CSR_LSION /*!< LSI clock activation */ + +/** + * @} + */ + +/** @defgroup RCC_PLL_Config PLL Config + * @{ + */ +#define RCC_PLL_NONE ((uint32_t)0x00000000) /*!< PLL is not configured */ +#define RCC_PLL_OFF ((uint32_t)0x00000001) /*!< PLL deactivation */ +#define RCC_PLL_ON ((uint32_t)0x00000002) /*!< PLL activation */ + +/** + * @} + */ + +/** @defgroup RCC_System_Clock_Type System Clock Type + * @{ + */ +#define RCC_CLOCKTYPE_SYSCLK ((uint32_t)0x00000001) /*!< SYSCLK to configure */ +#define RCC_CLOCKTYPE_HCLK ((uint32_t)0x00000002) /*!< HCLK to configure */ +#define RCC_CLOCKTYPE_PCLK1 ((uint32_t)0x00000004) /*!< PCLK1 to configure */ +#define RCC_CLOCKTYPE_PCLK2 ((uint32_t)0x00000008) /*!< PCLK2 to configure */ + +/** + * @} + */ + +/** @defgroup RCC_System_Clock_Source System Clock Source + * @{ + */ +#define RCC_SYSCLKSOURCE_HSI RCC_CFGR_SW_HSI /*!< HSI selected as system clock */ +#define RCC_SYSCLKSOURCE_HSE RCC_CFGR_SW_HSE /*!< HSE selected as system clock */ +#define RCC_SYSCLKSOURCE_PLLCLK RCC_CFGR_SW_PLL /*!< PLL selected as system clock */ + +/** + * @} + */ + +/** @defgroup RCC_System_Clock_Source_Status System Clock Source Status + * @{ + */ +#define RCC_SYSCLKSOURCE_STATUS_HSI RCC_CFGR_SWS_HSI /*!< HSI used as system clock */ +#define RCC_SYSCLKSOURCE_STATUS_HSE RCC_CFGR_SWS_HSE /*!< HSE used as system clock */ +#define RCC_SYSCLKSOURCE_STATUS_PLLCLK RCC_CFGR_SWS_PLL /*!< PLL used as system clock */ + +/** + * @} + */ + +/** @defgroup RCC_AHB_Clock_Source AHB Clock Source + * @{ + */ +#define RCC_SYSCLK_DIV1 RCC_CFGR_HPRE_DIV1 /*!< SYSCLK not divided */ +#define RCC_SYSCLK_DIV2 RCC_CFGR_HPRE_DIV2 /*!< SYSCLK divided by 2 */ +#define RCC_SYSCLK_DIV4 RCC_CFGR_HPRE_DIV4 /*!< SYSCLK divided by 4 */ +#define RCC_SYSCLK_DIV8 RCC_CFGR_HPRE_DIV8 /*!< SYSCLK divided by 8 */ +#define RCC_SYSCLK_DIV16 RCC_CFGR_HPRE_DIV16 /*!< SYSCLK divided by 16 */ +#define RCC_SYSCLK_DIV64 RCC_CFGR_HPRE_DIV64 /*!< SYSCLK divided by 64 */ +#define RCC_SYSCLK_DIV128 RCC_CFGR_HPRE_DIV128 /*!< SYSCLK divided by 128 */ +#define RCC_SYSCLK_DIV256 RCC_CFGR_HPRE_DIV256 /*!< SYSCLK divided by 256 */ +#define RCC_SYSCLK_DIV512 RCC_CFGR_HPRE_DIV512 /*!< SYSCLK divided by 512 */ + +/** + * @} + */ + +/** @defgroup RCC_APB1_APB2_Clock_Source APB1 APB2 Clock Source + * @{ + */ +#define RCC_HCLK_DIV1 RCC_CFGR_PPRE1_DIV1 /*!< HCLK not divided */ +#define RCC_HCLK_DIV2 RCC_CFGR_PPRE1_DIV2 /*!< HCLK divided by 2 */ +#define RCC_HCLK_DIV4 RCC_CFGR_PPRE1_DIV4 /*!< HCLK divided by 4 */ +#define RCC_HCLK_DIV8 RCC_CFGR_PPRE1_DIV8 /*!< HCLK divided by 8 */ +#define RCC_HCLK_DIV16 RCC_CFGR_PPRE1_DIV16 /*!< HCLK divided by 16 */ + +/** + * @} + */ + +/** @defgroup RCC_RTC_Clock_Source RTC Clock Source + * @{ + */ +#define RCC_RTCCLKSOURCE_NO_CLK ((uint32_t)0x00000000) /*!< No clock */ +#define RCC_RTCCLKSOURCE_LSE RCC_BDCR_RTCSEL_LSE /*!< LSE oscillator clock used as RTC clock */ +#define RCC_RTCCLKSOURCE_LSI RCC_BDCR_RTCSEL_LSI /*!< LSI oscillator clock used as RTC clock */ +#define RCC_RTCCLKSOURCE_HSE_DIV128 RCC_BDCR_RTCSEL_HSE /*!< HSE oscillator clock divided by 128 used as RTC clock */ +/** + * @} + */ + + +/** @defgroup RCC_MCO_Index MCO Index + * @{ + */ +#define RCC_MCO1 ((uint32_t)0x00000000) +#define RCC_MCO RCC_MCO1 /*!< MCO1 to be compliant with other families with 2 MCOs*/ + +/** + * @} + */ + +/** @defgroup RCC_MCOx_Clock_Prescaler MCO Clock Prescaler + * @{ + */ +#define RCC_MCODIV_1 ((uint32_t)0x00000000) + +/** + * @} + */ + +/** @defgroup RCC_Interrupt Interrupts + * @{ + */ +#define RCC_IT_LSIRDY ((uint8_t)RCC_CIR_LSIRDYF) /*!< LSI Ready Interrupt flag */ +#define RCC_IT_LSERDY ((uint8_t)RCC_CIR_LSERDYF) /*!< LSE Ready Interrupt flag */ +#define RCC_IT_HSIRDY ((uint8_t)RCC_CIR_HSIRDYF) /*!< HSI Ready Interrupt flag */ +#define RCC_IT_HSERDY ((uint8_t)RCC_CIR_HSERDYF) /*!< HSE Ready Interrupt flag */ +#define RCC_IT_PLLRDY ((uint8_t)RCC_CIR_PLLRDYF) /*!< PLL Ready Interrupt flag */ +#define RCC_IT_CSS ((uint8_t)RCC_CIR_CSSF) /*!< Clock Security System Interrupt flag */ +/** + * @} + */ + +/** @defgroup RCC_Flag Flags + * Elements values convention: XXXYYYYYb + * - YYYYY : Flag position in the register + * - XXX : Register index + * - 001: CR register + * - 010: BDCR register + * - 011: CSR register + * @{ + */ +/* Flags in the CR register */ +#define RCC_FLAG_HSIRDY ((uint8_t)((CR_REG_INDEX << 5) | POSITION_VAL(RCC_CR_HSIRDY))) /*!< Internal High Speed clock ready flag */ +#define RCC_FLAG_HSERDY ((uint8_t)((CR_REG_INDEX << 5) | POSITION_VAL(RCC_CR_HSERDY))) /*!< External High Speed clock ready flag */ +#define RCC_FLAG_PLLRDY ((uint8_t)((CR_REG_INDEX << 5) | POSITION_VAL(RCC_CR_PLLRDY))) /*!< PLL clock ready flag */ + +/* Flags in the CSR register */ +#define RCC_FLAG_LSIRDY ((uint8_t)((CSR_REG_INDEX << 5) | POSITION_VAL(RCC_CSR_LSIRDY))) /*!< Internal Low Speed oscillator Ready */ +#define RCC_FLAG_PINRST ((uint8_t)((CSR_REG_INDEX << 5) | POSITION_VAL(RCC_CSR_PINRSTF))) /*!< PIN reset flag */ +#define RCC_FLAG_PORRST ((uint8_t)((CSR_REG_INDEX << 5) | POSITION_VAL(RCC_CSR_PORRSTF))) /*!< POR/PDR reset flag */ +#define RCC_FLAG_SFTRST ((uint8_t)((CSR_REG_INDEX << 5) | POSITION_VAL(RCC_CSR_SFTRSTF))) /*!