--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/l476rg/Drivers/STM32L4xx_HAL_Driver/Src/stm32l4xx_hal_tim_ex.c	Thu Jan 12 02:45:43 2017 +0300
@@ -0,0 +1,2242 @@
+/**
+  ******************************************************************************
+  * @file    stm32l4xx_hal_tim_ex.c
+  * @author  MCD Application Team
+  * @version V1.6.0
+  * @date    28-October-2016
+  * @brief   TIM HAL module driver.
+  *          This file provides firmware functions to manage the following
+  *          functionalities of the Timer Extended peripheral:
+  *           + Time Hall Sensor Interface Initialization
+  *           + Time Hall Sensor Interface Start
+  *           + Time Complementary signal break and dead time configuration
+  *           + Time Master and Slave synchronization configuration
+  *           + Time Output Compare/PWM Channel Configuration (for channels 5 and 6)
+  *           + Time OCRef clear configuration
+  *           + Timer remapping capabilities configuration
+  @verbatim
+  ==============================================================================
+                      ##### TIMER Extended features #####
+  ==============================================================================
+  [..]
+    The Timer Extended features include:
+    (#) Complementary outputs with programmable dead-time for :
+        (++) Output Compare
+        (++) PWM generation (Edge and Center-aligned Mode)
+        (++) One-pulse mode output
+    (#) Synchronization circuit to control the timer with external signals and to
+        interconnect several timers together.
+    (#) Break input to put the timer output signals in reset state or in a known state.
+    (#) Supports incremental (quadrature) encoder and hall-sensor circuitry for
+        positioning purposes
+
+            ##### How to use this driver #####
+  ==============================================================================
+    [..]
+     (#) Initialize the TIM low level resources by implementing the following functions
+         depending on the selected feature:
+           (++) Hall Sensor output : HAL_TIMEx_HallSensor_MspInit()
+
+     (#) Initialize the TIM low level resources :
+        (##) Enable the TIM interface clock using __HAL_RCC_TIMx_CLK_ENABLE();
+        (##) TIM pins configuration
+            (+++) Enable the clock for the TIM GPIOs using the following function:
+              __HAL_RCC_GPIOx_CLK_ENABLE();
+            (+++) Configure these TIM pins in Alternate function mode using HAL_GPIO_Init();
+
+     (#) The external Clock can be configured, if needed (the default clock is the
+         internal clock from the APBx), using the following function:
+         HAL_TIM_ConfigClockSource, the clock configuration should be done before
+         any start function.
+
+     (#) Configure the TIM in the desired functioning mode using one of the
+         initialization function of this driver:
+          (++) HAL_TIMEx_HallSensor_Init() and HAL_TIMEx_ConfigCommutationEvent(): to use the
+              Timer Hall Sensor Interface and the commutation event with the corresponding
+              Interrupt and DMA request if needed (Note that One Timer is used to interface
+             with the Hall sensor Interface and another Timer should be used to use
+             the commutation event).
+
+     (#) Activate the TIM peripheral using one of the start functions:
+           (++) Complementary Output Compare : HAL_TIMEx_OCN_Start(), HAL_TIMEx_OCN_Start_DMA(), HAL_TIMEx_OC_Start_IT()
+           (++) Complementary PWM generation : HAL_TIMEx_PWMN_Start(), HAL_TIMEx_PWMN_Start_DMA(), HAL_TIMEx_PWMN_Start_IT()
+           (++) Complementary One-pulse mode output : HAL_TIMEx_OnePulseN_Start(), HAL_TIMEx_OnePulseN_Start_IT()
+           (++) Hall Sensor output : HAL_TIMEx_HallSensor_Start(), HAL_TIMEx_HallSensor_Start_DMA(), HAL_TIMEx_HallSensor_Start_IT().
+
+
+  @endverbatim
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; COPYRIGHT(c) 2016 STMicroelectronics</center></h2>
+  *
+  * Redistribution and use in source and binary forms, with or without modification,
+  * are permitted provided that the following conditions are met:
+  *   1. Redistributions of source code must retain the above copyright notice,
+  *      this list of conditions and the following disclaimer.
+  *   2. Redistributions in binary form must reproduce the above copyright notice,
+  *      this list of conditions and the following disclaimer in the documentation
+  *      and/or other materials provided with the distribution.
+  *   3. Neither the name of STMicroelectronics nor the names of its contributors
+  *      may be used to endorse or promote products derived from this software
+  *      without specific prior written permission.
+  *
+  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+  *
+  ******************************************************************************
+*/
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l4xx_hal.h"
+
+/** @addtogroup STM32L4xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup TIMEx TIMEx
+  * @brief TIM Extended HAL module driver
+  * @{
+  */
+
+#ifdef HAL_TIM_MODULE_ENABLED
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+#define BDTR_BKF_SHIFT (16)
+#define BDTR_BK2F_SHIFT (20)
+#define TIMx_ETRSEL_MASK ((uint32_t)0x0001C000) 
+
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+static void TIM_CCxNChannelCmd(TIM_TypeDef* TIMx, uint32_t Channel, uint32_t ChannelNState);
+
+/* Private functions ---------------------------------------------------------*/
+
+/* Exported functions --------------------------------------------------------*/
+/** @defgroup TIMEx_Exported_Functions TIM Extended Exported Functions
+  * @{
+  */
+
+/** @defgroup TIMEx_Exported_Functions_Group1 Extended Timer Hall Sensor functions
+  * @brief    Timer Hall Sensor functions
+  *
+@verbatim
+  ==============================================================================
+                      ##### Timer Hall Sensor functions #####
+  ==============================================================================
+  [..]
+    This section provides functions allowing to:
+    (+) Initialize and configure TIM HAL Sensor.
+    (+) De-initialize TIM HAL Sensor.
+    (+) Start the Hall Sensor Interface.
+    (+) Stop the Hall Sensor Interface.
+    (+) Start the Hall Sensor Interface and enable interrupts.
+    (+) Stop the Hall Sensor Interface and disable interrupts.
+    (+) Start the Hall Sensor Interface and enable DMA transfers.
+    (+) Stop the Hall Sensor Interface and disable DMA transfers.
+
+@endverbatim
+  * @{
+  */
+/**
+  * @brief  Initializes the TIM Hall Sensor Interface and initialize the associated handle.
+  * @param  htim: TIM Encoder Interface handle
+  * @param  sConfig: TIM Hall Sensor configuration structure
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Init(TIM_HandleTypeDef *htim, TIM_HallSensor_InitTypeDef* sConfig)
+{
+  TIM_OC_InitTypeDef OC_Config;
+
+  /* Check the TIM handle allocation */
+  if(htim == NULL)
+  {
+    return HAL_ERROR;
+  }
+
+  assert_param(IS_TIM_XOR_INSTANCE(htim->Instance));
+  assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode));
+  assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision));
+  assert_param(IS_TIM_IC_POLARITY(sConfig->IC1Polarity));
+  assert_param(IS_TIM_IC_PRESCALER(sConfig->IC1Prescaler));
+  assert_param(IS_TIM_IC_FILTER(sConfig->IC1Filter));
+
+  if(htim->State == HAL_TIM_STATE_RESET)
+  {
+    /* Allocate lock resource and initialize it */
+    htim->Lock = HAL_UNLOCKED;
+
+    /* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */
+    HAL_TIMEx_HallSensor_MspInit(htim);
+  }
+
+  /* Set the TIM state */
+  htim->State = HAL_TIM_STATE_BUSY;
+
+  /* Configure the Time base in the Encoder Mode */
+  TIM_Base_SetConfig(htim->Instance, &htim->Init);
+
+  /* Configure the Channel 1 as Input Channel to interface with the three Outputs of the  Hall sensor */
+  TIM_TI1_SetConfig(htim->Instance, sConfig->IC1Polarity, TIM_ICSELECTION_TRC, sConfig->IC1Filter);
+
+  /* Reset the IC1PSC Bits */
+  htim->Instance->CCMR1 &= ~TIM_CCMR1_IC1PSC;
+  /* Set the IC1PSC value */
+  htim->Instance->CCMR1 |= sConfig->IC1Prescaler;
+
+  /* Enable the Hall sensor interface (XOR function of the three inputs) */
+  htim->Instance->CR2 |= TIM_CR2_TI1S;
+
+  /* Select the TIM_TS_TI1F_ED signal as Input trigger for the TIM */
+  htim->Instance->SMCR &= ~TIM_SMCR_TS;
+  htim->Instance->SMCR |= TIM_TS_TI1F_ED;
+
+  /* Use the TIM_TS_TI1F_ED signal to reset the TIM counter each edge detection */
+  htim->Instance->SMCR &= ~TIM_SMCR_SMS;
+  htim->Instance->SMCR |= TIM_SLAVEMODE_RESET;
+
+  /* Program channel 2 in PWM 2 mode with the desired Commutation_Delay*/
+  OC_Config.OCFastMode = TIM_OCFAST_DISABLE;
+  OC_Config.OCIdleState = TIM_OCIDLESTATE_RESET;
+  OC_Config.OCMode = TIM_OCMODE_PWM2;
+  OC_Config.OCNIdleState = TIM_OCNIDLESTATE_RESET;
+  OC_Config.OCNPolarity = TIM_OCNPOLARITY_HIGH;
+  OC_Config.OCPolarity = TIM_OCPOLARITY_HIGH;
+  OC_Config.Pulse = sConfig->Commutation_Delay;
+
+  TIM_OC2_SetConfig(htim->Instance, &OC_Config);
+
+  /* Select OC2REF as trigger output on TRGO: write the MMS bits in the TIMx_CR2
+    register to 101 */
+  htim->Instance->CR2 &= ~TIM_CR2_MMS;
+  htim->Instance->CR2 |= TIM_TRGO_OC2REF;
+
+  /* Initialize the TIM state*/
+  htim->State= HAL_TIM_STATE_READY;
+
+  return HAL_OK;
+}
+
+/**
+  * @brief  DeInitialize the TIM Hall Sensor interface
+  * @param  htim: TIM Hall Sensor handle
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_DeInit(TIM_HandleTypeDef *htim)
+{
+  /* Check the parameters */
+  assert_param(IS_TIM_INSTANCE(htim->Instance));
+
+  htim->State = HAL_TIM_STATE_BUSY;
+
+  /* Disable the TIM Peripheral Clock */
+  __HAL_TIM_DISABLE(htim);
+
+  /* DeInit the low level hardware: GPIO, CLOCK, NVIC */
+  HAL_TIMEx_HallSensor_MspDeInit(htim);
+
+  /* Change TIM state */
+  htim->State = HAL_TIM_STATE_RESET;
+
+  /* Release Lock */
+  __HAL_UNLOCK(htim);
+
+  return HAL_OK;
+}
+
+/**
+  * @brief  Initializes the TIM Hall Sensor MSP.
+  * @param  htim: TIM handle
+  * @retval None
+  */
+__weak void HAL_TIMEx_HallSensor_MspInit(TIM_HandleTypeDef *htim)
+{
+  /* Prevent unused argument(s) compilation warning */
+  UNUSED(htim);
+
+  /* NOTE : This function should not be modified, when the callback is needed,
+            the HAL_TIMEx_HallSensor_MspInit could be implemented in the user file
+   */
+}
+
+/**
+  * @brief  DeInitialize TIM Hall Sensor MSP.
+  * @param  htim: TIM handle
+  * @retval None
+  */
+__weak void HAL_TIMEx_HallSensor_MspDeInit(TIM_HandleTypeDef *htim)
+{
+  /* Prevent unused argument(s) compilation warning */
+  UNUSED(htim);
+
+  /* NOTE : This function should not be modified, when the callback is needed,
+            the HAL_TIMEx_HallSensor_MspDeInit could be implemented in the user file
+   */
+}
+
+/**
+  * @brief  Starts the TIM Hall Sensor Interface.
+  * @param  htim : TIM Hall Sensor handle
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start(TIM_HandleTypeDef *htim)
+{
+  /* Check the parameters */
+  assert_param(IS_TIM_XOR_INSTANCE(htim->Instance));
+
+  /* Enable the Input Capture channels 1
+    (in the Hall Sensor Interface the Three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */
+  TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE);
+
+  /* Enable the Peripheral */
+  __HAL_TIM_ENABLE(htim);
+
+  /* Return function status */
+  return HAL_OK;
+}
+
+/**
+  * @brief  Stops the TIM Hall sensor Interface.