< Software Reset flag */ +#define RCC_FLAG_IWDGRST ((uint8_t)((CSR_REG_INDEX << 5) | POSITION_VAL(RCC_CSR_IWDGRSTF))) /*!< Independent Watchdog reset flag */ +#define RCC_FLAG_WWDGRST ((uint8_t)((CSR_REG_INDEX << 5) | POSITION_VAL(RCC_CSR_WWDGRSTF))) /*!< Window watchdog reset flag */ +#define RCC_FLAG_LPWRRST ((uint8_t)((CSR_REG_INDEX << 5) | POSITION_VAL(RCC_CSR_LPWRRSTF))) /*!< Low-Power reset flag */ + +/* Flags in the BDCR register */ +#define RCC_FLAG_LSERDY ((uint8_t)((BDCR_REG_INDEX << 5) | POSITION_VAL(RCC_BDCR_LSERDY))) /*!< External Low Speed oscillator Ready */ + +/** + * @} + */ + +/** + * @} + */ + +/* Exported macro ------------------------------------------------------------*/ + +/** @defgroup RCC_Exported_Macros RCC Exported Macros + * @{ + */ + +/** @defgroup RCC_Peripheral_Clock_Enable_Disable Peripheral Clock Enable Disable + * @brief Enable or disable the AHB1 peripheral clock. + * @note After reset, the peripheral clock (used for registers read/write access) + * is disabled and the application software has to enable this clock before + * using it. + * @{ + */ +#define __HAL_RCC_DMA1_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->AHBENR, RCC_AHBENR_DMA1EN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_DMA1EN);\ + UNUSED(tmpreg); \ + } while(0) + +#define __HAL_RCC_SRAM_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->AHBENR, RCC_AHBENR_SRAMEN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_SRAMEN);\ + UNUSED(tmpreg); \ + } while(0) + +#define __HAL_RCC_FLITF_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->AHBENR, RCC_AHBENR_FLITFEN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_FLITFEN);\ + UNUSED(tmpreg); \ + } while(0) + +#define __HAL_RCC_CRC_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->AHBENR, RCC_AHBENR_CRCEN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_CRCEN);\ + UNUSED(tmpreg); \ + } while(0) + +#define __HAL_RCC_DMA1_CLK_DISABLE() (RCC->AHBENR &= ~(RCC_AHBENR_DMA1EN)) +#define __HAL_RCC_SRAM_CLK_DISABLE() (RCC->AHBENR &= ~(RCC_AHBENR_SRAMEN)) +#define __HAL_RCC_FLITF_CLK_DISABLE() (RCC->AHBENR &= ~(RCC_AHBENR_FLITFEN)) +#define __HAL_RCC_CRC_CLK_DISABLE() (RCC->AHBENR &= ~(RCC_AHBENR_CRCEN)) + +/** + * @} + */ + +/** @defgroup RCC_AHB_Peripheral_Clock_Enable_Disable_Status AHB Peripheral Clock Enable Disable Status + * @brief Get the enable or disable status of the AHB peripheral clock. + * @note After reset, the peripheral clock (used for registers read/write access) + * is disabled and the application software has to enable this clock before + * using it. + * @{ + */ + +#define __HAL_RCC_DMA1_IS_CLK_ENABLED() ((RCC->AHBENR & (RCC_AHBENR_DMA1EN)) != RESET) +#define __HAL_RCC_DMA1_IS_CLK_DISABLED() ((RCC->AHBENR & (RCC_AHBENR_DMA1EN)) == RESET) +#define __HAL_RCC_SRAM_IS_CLK_ENABLED() ((RCC->AHBENR & (RCC_AHBENR_SRAMEN)) != RESET) +#define __HAL_RCC_SRAM_IS_CLK_DISABLED() ((RCC->AHBENR & (RCC_AHBENR_SRAMEN)) == RESET) +#define __HAL_RCC_FLITF_IS_CLK_ENABLED() ((RCC->AHBENR & (RCC_AHBENR_FLITFEN)) != RESET) +#define __HAL_RCC_FLITF_IS_CLK_DISABLED() ((RCC->AHBENR & (RCC_AHBENR_FLITFEN)) == RESET) +#define __HAL_RCC_CRC_IS_CLK_ENABLED() ((RCC->AHBENR & (RCC_AHBENR_CRCEN)) != RESET) +#define __HAL_RCC_CRC_IS_CLK_DISABLED() ((RCC->AHBENR & (RCC_AHBENR_CRCEN)) == RESET) + +/** + * @} + */ + +/** @defgroup RCC_APB1_Clock_Enable_Disable APB1 Clock Enable Disable + * @brief Enable or disable the Low Speed APB (APB1) peripheral clock. + * @note After reset, the peripheral clock (used for registers read/write access) + * is disabled and the application software has to enable this clock before + * using it. + * @{ + */ +#define __HAL_RCC_TIM2_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\ + UNUSED(tmpreg); \ + } while(0) + +#define __HAL_RCC_TIM3_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\ + UNUSED(tmpreg); \ + } while(0) + +#define __HAL_RCC_WWDG_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_WWDGEN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_WWDGEN);\ + UNUSED(tmpreg); \ + } while(0) + +#define __HAL_RCC_USART2_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_USART2EN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_USART2EN);\ + UNUSED(tmpreg); \ + } while(0) + +#define __HAL_RCC_I2C1_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C1EN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C1EN);\ + UNUSED(tmpreg); \ + } while(0) + +#define __HAL_RCC_BKP_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_BKPEN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_BKPEN);\ + UNUSED(tmpreg); \ + } while(0) + +#define __HAL_RCC_PWR_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_PWREN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_PWREN);\ + UNUSED(tmpreg); \ + } while(0) + +#define __HAL_RCC_TIM2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM2EN)) +#define __HAL_RCC_TIM3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM3EN)) +#define __HAL_RCC_WWDG_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_WWDGEN)) +#define __HAL_RCC_USART2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_USART2EN)) +#define __HAL_RCC_I2C1_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_I2C1EN)) + +#define __HAL_RCC_BKP_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_BKPEN)) +#define __HAL_RCC_PWR_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_PWREN)) + +/** + * @} + */ + +/** @defgroup RCC_APB1_Peripheral_Clock_Enable_Disable_Status APB1 Peripheral Clock Enable Disable Status + * @brief Get the enable or disable status of the APB1 peripheral clock. + * @note After reset, the peripheral clock (used for registers read/write access) + * is disabled and the application software has to enable this clock before + * using it. + * @{ + */ + +#define __HAL_RCC_TIM2_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM2EN)) != RESET) +#define __HAL_RCC_TIM2_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM2EN)) == RESET) +#define __HAL_RCC_TIM3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM3EN)) != RESET) +#define __HAL_RCC_TIM3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM3EN)) == RESET) +#define __HAL_RCC_WWDG_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_WWDGEN)) != RESET) +#define __HAL_RCC_WWDG_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_WWDGEN)) == RESET) +#define __HAL_RCC_USART2_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_USART2EN)) != RESET) +#define __HAL_RCC_USART2_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_USART2EN)) == RESET) +#define __HAL_RCC_I2C1_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C1EN)) != RESET) +#define __HAL_RCC_I2C1_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C1EN)) == RESET) +#define __HAL_RCC_BKP_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_BKPEN)) != RESET) +#define __HAL_RCC_BKP_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_BKPEN)) == RESET) +#define __HAL_RCC_PWR_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_PWREN)) != RESET) +#define __HAL_RCC_PWR_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_PWREN)) == RESET) + +/** + * @} + */ + +/** @defgroup RCC_APB2_Clock_Enable_Disable APB2 Clock Enable Disable + * @brief Enable or disable the High Speed APB (APB2) peripheral clock. + * @note After reset, the peripheral clock (used for registers read/write access) + * is disabled and the application software has to enable this clock before + * using it. + * @{ + */ +#define __HAL_RCC_AFIO_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_AFIOEN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_AFIOEN);\ + UNUSED(tmpreg); \ + } while(0) + +#define __HAL_RCC_GPIOA_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPAEN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPAEN);\ + UNUSED(tmpreg); \ + } while(0) + +#define __HAL_RCC_GPIOB_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPBEN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPBEN);\ + UNUSED(tmpreg); \ + } while(0) + +#define __HAL_RCC_GPIOC_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPCEN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPCEN);\ + UNUSED(tmpreg); \ + } while(0) + +#define __HAL_RCC_GPIOD_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPDEN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPDEN);\ + UNUSED(tmpreg); \ + } while(0) + +#define __HAL_RCC_ADC1_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC1EN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC1EN);\ + UNUSED(tmpreg); \ + } while(0) + +#define __HAL_RCC_TIM1_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM1EN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM1EN);\ + UNUSED(tmpreg); \ + } while(0) + +#define __HAL_RCC_SPI1_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI1EN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI1EN);\ + UNUSED(tmpreg); \ + } while(0) + +#define __HAL_RCC_USART1_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_USART1EN);\ + /* Delay after an RCC peripheral clock enabling */\ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_USART1EN);\ + UNUSED(tmpreg); \ + } while(0) + +#define __HAL_RCC_AFIO_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_AFIOEN)) +#define __HAL_RCC_GPIOA_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_IOPAEN)) +#define __HAL_RCC_GPIOB_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_IOPBEN)) +#define __HAL_RCC_GPIOC_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_IOPCEN)) +#define __HAL_RCC_GPIOD_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_IOPDEN)) +#define __HAL_RCC_ADC1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC1EN)) + +#define __HAL_RCC_TIM1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM1EN)) +#define __HAL_RCC_SPI1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI1EN)) +#define __HAL_RCC_USART1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_USART1EN)) + +/** + * @} + */ + +/** @defgroup RCC_APB2_Peripheral_Clock_Enable_Disable_Status APB2 Peripheral Clock Enable Disable Status + * @brief Get the enable or disable status of the APB2 peripheral clock. + * @note After reset, the peripheral clock (used for registers read/write access) + * is disabled and the application software has to enable this clock before + * using it. + * @{ + */ + +#define __HAL_RCC_AFIO_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_AFIOEN)) != RESET) +#define __HAL_RCC_AFIO_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_AFIOEN)) == RESET) +#define __HAL_RCC_GPIOA_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPAEN)) != RESET) +#define __HAL_RCC_GPIOA_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPAEN)) == RESET) +#define __HAL_RCC_GPIOB_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPBEN)) != RESET) +#define __HAL_RCC_GPIOB_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPBEN)) == RESET) +#define __HAL_RCC_GPIOC_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPCEN)) != RESET) +#define __HAL_RCC_GPIOC_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPCEN)) == RESET) +#define __HAL_RCC_GPIOD_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPDEN)) != RESET) +#define __HAL_RCC_GPIOD_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_IOPDEN)) == RESET) +#define __HAL_RCC_ADC1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC1EN)) != RESET) +#define __HAL_RCC_ADC1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC1EN)) == RESET) +#define __HAL_RCC_TIM1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM1EN)) != RESET) +#define __HAL_RCC_TIM1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM1EN)) == RESET) +#define __HAL_RCC_SPI1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI1EN)) != RESET) +#define __HAL_RCC_SPI1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI1EN)) == RESET) +#define __HAL_RCC_USART1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_USART1EN)) != RESET) +#define __HAL_RCC_USART1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_USART1EN)) == RESET) + +/** + * @} + */ + +/** @defgroup RCC_APB1_Force_Release_Reset APB1 Force Release Reset + * @brief Force or release APB1 peripheral reset. + * @{ + */ +#define __HAL_RCC_APB1_FORCE_RESET() (RCC->APB2RSTR = 0xFFFFFFFFU) +#define __HAL_RCC_TIM2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM2RST)) +#define __HAL_RCC_TIM3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM3RST)) +#define __HAL_RCC_WWDG_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_WWDGRST)) +#define __HAL_RCC_USART2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_USART2RST)) +#define __HAL_RCC_I2C1_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_I2C1RST)) + +#define __HAL_RCC_BKP_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_BKPRST)) +#define __HAL_RCC_PWR_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_PWRRST)) + +#define __HAL_RCC_APB1_RELEASE_RESET() (RCC->APB1RSTR = 0x00) +#define __HAL_RCC_TIM2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM2RST)) +#define __HAL_RCC_TIM3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM3RST)) +#define __HAL_RCC_WWDG_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_WWDGRST)) +#define __HAL_RCC_USART2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_USART2RST)) +#define __HAL_RCC_I2C1_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_I2C1RST)) + +#define __HAL_RCC_BKP_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_BKPRST)) +#define __HAL_RCC_PWR_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_PWRRST)) + +/** + * @} + */ + +/** @defgroup RCC_APB2_Force_Release_Reset APB2 Force Release Reset + * @brief Force or release APB2 peripheral reset. + * @{ + */ +#define __HAL_RCC_APB2_FORCE_RESET() (RCC->APB2RSTR = 0xFFFFFFFFU) +#define __HAL_RCC_AFIO_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_AFIORST)) +#define __HAL_RCC_GPIOA_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_IOPARST)) +#define __HAL_RCC_GPIOB_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_IOPBRST)) +#define __HAL_RCC_GPIOC_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_IOPCRST)) +#define __HAL_RCC_GPIOD_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_IOPDRST)) +#define __HAL_RCC_ADC1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_ADC1RST)) + +#define __HAL_RCC_TIM1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM1RST)) +#define __HAL_RCC_SPI1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI1RST)) +#define __HAL_RCC_USART1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_USART1RST)) + +#define __HAL_RCC_APB2_RELEASE_RESET() (RCC->APB2RSTR = 0x00) +#define __HAL_RCC_AFIO_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_AFIORST)) +#define __HAL_RCC_GPIOA_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_IOPARST)) +#define __HAL_RCC_GPIOB_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_IOPBRST)) +#define __HAL_RCC_GPIOC_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_IOPCRST)) +#define __HAL_RCC_GPIOD_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_IOPDRST)) +#define __HAL_RCC_ADC1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_ADC1RST)) + +#define __HAL_RCC_TIM1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM1RST)) +#define __HAL_RCC_SPI1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI1RST)) +#define __HAL_RCC_USART1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_USART1RST)) + +/** + * @} + */ + +/** @defgroup RCC_HSI_Configuration HSI Configuration + * @{ + */ + +/** @brief Macros to enable or disable the Internal High Speed oscillator (HSI). + * @note The HSI is stopped by hardware when entering STOP and STANDBY modes. + * @note HSI can not be stopped if it is used as system clock source. In this case, + * you have to select another source of the system clock then stop the HSI. + * @note After enabling the HSI, the application software should wait on HSIRDY + * flag to be set indicating that HSI clock is stable and can be used as + * system clock source. + * @note When the HSI is stopped, HSIRDY flag goes low after 6 HSI oscillator + * clock cycles. + */ +#define __HAL_RCC_HSI_ENABLE() (*(__IO uint32_t *) RCC_CR_HSION_BB = ENABLE) +#define __HAL_RCC_HSI_DISABLE() (*(__IO uint32_t *) RCC_CR_HSION_BB = DISABLE) + +/** @brief Macro to adjust the Internal High Speed oscillator (HSI) calibration value. + * @note The calibration is used to compensate for the variations in voltage + * and temperature that influence the frequency of the internal HSI RC. + * @param _HSICALIBRATIONVALUE_ specifies the calibration trimming value. + * (default is RCC_HSICALIBRATION_DEFAULT). + * This parameter must be a number between 0 and 0x1F. + */ +#define __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(_HSICALIBRATIONVALUE_) \ + (MODIFY_REG(RCC->CR, RCC_CR_HSITRIM, (uint32_t)(_HSICALIBRATIONVALUE_) << POSITION_VAL(RCC_CR_HSITRIM))) + +/** + * @} + */ + +/** @defgroup RCC_LSI_Configuration LSI Configuration + * @{ + */ + +/** @brief Macro to enable the Internal Low Speed oscillator (LSI). + * @note After enabling the LSI, the application software should wait on + * LSIRDY flag to be set indicating that LSI clock is stable and can + * be used to clock the IWDG and/or the RTC. + */ +#define __HAL_RCC_LSI_ENABLE() (*(__IO uint32_t *) RCC_CSR_LSION_BB = ENABLE) + +/** @brief Macro to disable the Internal Low Speed oscillator (LSI). + * @note LSI can not be disabled if the IWDG is running. + * @note When the LSI is stopped, LSIRDY flag goes low after 6 LSI oscillator + * clock cycles. + */ +#define __HAL_RCC_LSI_DISABLE() (*(__IO uint32_t *) RCC_CSR_LSION_BB = DISABLE) + +/** + * @} + */ + +/** @defgroup RCC_HSE_Configuration HSE Configuration + * @{ + */ + +/** + * @brief Macro to configure the External High Speed oscillator (HSE). + * @note Transition HSE Bypass to HSE On and HSE On to HSE Bypass are not + * supported by this macro. User should request a transition to HSE Off + * first and then HSE On or HSE Bypass. + * @note After enabling the HSE (RCC_HSE_ON or RCC_HSE_Bypass), the application + * software should wait on HSERDY flag to be set indicating that HSE clock + * is stable and can be used to clock the PLL and/or system clock. + * @note HSE state can not be changed if it is used directly or through the + * PLL as system clock. In this case, you have to select another source + * of the system clock then change the HSE state (ex. disable it). + * @note The HSE is stopped by hardware when entering STOP and STANDBY modes. + * @note This function reset the CSSON bit, so if the clock security system(CSS) + * was previously enabled you have to enable it again after calling this + * function. + * @param __STATE__ specifies the new state of the HSE. + * This parameter can be one of the following values: + * @arg @ref RCC_HSE_OFF turn OFF the HSE oscillator, HSERDY flag goes low after + * 6 HSE oscillator clock cycles. + * @arg @ref RCC_HSE_ON turn ON the HSE oscillator + * @arg @ref RCC_HSE_BYPASS HSE oscillator bypassed with external clock + */ +#define __HAL_RCC_HSE_CONFIG(__STATE__) \ + do{ \ + if ((__STATE__) == RCC_HSE_ON) \ + { \ + SET_BIT(RCC->CR, RCC_CR_HSEON); \ + } \ + else if ((__STATE__) == RCC_HSE_OFF) \ + { \ + CLEAR_BIT(RCC->CR, RCC_CR_HSEON); \ + CLEAR_BIT(RCC->CR, RCC_CR_HSEBYP); \ + } \ + else if ((__STATE__) == RCC_HSE_BYPASS) \ + { \ + SET_BIT(RCC->CR, RCC_CR_HSEBYP); \ + SET_BIT(RCC->CR, RCC_CR_HSEON); \ + } \ + else \ + { \ + CLEAR_BIT(RCC->CR, RCC_CR_HSEON); \ + CLEAR_BIT(RCC->CR, RCC_CR_HSEBYP); \ + } \ + }while(0) + +/** + * @} + */ + +/** @defgroup RCC_LSE_Configuration LSE Configuration + * @{ + */ + +/** + * @brief Macro to configure the External Low Speed oscillator (LSE). + * @note Transitions LSE Bypass to LSE On and LSE On to LSE Bypass are not supported by this macro. + * @note As the LSE is in the Backup domain and write access is denied to + * this domain after reset, you have to enable write access using + * @ref HAL_PWR_EnableBkUpAccess() function before to configure the LSE + * (to be done once after reset). + * @note After enabling the LSE (RCC_LSE_ON or RCC_LSE_BYPASS), the application + * software should wait on LSERDY flag to be set indicating that LSE clock + * is stable and can be used to clock the RTC. + * @param __STATE__ specifies the new state of the LSE. + * This parameter can be one of the following values: + * @arg @ref RCC_LSE_OFF turn OFF the LSE oscillator, LSERDY flag goes low after + * 6 LSE oscillator clock cycles. + * @arg @ref RCC_LSE_ON turn ON the LSE oscillator. + * @arg @ref RCC_LSE_BYPASS LSE oscillator bypassed with external clock. + */ +#define __HAL_RCC_LSE_CONFIG(__STATE__) \ + do{ \ + if ((__STATE__) == RCC_LSE_ON) \ + { \ + SET_BIT(RCC->BDCR, RCC_BDCR_LSEON); \ + } \ + else if ((__STATE__) == RCC_LSE_OFF) \ + { \ + CLEAR_BIT(RCC->BDCR, RCC_BDCR_LSEON); \ + CLEAR_BIT(RCC->BDCR, RCC_BDCR_LSEBYP); \ + } \ + else if ((__STATE__) == RCC_LSE_BYPASS) \ + { \ + SET_BIT(RCC->BDCR, RCC_BDCR_LSEBYP); \ + SET_BIT(RCC->BDCR, RCC_BDCR_LSEON); \ + } \ + else \ + { \ + CLEAR_BIT(RCC->BDCR, RCC_BDCR_LSEON); \ + CLEAR_BIT(RCC->BDCR, RCC_BDCR_LSEBYP); \ + } \ + }while(0) + +/** + * @} + */ + +/** @defgroup RCC_PLL_Configuration PLL Configuration + * @{ + */ + +/** @brief Macro to enable the main PLL. + * @note After enabling the main PLL, the application software should wait on + * PLLRDY flag to be set indicating that PLL clock is stable and can + * be used as system clock source. + * @note The main PLL is disabled by hardware when entering STOP and STANDBY modes. + */ +#define __HAL_RCC_PLL_ENABLE() (*(__IO uint32_t *) RCC_CR_PLLON_BB = ENABLE) + +/** @brief Macro to disable the main PLL. + * @note The main PLL can not be disabled if it is used as system clock source + */ +#define __HAL_RCC_PLL_DISABLE() (*(__IO uint32_t *) RCC_CR_PLLON_BB = DISABLE) + +/** @brief Macro to configure the main PLL clock source and multiplication factors. + * @note This function must be used only when the main PLL is disabled. + * + * @param __RCC_PLLSOURCE__ specifies the PLL entry clock source. + * This parameter can be one of the following values: + * @arg @ref RCC_PLLSOURCE_HSI_DIV2 HSI oscillator clock selected as PLL clock entry + * @arg @ref RCC_PLLSOURCE_HSE HSE oscillator clock selected as PLL clock entry + * @param __PLLMUL__ specifies the multiplication factor for PLL VCO output clock + * This parameter can be one of the following values: + * @arg @ref RCC_PLL_MUL4 PLLVCO = PLL clock entry x 4 + * @arg @ref RCC_PLL_MUL6 PLLVCO = PLL clock entry x 6 + @if STM32F105xC + * @arg @ref RCC_PLL_MUL6_5 PLLVCO = PLL clock entry x 6.5 + @elseif STM32F107xC + * @arg @ref RCC_PLL_MUL6_5 PLLVCO = PLL clock entry x 6.5 + @else + * @arg @ref RCC_PLL_MUL2 PLLVCO = PLL clock entry x 2 + * @arg @ref RCC_PLL_MUL3 PLLVCO = PLL clock entry x 3 + * @arg @ref RCC_PLL_MUL10 PLLVCO = PLL clock entry x 10 + * @arg @ref RCC_PLL_MUL11 PLLVCO = PLL clock entry x 11 + * @arg @ref RCC_PLL_MUL12 PLLVCO = PLL clock entry x 12 + * @arg @ref RCC_PLL_MUL13 PLLVCO = PLL clock entry x 13 + * @arg @ref RCC_PLL_MUL14 PLLVCO = PLL clock entry x 14 + * @arg @ref RCC_PLL_MUL15 PLLVCO = PLL clock entry x 15 + * @arg @ref RCC_PLL_MUL16 PLLVCO = PLL clock entry x 16 + @endif + * @arg @ref RCC_PLL_MUL8 PLLVCO = PLL clock entry x 8 + * @arg @ref RCC_PLL_MUL9 PLLVCO = PLL clock entry x 9 + * + */ +#define __HAL_RCC_PLL_CONFIG(__RCC_PLLSOURCE__, __PLLMUL__)\ + MODIFY_REG(RCC->CFGR, (RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL),((__RCC_PLLSOURCE__) | (__PLLMUL__) )) + +/** @brief Get oscillator clock selected as PLL input clock + * @retval The clock source used for PLL entry. The returned value can be one + * of the following: + * @arg @ref RCC_PLLSOURCE_HSI_DIV2 HSI oscillator clock selected as PLL input clock + * @arg @ref RCC_PLLSOURCE_HSE HSE oscillator clock selected as PLL input clock + */ +#define __HAL_RCC_GET_PLL_OSCSOURCE() ((uint32_t)(READ_BIT(RCC->CFGR, RCC_CFGR_PLLSRC))) + +/** + * @} + */ + +/** @defgroup RCC_Get_Clock_source Get Clock source + * @{ + */ + +/** + * @brief Macro to configure the system clock source. + * @param __SYSCLKSOURCE__ specifies the system clock source. + * This parameter can be one of the following values: + * @arg @ref RCC_SYSCLKSOURCE_HSI HSI oscillator is used as system clock source. + * @arg @ref RCC_SYSCLKSOURCE_HSE HSE oscillator is used as system clock source. + * @arg @ref RCC_SYSCLKSOURCE_PLLCLK PLL output is used as system clock source. + */ +#define __HAL_RCC_SYSCLK_CONFIG(__SYSCLKSOURCE__) \ + MODIFY_REG(RCC->CFGR, RCC_CFGR_SW, (__SYSCLKSOURCE__)) + +/** @brief Macro to get the clock source used as system clock. + * @retval The clock source used as system clock. The returned value can be one + * of the following: + * @arg @ref RCC_SYSCLKSOURCE_STATUS_HSI HSI used as system clock + * @arg @ref RCC_SYSCLKSOURCE_STATUS_HSE HSE used as system clock + * @arg @ref RCC_SYSCLKSOURCE_STATUS_PLLCLK PLL used as system clock + */ +#define __HAL_RCC_GET_SYSCLK_SOURCE() ((uint32_t)(READ_BIT(RCC->CFGR,RCC_CFGR_SWS))) + +/** + * @} + */ + +/** @defgroup RCCEx_MCOx_Clock_Config RCC Extended MCOx Clock Config + * @{ + */ + +#if defined(RCC_CFGR_MCO_3) +/** @brief Macro to configure the MCO clock. + * @param __MCOCLKSOURCE__ specifies the MCO clock source. + * This parameter can be one of the following values: + * @arg @ref RCC_MCO1SOURCE_NOCLOCK No clock selected as MCO clock + * @arg @ref RCC_MCO1SOURCE_SYSCLK System clock (SYSCLK) selected as MCO clock + * @arg @ref RCC_MCO1SOURCE_HSI HSI selected as MCO clock + * @arg @ref RCC_MCO1SOURCE_HSE HSE selected as MCO clock + * @arg @ref RCC_MCO1SOURCE_PLLCLK PLL clock divided by 2 selected as MCO clock + * @arg @ref RCC_MCO1SOURCE_PLL2CLK PLL2 clock selected by 2 selected as MCO clock + * @arg @ref RCC_MCO1SOURCE_PLL3CLK_DIV2 PLL3 clock divided by 2 selected as MCO clock + * @arg @ref RCC_MCO1SOURCE_EXT_HSE XT1 external 3-25 MHz oscillator clock selected (for Ethernet) as MCO clock + * @arg @ref RCC_MCO1SOURCE_PLL3CLK PLL3 clock selected (for Ethernet) as MCO clock + * @param __MCODIV__ specifies the MCO clock prescaler. + * This parameter can be one of the following