+  * @param  htim : TIM Hall Sensor handle
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop(TIM_HandleTypeDef *htim)
+{
+  /* Check the parameters */
+  assert_param(IS_TIM_XOR_INSTANCE(htim->Instance));
+
+  /* Disable the Input Capture channels 1, 2 and 3
+    (in the Hall Sensor Interface the Three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */
+  TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE);
+
+  /* Disable the Peripheral */
+  __HAL_TIM_DISABLE(htim);
+
+  /* Return function status */
+  return HAL_OK;
+}
+
+/**
+  * @brief  Starts the TIM Hall Sensor Interface in interrupt mode.
+  * @param  htim : TIM Hall Sensor handle
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start_IT(TIM_HandleTypeDef *htim)
+{
+  /* Check the parameters */
+  assert_param(IS_TIM_XOR_INSTANCE(htim->Instance));
+
+  /* Enable the capture compare Interrupts 1 event */
+  __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1);
+
+  /* Enable the Input Capture channels 1
+    (in the Hall Sensor Interface the Three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */
+  TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE);
+
+  /* Enable the Peripheral */
+  __HAL_TIM_ENABLE(htim);
+
+  /* Return function status */
+  return HAL_OK;
+}
+
+/**
+  * @brief  Stops the TIM Hall Sensor Interface in interrupt mode.
+  * @param  htim : TIM handle
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop_IT(TIM_HandleTypeDef *htim)
+{
+  /* Check the parameters */
+  assert_param(IS_TIM_XOR_INSTANCE(htim->Instance));
+
+  /* Disable the Input Capture channels 1
+    (in the Hall Sensor Interface the Three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */
+  TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE);
+
+  /* Disable the capture compare Interrupts event */
+  __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1);
+
+  /* Disable the Peripheral */
+  __HAL_TIM_DISABLE(htim);
+
+  /* Return function status */
+  return HAL_OK;
+}
+
+/**
+  * @brief  Starts the TIM Hall Sensor Interface in DMA mode.
+  * @param  htim : TIM Hall Sensor handle
+  * @param  pData: The destination Buffer address.
+  * @param  Length: The length of data to be transferred from TIM peripheral to memory.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start_DMA(TIM_HandleTypeDef *htim, uint32_t *pData, uint16_t Length)
+{
+  /* Check the parameters */
+  assert_param(IS_TIM_XOR_INSTANCE(htim->Instance));
+
+   if((htim->State == HAL_TIM_STATE_BUSY))
+  {
+     return HAL_BUSY;
+  }
+  else if((htim->State == HAL_TIM_STATE_READY))
+  {
+    if(((uint32_t)pData == 0 ) && (Length > 0))
+    {
+      return HAL_ERROR;
+    }
+    else
+    {
+      htim->State = HAL_TIM_STATE_BUSY;
+    }
+  }
+  /* Enable the Input Capture channels 1
+    (in the Hall Sensor Interface the Three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */
+  TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE);
+
+  /* Set the DMA Input Capture 1 Callback */
+  htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMACaptureCplt;
+  /* Set the DMA error callback */
+  htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ;
+
+  /* Enable the DMA channel for Capture 1*/
+  HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->CCR1, (uint32_t)pData, Length);
+
+  /* Enable the capture compare 1 Interrupt */
+  __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1);
+
+  /* Enable the Peripheral */
+  __HAL_TIM_ENABLE(htim);
+
+  /* Return function status */
+  return HAL_OK;
+}
+
+/**
+  * @brief  Stops the TIM Hall Sensor Interface in DMA mode.
+  * @param  htim : TIM handle
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop_DMA(TIM_HandleTypeDef *htim)
+{
+  /* Check the parameters */
+  assert_param(IS_TIM_XOR_INSTANCE(htim->Instance));
+
+  /* Disable the Input Capture channels 1
+    (in the Hall Sensor Interface the Three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */
+  TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE);
+
+
+  /* Disable the capture compare Interrupts 1 event */
+  __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1);
+
+  /* Disable the Peripheral */
+  __HAL_TIM_DISABLE(htim);
+
+  /* Return function status */
+  return HAL_OK;
+}
+
+/**
+  * @}
+  */
+
+/** @defgroup TIMEx_Exported_Functions_Group2 Extended Timer Complementary Output Compare functions
+  *  @brief   Timer Complementary Output Compare functions
+  *
+@verbatim
+  ==============================================================================
+              ##### Timer Complementary Output Compare functions #####
+  ==============================================================================
+  [..]
+    This section provides functions allowing to:
+    (+) Start the Complementary Output Compare/PWM.
+    (+) Stop the Complementary Output Compare/PWM.
+    (+) Start the Complementary Output Compare/PWM and enable interrupts.
+    (+) Stop the Complementary Output Compare/PWM and disable interrupts.
+    (+) Start the Complementary Output Compare/PWM and enable DMA transfers.
+    (+) Stop the Complementary Output Compare/PWM and disable DMA transfers.
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Starts the TIM Output Compare signal generation on the complementary
+  *         output.
+  * @param  htim : TIM Output Compare handle
+  * @param  Channel : TIM Channel to be enabled
+  *          This parameter can be one of the following values:
+  *            @arg TIM_CHANNEL_1: TIM Channel 1 selected
+  *            @arg TIM_CHANNEL_2: TIM Channel 2 selected
+  *            @arg TIM_CHANNEL_3: TIM Channel 3 selected
+  *            @arg TIM_CHANNEL_4: TIM Channel 4 selected
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_OCN_Start(TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+  /* Check the parameters */
+  assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+  /* Enable the Capture compare channel N */
+  TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE);
+
+  /* Enable the Main Ouput */
+  __HAL_TIM_MOE_ENABLE(htim);
+
+  /* Enable the Peripheral */
+  __HAL_TIM_ENABLE(htim);
+
+  /* Return function status */
+  return HAL_OK;
+}
+
+/**
+  * @brief  Stops the TIM Output Compare signal generation on the complementary
+  *         output.
+  * @param  htim : TIM handle
+  * @param  Channel : TIM Channel to be disabled
+  *          This parameter can be one of the following values:
+  *            @arg TIM_CHANNEL_1: TIM Channel 1 selected
+  *            @arg TIM_CHANNEL_2: TIM Channel 2 selected
+  *            @arg TIM_CHANNEL_3: TIM Channel 3 selected
+  *            @arg TIM_CHANNEL_4: TIM Channel 4 selected
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_OCN_Stop(TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+  /* Check the parameters */
+  assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+  /* Disable the Capture compare channel N */
+  TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE);
+
+  /* Disable the Main Ouput */
+  __HAL_TIM_MOE_DISABLE(htim);
+
+  /* Disable the Peripheral */
+  __HAL_TIM_DISABLE(htim);
+
+  /* Return function status */
+  return HAL_OK;
+}
+
+/**
+  * @brief  Starts the TIM Output Compare signal generation in interrupt mode
+  *         on the complementary output.
+  * @param  htim : TIM OC handle
+  * @param  Channel : TIM Channel to be enabled
+  *          This parameter can be one of the following values:
+  *            @arg TIM_CHANNEL_1: TIM Channel 1 selected
+  *            @arg TIM_CHANNEL_2: TIM Channel 2 selected
+  *            @arg TIM_CHANNEL_3: TIM Channel 3 selected
+  *            @arg TIM_CHANNEL_4: TIM Channel 4 selected
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_OCN_Start_IT(TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+  /* Check the parameters */
+  assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+  switch (Channel)
+  {
+    case TIM_CHANNEL_1:
+    {
+      /* Enable the TIM Output Compare interrupt */
+      __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1);
+    }
+    break;
+
+    case TIM_CHANNEL_2:
+    {
+      /* Enable the TIM Output Compare interrupt */
+      __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2);
+    }
+    break;
+
+    case TIM_CHANNEL_3:
+    {
+      /* Enable the TIM Output Compare interrupt */
+      __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC3);
+    }
+    break;
+
+    case TIM_CHANNEL_4:
+    {
+      /* Enable the TIM Output Compare interrupt */
+      __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC4);
+    }
+    break;
+
+    default:
+    break;
+  }
+
+  /* Enable the TIM Break interrupt */
+  __HAL_TIM_ENABLE_IT(htim, TIM_IT_BREAK);
+  
+  /* Enable the Capture compare channel N */
+  TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE);
+
+  /* Enable the Main Ouput */
+  __HAL_TIM_MOE_ENABLE(htim);
+
+  /* Enable the Peripheral */
+  __HAL_TIM_ENABLE(htim);
+
+  /* Return function status */
+  return HAL_OK;
+}
+
+/**
+  * @brief  Stops the TIM Output Compare signal generation in interrupt mode
+  *         on the complementary output.
+  * @param  htim : TIM Output Compare handle
+  * @param  Channel : TIM Channel to be disabled
+  *          This parameter can be one of the following values:
+  *            @arg TIM_CHANNEL_1: TIM Channel 1 selected
+  *            @arg TIM_CHANNEL_2: TIM Channel 2 selected
+  *            @arg TIM_CHANNEL_3: TIM Channel 3 selected
+  *            @arg TIM_CHANNEL_4: TIM Channel 4 selected
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+  uint32_t tmpccer = 0;
+
+  /* Check the parameters */
+  assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+  switch (Channel)
+  {
+    case TIM_CHANNEL_1:
+    {
+      /* Disable the TIM Output Compare interrupt */
+      __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1);
+    }
+    break;
+
+    case TIM_CHANNEL_2:
+    {
+      /* Disable the TIM Output Compare interrupt */
+      __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2);
+    }
+    break;
+
+    case TIM_CHANNEL_3:
+    {
+      /* Disable the TIM Output Compare interrupt */
+      __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC3);
+    }
+    break;
+
+    case TIM_CHANNEL_4:
+    {
+      /* Disable the TIM Output Compare interrupt */
+      __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC4);
+    }
+    break;
+
+    default:
+    break;
+  }
+
+  /* Disable the Capture compare channel N */
+  TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE);
+
+  /* Disable the TIM Break interrupt (only if no more channel is active) */
+  tmpccer = htim->Instance->CCER;
+  if ((tmpccer & (TIM_CCER_CC1NE | TIM_CCER_CC2NE | TIM_CCER_CC3NE)) == RESET)
+  {
+    __HAL_TIM_DISABLE_IT(htim, TIM_IT_BREAK);
+  }
+
+  /* Disable the Main Ouput */
+  __HAL_TIM_MOE_DISABLE(htim);
+
+  /* Disable the Peripheral */
+  __HAL_TIM_DISABLE(htim);
+
+  /* Return function status */
+  return HAL_OK;
+}
+
+/**
+  * @brief  Starts the TIM Output Compare signal generation in DMA mode
+  *         on the complementary output.
+  * @param  htim : TIM Output Compare handle
+  * @param  Channel : TIM Channel to be enabled
+  *          This parameter can be one of the following values:
+  *            @arg TIM_CHANNEL_1: TIM Channel 1 selected
+  *            @arg TIM_CHANNEL_2: TIM Channel 2 selected
+  *            @arg TIM_CHANNEL_3: TIM Channel 3 selected
+  *            @arg TIM_CHANNEL_4: TIM Channel 4 selected
+  * @param  pData: The source Buffer address.
+  * @param  Length: The length of data to be transferred from memory to TIM peripheral
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_OCN_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length)
+{
+  /* Check the parameters */
+  assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+  if((htim->State == HAL_TIM_STATE_BUSY))
+  {
+     return HAL_BUSY;
+  }
+  else if((htim->State == HAL_TIM_STATE_READY))
+  {
+    if(((uint32_t)pData == 0 ) && (Length > 0))
+    {
+      return HAL_ERROR;
+    }
+    else
+    {
+      htim->State = HAL_TIM_STATE_BUSY;
+    }
+  }
+  switch (Channel)
+  {
+    case TIM_CHANNEL_1:
+    {
+      /* Set the DMA Period elapsed callback */
+      htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMADelayPulseCplt;
+
+      /* Set the DMA error callback */
+      htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ;
+
+      /* Enable the DMA channel */
+      HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)pData, (uint32_t)&htim->Instance->CCR1, Length);
+
+      /* Enable the TIM Output Compare DMA request */
+      __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1);
+    }
+    break;
+
+    case TIM_CHANNEL_2:
+    {
+      /* Set the DMA Period elapsed callback */
+      htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMADelayPulseCplt;
+
+      /* Set the DMA error callback */
+      htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ;
+
+      /* Enable the DMA channel */
+      HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)pData, (uint32_t)&htim->Instance->CCR2, Length);
+
+      /* Enable the TIM Output Compare DMA request */
+      __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2);
+    }
+    break;
+
+    case TIM_CHANNEL_3:
+{
+      /* Set the DMA Period elapsed callback */
+      htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMADelayPulseCplt;
+
+      /* Set the DMA error callback */
+      htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ;
+
+      /* Enable the DMA channel */
+      HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)pData, (uint32_t)&htim->Instance->CCR3,Length);
+
+      /* Enable the TIM Output Compare DMA request */
+      __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC3);
+    }
+    break;
+
+    case TIM_CHANNEL_4:
+    {
+     /* Set the DMA Period elapsed callback */
+      htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMADelayPulseCplt;
+
+      /* Set the DMA error callback */
+      htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ;
+
+      /* Enable the DMA channel */
+      HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)pData, (uint32_t)&htim->Instance->CCR4, Length);
+
+      /* Enable the TIM Output Compare DMA request */
+      __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC4);
+    }
+    break;
+
+    default:
+    break;
+  }
+
+  /* Enable the Capture compare channel N */
+  TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE);
+
+  /* Enable the Main Ouput */
+  __HAL_TIM_MOE_ENABLE(htim);
+
+  /* Enable the Peripheral */
+  __HAL_TIM_ENABLE(htim);
+
+  /* Return function status */
+  return HAL_OK;
+}
+
+/**
+  * @brief  Stops the TIM Output Compare signal generation in DMA mode
+  *         on the complementary output.
+  * @param  htim : TIM Output Compare handle
+  * @param  Channel : TIM Channel to be disabled
+  *          This parameter can be one of the following values:
+  *            @arg TIM_CHANNEL_1: TIM Channel 1 selected
+  *            @arg TIM_CHANNEL_2: TIM Channel 2 selected
+  *            @arg TIM_CHANNEL_3: TIM Channel 3 selected
+  *            @arg TIM_CHANNEL_4: TIM Channel 4 selected
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+  /* Check the parameters */
+  assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+  switch (Channel)
+  {
+    case TIM_CHANNEL_1:
+    {
+      /* Disable the TIM Output Compare DMA request */
+      __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1);
+    }
+    break;
+
+    case TIM_CHANNEL_2:
+    {
+      /* Disable the TIM Output Compare DMA request */
+      __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2);
+    }
+    break;
+
+    case TIM_CHANNEL_3:
+    {
+      /* Disable the TIM Output Compare DMA request */
+      __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC3);
+    }
+    break;
+
+    case TIM_CHANNEL_4:
+    {
+      /* Disable the TIM Output Compare interrupt */
+      __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC4);
+    }
+    break;
+
+    default:
+    break;
+  }
+
+  /* Disable the Capture compare channel N */
+  TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE);
+
+  /* Disable the Main Ouput */
+  __HAL_TIM_MOE_DISABLE(htim);
+
+  /* Disable the Peripheral */
+  __HAL_TIM_DISABLE(htim);
+
+  /* Change the htim state */
+  htim->State = HAL_TIM_STATE_READY;
+
+  /* Return function status */
+  return HAL_OK;
+}
+
+/**
+  * @}
+  */
+
+/** @defgroup TIMEx_Exported_Functions_Group3 Extended Timer Complementary PWM functions
+  * @brief    Timer Complementary PWM functions
+  *
+@verbatim
+  ==============================================================================
+                 ##### Timer Complementary PWM functions #####
+  ==============================================================================
+  [..]
+    This section provides functions allowing to:
+    (+) Start the Complementary PWM.
+    (+) Stop the Complementary PWM.
+    (+) Start the Complementary PWM and enable interrupts.
+    (+) Stop the Complementary PWM and disable interrupts.
+    (+) Start the Complementary PWM and enable DMA transfers.
+    (+) Stop the Complementary PWM and disable DMA transfers.
+    (+) Start the Complementary Input Capture measurement.
+    (+) Stop the Complementary Input Capture.
+    (+) Start the Complementary Input Capture and enable interrupts.
+    (+) Stop the Complementary Input Capture and disable interrupts.
+    (+) Start the Complementary Input Capture and enable DMA transfers.
+    (+) Stop the Complementary Input Capture and disable DMA transfers.
+    (+) Start the Complementary One Pulse generation.
+    (+) Stop the Complementary One Pulse.
+    (+) Start the Complementary One Pulse and enable interrupts.
+    (+) Stop the Complementary One Pulse and disable interrupts.
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Starts the PWM signal generation on the complementary output.
+  * @param  htim : TIM handle
+  * @param  Channel : TIM Channel to be enabled
+  *          This parameter can be one of the following values:
+  *            @arg TIM_CHANNEL_1: TIM Channel 1 selected
+  *            @arg TIM_CHANNEL_2: TIM Channel 2 selected
+  *            @arg TIM_CHANNEL_3: TIM Channel 3 selected
+  *            @arg TIM_CHANNEL_4: TIM Channel 4 selected
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Start(TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+  /* Check the parameters */
+  assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+  /* Enable the complementary PWM output  */
+  TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE);
+
+  /* Enable the Main Ouput */
+  __HAL_TIM_MOE_ENABLE(htim);
+
+  /* Enable the Peripheral */
+  __HAL_TIM_ENABLE(htim);
+
+  /* Return function status */
+  return HAL_OK;
+}
+
+/**
+  * @brief  Stops the PWM signal generation on the complementary output.
+  * @param  htim : TIM handle
+  * @param  Channel : TIM Channel to be disabled
+  *          This parameter can be one of the following values:
+  *            @arg TIM_CHANNEL_1: TIM Channel 1 selected
+  *            @arg TIM_CHANNEL_2: TIM Channel 2 selected
+  *            @arg TIM_CHANNEL_3: TIM Channel 3 selected
+  *            @arg TIM_CHANNEL_4: TIM Channel 4 selected
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop(TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+  /* Check the parameters */
+  assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+  /* Disable the complementary PWM output  */
+  TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE);
+
+  /* Disable the Main Ouput */
+  __HAL_TIM_MOE_DISABLE(htim);
+
+  /* Disable the Peripheral */
+  __HAL_TIM_DISABLE(htim);
+
+  /* Return function status */
+  return HAL_OK;
+}
+
+/**
+  * @brief  Starts the PWM signal generation in interrupt mode on the
+  *         complementary output.
+  * @param  htim : TIM handle
+  * @param  Channel : TIM Channel to be disabled
+  *          This parameter can be one of the following values:
+  *            @arg TIM_CHANNEL_1: TIM Channel 1 selected
+  *            @arg TIM_CHANNEL_2: TIM Channel 2 selected
+  *            @arg TIM_CHANNEL_3: TIM Channel 3 selected
+  *            @arg TIM_CHANNEL_4: TIM Channel 4 selected
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_IT(TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+  /* Check the parameters */
+  assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+  switch (Channel)
+  {
+    case TIM_CHANNEL_1:
+    {
+      /* Enable the TIM Capture/Compare 1 interrupt */
+      __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1);
+    }
+    break;
+
+    case TIM_CHANNEL_2:
+    {
+      /* Enable the TIM Capture/Compare 2 interrupt */
+      __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2);
+    }
+    break;
+
+    case TIM_CHANNEL_3:
+    {
+      /* Enable the TIM Capture/Compare 3 interrupt */
+      __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC3);
+    }
+    break;
+
+    case TIM_CHANNEL_4:
+    {
+      /* Enable the TIM Capture/Compare 4 interrupt */
+      __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC4);
+    }
+    break;
+
+    default:
+    break;
+  }
+
+  /* Enable the TIM Break interrupt */
+  __HAL_TIM_ENABLE_IT(htim, TIM_IT_BREAK);
+
+  /* Enable the complementary PWM output  */
+  TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE);
+
+  /* Enable the Main Ouput */
+  __HAL_TIM_MOE_ENABLE(htim);
+
+  /* Enable the Peripheral */
+  __HAL_TIM_ENABLE(htim);
+
+  /* Return function status */
+  return HAL_OK;
+}
+
+/**
+  * @brief  Stops the PWM signal generation in interrupt mode on the
+  *         complementary output.
+  * @param  htim : TIM handle
+  * @param  Channel : TIM Channel to be disabled
+  *          This parameter can be one of the following values:
+  *            @arg TIM_CHANNEL_1: TIM Channel 1 selected
+  *            @arg TIM_CHANNEL_2: TIM Channel 2 selected
+  *            @arg TIM_CHANNEL_3: TIM Channel 3 selected
+  *            @arg TIM_CHANNEL_4: TIM Channel 4 selected
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_IT (TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+  uint32_t tmpccer = 0;
+
+  /* Check the parameters */
+  assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+  switch (Channel)
+  {
+    case TIM_CHANNEL_1:
+    {
+      /* Disable the TIM Capture/Compare 1 interrupt */
+      __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1);
+    }
+    break;
+
+    case TIM_CHANNEL_2:
+    {
+      /* Disable the TIM Capture/Compare 2 interrupt */
+      __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2);
+    }
+    break;
+
+    case TIM_CHANNEL_3:
+    {
+      /* Disable the TIM Capture/Compare 3 interrupt */
+      __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC3);
+    }
+    break;
+
+    case TIM_CHANNEL_4:
+    {
+      /* Disable the TIM Capture/Compare 3 interrupt */
+      __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC4);
+    }
+    break;
+
+    default:
+    break;
+  }
+
+  /* Disable the complementary PWM output  */
+  TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE);
+
+  
+  /* Disable the TIM Break interrupt (only if no more channel is active) */
+  tmpccer = htim->Instance->CCER;
+  if ((tmpccer & (TIM_CCER_CC1NE | TIM_CCER_CC2NE | TIM_CCER_CC3NE)) == RESET)
+  {
+    __HAL_TIM_DISABLE_IT(htim, TIM_IT_BREAK);
+  }
+
+  /* Disable the Main Ouput */
+  __HAL_TIM_MOE_DISABLE(htim);
+
+  /* Disable the Peripheral */
+  __HAL_TIM_DISABLE(htim);
+
+  /* Return function status */
+  return HAL_OK;
+}
+
+/**
+  * @brief  Starts the TIM PWM signal generation in DMA mode on the
+  *         complementary output
+  * @param  htim : TIM handle
+  * @param  Channel : TIM Channel to be enabled
+  *          This parameter can be one of the following values:
+  *            @arg TIM_CHANNEL_1: TIM Channel 1 selected
+  *            @arg TIM_CHANNEL_2: TIM Channel 2 selected
+  *            @arg TIM_CHANNEL_3: TIM Channel 3 selected
+  *            @arg TIM_CHANNEL_4: TIM Channel 4 selected
+  * @param  pData: The source Buffer address.
+  * @param  Length: The length of data to be transferred from memory to TIM peripheral
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length)
+{
+  /* Check the parameters */
+  assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+  if((htim->State == HAL_TIM_STATE_BUSY))
+  {
+     return HAL_BUSY;
+  }
+  else if((htim->State == HAL_TIM_STATE_READY))
+  {
+    if(((uint32_t)pData == 0 ) && (Length > 0))
+    {
+      return HAL_ERROR;
+    }
+    else
+    {
+      htim->State = HAL_TIM_STATE_BUSY;
+    }
+  }
+  switch (Channel)
+  {
+    case TIM_CHANNEL_1:
+    {
+      /* Set the DMA Period elapsed callback */
+      htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMADelayPulseCplt;
+
+      /* Set the DMA error callback */
+      htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ;
+
+      /* Enable the DMA channel */
+      HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)pData, (uint32_t)&htim->Instance->CCR1, Length);
+
+      /* Enable the TIM Capture/Compare 1 DMA request */
+      __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1);
+    }
+    break;
+
+    case TIM_CHANNEL_2:
+    {
+      /* Set the DMA Period elapsed callback */
+      htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMADelayPulseCplt;
+
+      /* Set the DMA error callback */
+      htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ;
+
+      /* Enable the DMA channel */
+      HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)pData, (uint32_t)&htim->Instance->CCR2, Length);
+
+      /* Enable the TIM Capture/Compare 2 DMA request */
+      __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2);
+    }
+    break;
+
+    case TIM_CHANNEL_3:
+    {
+      /* Set the DMA Period elapsed callback */
+      htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMADelayPulseCplt;
+
+      /* Set the DMA error callback */
+      htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ;
+
+      /* Enable the DMA channel */
+      HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)pData, (uint32_t)&htim->Instance->CCR3,Length);
+
+      /* Enable the TIM Capture/Compare 3 DMA request */
+      __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC3);
+    }
+    break;
+
+    case TIM_CHANNEL_4:
+    {
+     /* Set the DMA Period elapsed callback */
+      htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMADelayPulseCplt;
+
+      /* Set the DMA error callback */
+      htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ;
+
+      /* Enable the DMA channel */
+      HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)pData, (uint32_t)&htim->Instance->CCR4, Length);
+
+      /* Enable the TIM Capture/Compare 4 DMA request */
+      __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC4);
+    }
+    break;
+
+    default:
+    break;
+  }
+
+  /* Enable the complementary PWM output  */
+  TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE);
+
+  /* Enable the Main Ouput */
+  __HAL_TIM_MOE_ENABLE(htim);
+
+  /* Enable the Peripheral */
+  __HAL_TIM_ENABLE(htim);
+
+  /* Return function status */
+  return HAL_OK;
+}
+
+/**
+  * @brief  Stops the TIM PWM signal generation in DMA mode on the complementary
+  *         output
+  * @param  htim : TIM handle
+  * @param  Channel : TIM Channel to be disabled
+  *          This parameter can be one of the following values:
+  *            @arg TIM_CHANNEL_1: TIM Channel 1 selected
+  *            @arg TIM_CHANNEL_2: TIM Channel 2 selected
+  *            @arg TIM_CHANNEL_3: TIM Channel 3 selected
+  *            @arg TIM_CHANNEL_4: TIM Channel 4 selected
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+  /* Check the parameters */
+  assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+  switch (Channel)
+  {
+    case TIM_CHANNEL_1:
+    {
+      /* Disable the TIM Capture/Compare 1 DMA request */
+      __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1);
+    }
+    break;
+
+    case TIM_CHANNEL_2:
+    {
+      /* Disable the TIM Capture/Compare 2 DMA request */
+      __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2);
+    }
+    break;
+
+    case TIM_CHANNEL_3:
+    {
+      /* Disable the TIM Capture/Compare 3 DMA request */
+      __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC3);
+    }
+    break;
+
+    case TIM_CHANNEL_4:
+    {
+      /* Disable the TIM Capture/Compare 4 DMA request */
+      __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC4);
+    }
+    break;
+
+    default:
+    break;
+  }
+
+  /* Disable the complementary PWM output */
+  TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE);
+
+  /* Disable the Main Ouput */
+  __HAL_TIM_MOE_DISABLE(htim);
+
+  /* Disable the Peripheral */
+  __HAL_TIM_DISABLE(htim);
+
+  /* Change the htim state */
+  htim->State = HAL_TIM_STATE_READY;
+
+  /* Return function status */
+  return HAL_OK;
+}
+
+/**
+  * @}
+  */
+
+/** @defgroup TIMEx_Exported_Functions_Group4 Extended Timer Complementary One Pulse functions
+  * @brief    Timer Complementary One Pulse functions
+  *
+@verbatim
+  ==============================================================================
+                ##### Timer Complementary One Pulse functions #####
+  ==============================================================================
+  [..]
+    This section provides functions allowing to:
+    (+) Start the Complementary One Pulse generation.
+    (+) Stop the Complementary One Pulse.
+    (+) Start the Complementary One Pulse and enable interrupts.
+    (+) Stop the Complementary One Pulse and disable interrupts.
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Starts the TIM One Pulse signal generation on the complementary
+  *         output.
+  * @param  htim : TIM One Pulse handle
+  * @param  OutputChannel : TIM Channel to be enabled
+  *          This parameter can be one of the following values:
+  *            @arg TIM_CHANNEL_1: TIM Channel 1 selected
+  *            @arg TIM_CHANNEL_2: TIM Channel 2 selected
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start(TIM_HandleTypeDef *htim, uint32_t OutputChannel)
+  {
+  /* Check the parameters */
+  assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, OutputChannel));
+
+  /* Enable the complementary One Pulse output */
+  TIM_CCxNChannelCmd(htim->Instance, OutputChannel, TIM_CCxN_ENABLE);
+
+  /* Enable the Main Ouput */
+  __HAL_TIM_MOE_ENABLE(htim);
+
+  /* Return function status */
+  return HAL_OK;
+}
+
+/**
+  * @brief  Stops the TIM One Pulse signal generation on the complementary
+  *         output.
+  * @param  htim : TIM One Pulse handle
+  * @param  OutputChannel : TIM Channel to be disabled
+  *          This parameter can be one of the following values:
+  *            @arg TIM_CHANNEL_1: TIM Channel 1 selected
+  *            @arg TIM_CHANNEL_2: TIM Channel 2 selected
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop(TIM_HandleTypeDef *htim, uint32_t OutputChannel)
+{
+
+  /* Check the parameters */
+  assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, OutputChannel));
+
+  /* Disable the complementary One Pulse output */
+  TIM_CCxNChannelCmd(htim->Instance, OutputChannel, TIM_CCxN_DISABLE);
+
+  /* Disable the Main Ouput */
+  __HAL_TIM_MOE_DISABLE(htim);
+
+  /* Disable the Peripheral */
+  __HAL_TIM_DISABLE(htim);
+
+  /* Return function status */
+  return HAL_OK;
+}
+
+/**
+  * @brief  Starts the TIM One Pulse signal generation in interrupt mode on the
+  *         complementary channel.
+  * @param  htim : TIM One Pulse handle
+  * @param  OutputChannel : TIM Channel to be enabled
+  *          This parameter can be one of the following values:
+  *            @arg TIM_CHANNEL_1: TIM Channel 1 selected
+  *            @arg TIM_CHANNEL_2: TIM Channel 2 selected
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start_IT(TIM_HandleTypeDef *htim, uint32_t OutputChannel)
+{
+  /* Check the parameters */
+  assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, OutputChannel));
+
+  /* Enable the TIM Capture/Compare 1 interrupt */
+  __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1);
+
+  /* Enable the TIM Capture/Compare 2 interrupt */
+  __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2);
+
+  /* Enable the complementary One Pulse output */
+  TIM_CCxNChannelCmd(htim->Instance, OutputChannel, TIM_CCxN_ENABLE);
+
+  /* Enable the Main Ouput */
+  __HAL_TIM_MOE_ENABLE(htim);
+
+  /* Return function status */
+  return HAL_OK;
+}
+
+/**
+  * @brief  Stops the TIM One Pulse signal generation in interrupt mode on the
+  *         complementary channel.
+  * @param  htim : TIM One Pulse handle
+  * @param  OutputChannel : TIM Channel to be disabled
+  *          This parameter can be one of the following values:
+  *            @arg TIM_CHANNEL_1: TIM Channel 1 selected
+  *            @arg TIM_CHANNEL_2: TIM Channel 2 selected
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop_IT(TIM_HandleTypeDef *htim, uint32_t OutputChannel)
+{
+  /* Check the parameters */
+  assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, OutputChannel));
+
+  /* Disable the TIM Capture/Compare 1 interrupt */
+  __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1);
+
+  /* Disable the TIM Capture/Compare 2 interrupt */
+  __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2);
+
+  /* Disable the complementary One Pulse output */
+  TIM_CCxNChannelCmd(htim->Instance, OutputChannel, TIM_CCxN_DISABLE);
+
+  /* Disable the Main Ouput */
+  __HAL_TIM_MOE_DISABLE(htim);
+
+  /* Disable the Peripheral */
+  __HAL_TIM_DISABLE(htim);
+
+  /* Return function status */
+  return HAL_OK;
+}
+
+/**
+  * @}
+  */
+
+/** @defgroup TIMEx_Exported_Functions_Group5 Extended Peripheral Control functions
+  * @brief    Peripheral Control functions
+  *
+@verbatim
+  ==============================================================================
+                    ##### Peripheral Control functions #####
+  ==============================================================================
+  [..]
+    This section provides functions allowing to:
+    (+) Configure the commutation event in case of use of the Hall sensor interface.
+      (+) Configure Output channels for OC and PWM mode.
+
+      (+) Configure Complementary channels, break features and dead time.
+      (+) Configure Master synchronization.
+      (+) Configure timer remapping capabilities.
+      (+) Enable or disable channel grouping
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Configure the TIM commutation event sequence.
+  * @note  This function is mandatory to use the commutation event in order to
+  *        update the configuration at each commutation detection on the TRGI input of the Timer,
+  *        the typical use of this feature is with the use of another Timer(interface Timer)
+  *        configured in Hall sensor interface, this interface Timer will generate the
+  *        commutation at its TRGO output (connected to Timer used in this function) each time
+  *        the TI1 of the Interface Timer detect a commutation at its input TI1.
+  * @param  htim: TIM handle
+  * @param  InputTrigger : the Internal trigger corresponding to the Timer Interfacing with the Hall sensor
+  *          This parameter can be one of the following values:
+  *            @arg TIM_TS_ITR0: Internal trigger 0 selected
+  *            @arg TIM_TS_ITR1: Internal trigger 1 selected
+  *            @arg TIM_TS_ITR2: Internal trigger 2 selected
+  *            @arg TIM_TS_ITR3: Internal trigger 3 selected
+  *            @arg TIM_TS_NONE: No trigger is needed
+  * @param  CommutationSource : the Commutation Event source
+  *          This parameter can be one of the following values:
+  *            @arg TIM_COMMUTATION_TRGI: Commutation source is the TRGI of the Interface Timer
+  *            @arg TIM_COMMUTATION_SOFTWARE:  Commutation source is set by software using the COMG bit
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_ConfigCommutationEvent(TIM_HandleTypeDef *htim, uint32_t  InputTrigger, uint32_t  CommutationSource)
+{
+  /* Check the parameters */
+  assert_param(IS_TIM_COMMUTATION_EVENT_INSTANCE(htim->Instance));
+  assert_param(IS_TIM_INTERNAL_TRIGGEREVENT_SELECTION(InputTrigger));
+
+  __HAL_LOCK(htim);
+
+  if ((InputTrigger == TIM_TS_ITR0) || (InputTrigger == TIM_TS_ITR1) ||
+      (InputTrigger == TIM_TS_ITR2) || (InputTrigger == TIM_TS_ITR3))
+  {
+    /* Select the Input trigger */
+    htim->Instance->SMCR &= ~TIM_SMCR_TS;
+    htim->Instance->SMCR |= InputTrigger;
+  }
+
+  /* Select the Capture Compare preload feature */
+  htim->Instance->CR2 |= TIM_CR2_CCPC;
+  /* Select the Commutation event source */
+  htim->Instance->CR2 &= ~TIM_CR2_CCUS;
+  htim->Instance->CR2 |= CommutationSource;
+
+  __HAL_UNLOCK(htim);
+
+  return HAL_OK;
+}
+
+/**
+  * @brief  Configure the TIM commutation event sequence with interrupt.
+  * @note  This function is mandatory to use the commutation event in order to
+  *        update the configuration at each commutation detection on the TRGI input of the Timer,
+  *        the typical use of this feature is with the use of another Timer(interface Timer)
+  *        configured in Hall sensor interface, this interface Timer will generate the
+  *        commutation at its TRGO output (connected to Timer used in this function) each time
+  *        the TI1 of the Interface Timer detect a commutation at its input TI1.
+  * @param  htim: TIM handle
+  * @param  InputTrigger : the Internal trigger corresponding to the Timer Interfacing with the Hall sensor
+  *          This parameter can be one of the following values:
+  *            @arg TIM_TS_ITR0: Internal trigger 0 selected
+  *            @arg TIM_TS_ITR1: Internal trigger 1 selected
+  *            @arg TIM_TS_ITR2: Internal trigger 2 selected
+  *            @arg TIM_TS_ITR3: Internal trigger 3 selected
+  *            @arg TIM_TS_NONE: No trigger is needed
+  * @param  CommutationSource : the Commutation Event source
+  *          This parameter can be one of the following values:
+  *            @arg TIM_COMMUTATION_TRGI: Commutation source is the TRGI of the Interface Timer
+  *            @arg TIM_COMMUTATION_SOFTWARE:  Commutation source is set by software using the COMG bit
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_ConfigCommutationEvent_IT(TIM_HandleTypeDef *htim, uint32_t  InputTrigger, uint32_t  CommutationSource)
+{
+  /* Check the parameters */
+  assert_param(IS_TIM_COMMUTATION_EVENT_INSTANCE(htim->Instance));
+  assert_param(IS_TIM_INTERNAL_TRIGGEREVENT_SELECTION(InputTrigger));
+
+  __HAL_LOCK(htim);
+
+  if ((InputTrigger == TIM_TS_ITR0) || (InputTrigger == TIM_TS_ITR1) ||
+      (InputTrigger == TIM_TS_ITR2) || (InputTrigger == TIM_TS_ITR3))
+  {
+    /* Select the Input trigger