values: + * @arg @ref RCC_MCODIV_1 No division applied on MCO clock source + */ +#else +/** @brief Macro to configure the MCO clock. + * @param __MCOCLKSOURCE__ specifies the MCO clock source. + * This parameter can be one of the following values: + * @arg @ref RCC_MCO1SOURCE_NOCLOCK No clock selected as MCO clock + * @arg @ref RCC_MCO1SOURCE_SYSCLK System clock (SYSCLK) selected as MCO clock + * @arg @ref RCC_MCO1SOURCE_HSI HSI selected as MCO clock + * @arg @ref RCC_MCO1SOURCE_HSE HSE selected as MCO clock + * @arg @ref RCC_MCO1SOURCE_PLLCLK PLL clock divided by 2 selected as MCO clock + * @param __MCODIV__ specifies the MCO clock prescaler. + * This parameter can be one of the following values: + * @arg @ref RCC_MCODIV_1 No division applied on MCO clock source + */ +#endif + +#define __HAL_RCC_MCO1_CONFIG(__MCOCLKSOURCE__, __MCODIV__) \ + MODIFY_REG(RCC->CFGR, RCC_CFGR_MCO, (__MCOCLKSOURCE__)) + + +/** + * @} + */ + + /** @defgroup RCC_RTC_Clock_Configuration RCC RTC Clock Configuration + * @{ + */ + +/** @brief Macro to configure the RTC clock (RTCCLK). + * @note As the RTC clock configuration bits are in the Backup domain and write + * access is denied to this domain after reset, you have to enable write + * access using the Power Backup Access macro before to configure + * the RTC clock source (to be done once after reset). + * @note Once the RTC clock is configured it can't be changed unless the + * Backup domain is reset using @ref __HAL_RCC_BACKUPRESET_FORCE() macro, or by + * a Power On Reset (POR). + * + * @param __RTC_CLKSOURCE__ specifies the RTC clock source. + * This parameter can be one of the following values: + * @arg @ref RCC_RTCCLKSOURCE_NO_CLK No clock selected as RTC clock + * @arg @ref RCC_RTCCLKSOURCE_LSE LSE selected as RTC clock + * @arg @ref RCC_RTCCLKSOURCE_LSI LSI selected as RTC clock + * @arg @ref RCC_RTCCLKSOURCE_HSE_DIV128 HSE divided by 128 selected as RTC clock + * @note If the LSE or LSI is used as RTC clock source, the RTC continues to + * work in STOP and STANDBY modes, and can be used as wakeup source. + * However, when the HSE clock is used as RTC clock source, the RTC + * cannot be used in STOP and STANDBY modes. + * @note The maximum input clock frequency for RTC is 1MHz (when using HSE as + * RTC clock source). + */ +#define __HAL_RCC_RTC_CONFIG(__RTC_CLKSOURCE__) MODIFY_REG(RCC->BDCR, RCC_BDCR_RTCSEL, (__RTC_CLKSOURCE__)) + +/** @brief Macro to get the RTC clock source. + * @retval The clock source can be one of the following values: + * @arg @ref RCC_RTCCLKSOURCE_NO_CLK No clock selected as RTC clock + * @arg @ref RCC_RTCCLKSOURCE_LSE LSE selected as RTC clock + * @arg @ref RCC_RTCCLKSOURCE_LSI LSI selected as RTC clock + * @arg @ref RCC_RTCCLKSOURCE_HSE_DIV128 HSE divided by 128 selected as RTC clock + */ +#define __HAL_RCC_GET_RTC_SOURCE() (READ_BIT(RCC->BDCR, RCC_BDCR_RTCSEL)) + +/** @brief Macro to enable the the RTC clock. + * @note These macros must be used only after the RTC clock source was selected. + */ +#define __HAL_RCC_RTC_ENABLE() (*(__IO uint32_t *) RCC_BDCR_RTCEN_BB = ENABLE) + +/** @brief Macro to disable the the RTC clock. + * @note These macros must be used only after the RTC clock source was selected. + */ +#define __HAL_RCC_RTC_DISABLE() (*(__IO uint32_t *) RCC_BDCR_RTCEN_BB = DISABLE) + +/** @brief Macro to force the Backup domain reset. + * @note This function resets the RTC peripheral (including the backup registers) + * and the RTC clock source selection in RCC_BDCR register. + */ +#define __HAL_RCC_BACKUPRESET_FORCE() (*(__IO uint32_t *) RCC_BDCR_BDRST_BB = ENABLE) + +/** @brief Macros to release the Backup domain reset. + */ +#define __HAL_RCC_BACKUPRESET_RELEASE() (*(__IO uint32_t *) RCC_BDCR_BDRST_BB = DISABLE) + +/** + * @} + */ + +/** @defgroup RCC_Flags_Interrupts_Management Flags Interrupts Management + * @brief macros to manage the specified RCC Flags and interrupts. + * @{ + */ + +/** @brief Enable RCC interrupt. + * @param __INTERRUPT__ specifies the RCC interrupt sources to be enabled. + * This parameter can be any combination of the following values: + * @arg @ref RCC_IT_LSIRDY LSI ready interrupt + * @arg @ref RCC_IT_LSERDY LSE ready interrupt + * @arg @ref RCC_IT_HSIRDY HSI ready interrupt + * @arg @ref RCC_IT_HSERDY HSE ready interrupt + * @arg @ref RCC_IT_PLLRDY main PLL ready interrupt + @if STM32F105xx + * @arg @ref RCC_IT_PLL2RDY Main PLL2 ready interrupt. + * @arg @ref RCC_IT_PLLI2S2RDY Main PLLI2S ready interrupt. + @elsif STM32F107xx + * @arg @ref RCC_IT_PLL2RDY Main PLL2 ready interrupt. + * @arg @ref RCC_IT_PLLI2S2RDY Main PLLI2S ready interrupt. + @endif + */ +#define __HAL_RCC_ENABLE_IT(__INTERRUPT__) (*(__IO uint8_t *) RCC_CIR_BYTE1_ADDRESS |= (__INTERRUPT__)) + +/** @brief Disable RCC interrupt. + * @param __INTERRUPT__ specifies the RCC interrupt sources to be disabled. + * This parameter can be any combination of the following values: + * @arg @ref RCC_IT_LSIRDY LSI ready interrupt + * @arg @ref RCC_IT_LSERDY LSE ready interrupt + * @arg @ref RCC_IT_HSIRDY HSI ready interrupt + * @arg @ref RCC_IT_HSERDY HSE ready interrupt + * @arg @ref RCC_IT_PLLRDY main PLL ready interrupt + @if STM32F105xx + * @arg @ref RCC_IT_PLL2RDY Main PLL2 ready interrupt. + * @arg @ref RCC_IT_PLLI2S2RDY Main PLLI2S ready interrupt. + @elsif STM32F107xx + * @arg @ref RCC_IT_PLL2RDY Main PLL2 ready interrupt. + * @arg @ref RCC_IT_PLLI2S2RDY Main PLLI2S ready interrupt. + @endif + */ +#define __HAL_RCC_DISABLE_IT(__INTERRUPT__) (*(__IO uint8_t *) RCC_CIR_BYTE1_ADDRESS &= (uint8_t)(~(__INTERRUPT__))) + +/** @brief Clear the RCC's interrupt pending bits. + * @param __INTERRUPT__ specifies the interrupt pending bit to clear. + * This parameter can be any combination of the following values: + * @arg @ref RCC_IT_LSIRDY LSI ready interrupt. + * @arg @ref RCC_IT_LSERDY LSE ready interrupt. + * @arg @ref RCC_IT_HSIRDY HSI ready interrupt. + * @arg @ref RCC_IT_HSERDY HSE ready interrupt. + * @arg @ref RCC_IT_PLLRDY Main PLL ready interrupt. + @if STM32F105xx + * @arg @ref RCC_IT_PLL2RDY Main PLL2 ready interrupt. + * @arg @ref RCC_IT_PLLI2S2RDY Main PLLI2S ready interrupt. + @elsif STM32F107xx + * @arg @ref RCC_IT_PLL2RDY Main PLL2 ready interrupt. + * @arg @ref RCC_IT_PLLI2S2RDY Main PLLI2S ready interrupt. + @endif + * @arg @ref RCC_IT_CSS Clock Security System interrupt + */ +#define __HAL_RCC_CLEAR_IT(__INTERRUPT__) (*(__IO uint8_t *) RCC_CIR_BYTE2_ADDRESS = (__INTERRUPT__)) + +/** @brief Check the RCC's interrupt has occurred or not. + * @param __INTERRUPT__ specifies the RCC interrupt source to check. + * This parameter can be one of the following values: + * @arg @ref RCC_IT_LSIRDY LSI ready interrupt. + * @arg @ref RCC_IT_LSERDY LSE ready interrupt. + * @arg @ref RCC_IT_HSIRDY HSI ready interrupt. + * @arg @ref RCC_IT_HSERDY HSE ready interrupt. + * @arg @ref RCC_IT_PLLRDY Main PLL ready interrupt. + @if STM32F105xx + * @arg @ref RCC_IT_PLL2RDY Main PLL2 ready interrupt. + * @arg @ref RCC_IT_PLLI2S2RDY Main PLLI2S ready interrupt. + @elsif STM32F107xx + * @arg @ref RCC_IT_PLL2RDY Main PLL2 ready interrupt. + * @arg @ref RCC_IT_PLLI2S2RDY Main PLLI2S ready interrupt. + @endif + * @arg @ref RCC_IT_CSS Clock Security System interrupt + * @retval The new state of __INTERRUPT__ (TRUE or FALSE). + */ +#define __HAL_RCC_GET_IT(__INTERRUPT__) ((RCC->CIR & (__INTERRUPT__)) == (__INTERRUPT__)) + +/** @brief Set RMVF bit to clear the reset flags. + * The reset flags are RCC_FLAG_PINRST, RCC_FLAG_PORRST, RCC_FLAG_SFTRST, + * RCC_FLAG_IWDGRST, RCC_FLAG_WWDGRST, RCC_FLAG_LPWRRST + */ +#define __HAL_RCC_CLEAR_RESET_FLAGS() (*(__IO uint32_t *)RCC_CSR_RMVF_BB = ENABLE) + +/** @brief Check RCC flag is set or not. + * @param __FLAG__ specifies the flag to check. + * This parameter can be one of the following values: + * @arg @ref RCC_FLAG_HSIRDY HSI oscillator clock ready. + * @arg @ref RCC_FLAG_HSERDY HSE oscillator clock ready. + * @arg @ref RCC_FLAG_PLLRDY Main PLL clock ready. + @if STM32F105xx + * @arg @ref RCC_FLAG_PLL2RDY Main PLL2 clock ready. + * @arg @ref RCC_FLAG_PLLI2SRDY Main PLLI2S clock ready. + @elsif STM32F107xx + * @arg @ref RCC_FLAG_PLL2RDY Main PLL2 clock ready. + * @arg @ref RCC_FLAG_PLLI2SRDY Main PLLI2S clock ready. + @endif + * @arg @ref RCC_FLAG_LSERDY LSE oscillator clock ready. + * @arg @ref RCC_FLAG_LSIRDY LSI oscillator clock ready. + * @arg @ref RCC_FLAG_PINRST Pin reset. + * @arg @ref RCC_FLAG_PORRST POR/PDR reset. + * @arg @ref RCC_FLAG_SFTRST Software reset. + * @arg @ref RCC_FLAG_IWDGRST Independent Watchdog reset. + * @arg @ref RCC_FLAG_WWDGRST Window Watchdog reset. + * @arg @ref RCC_FLAG_LPWRRST Low Power reset. + * @retval The new state of __FLAG__ (TRUE or FALSE). + */ +#define __HAL_RCC_GET_FLAG(__FLAG__) (((((__FLAG__) >> 5) == CR_REG_INDEX)? RCC->CR : \ + ((((__FLAG__) >> 5) == BDCR_REG_INDEX)? RCC->BDCR : \ + RCC->CSR)) & ((uint32_t)1 << ((__FLAG__) & RCC_FLAG_MASK))) + +/** + * @} + */ + +/** + * @} + */ + +/* Include RCC HAL Extension module */ +#include "stm32f1xx_hal_rcc_ex.h" + +/* Exported functions --------------------------------------------------------*/ +/** @addtogroup RCC_Exported_Functions + * @{ + */ + +/** @addtogroup RCC_Exported_Functions_Group1 + * @{ + */ + +/* Initialization and de-initialization functions ******************************/ +void HAL_RCC_DeInit(void); +HAL_StatusTypeDef HAL_RCC_OscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct); +HAL_StatusTypeDef HAL_RCC_ClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t FLatency); + +/** + * @} + */ + +/** @addtogroup RCC_Exported_Functions_Group2 + * @{ + */ + +/* Peripheral Control functions ************************************************/ +void HAL_RCC_MCOConfig(uint32_t RCC_MCOx, uint32_t RCC_MCOSource, uint32_t RCC_MCODiv); +void HAL_RCC_EnableCSS(void); +void HAL_RCC_DisableCSS(void); +uint32_t HAL_RCC_GetSysClockFreq(void); +uint32_t HAL_RCC_GetHCLKFreq(void); +uint32_t HAL_RCC_GetPCLK1Freq(void); +uint32_t HAL_RCC_GetPCLK2Freq(void); +void HAL_RCC_GetOscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct); +void HAL_RCC_GetClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t *pFLatency); + +/* CSS NMI IRQ handler */ +void HAL_RCC_NMI_IRQHandler(void); + +/* User Callbacks in non blocking mode (IT mode) */ +void HAL_RCC_CSSCallback(void); + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F1xx_HAL_RCC_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ +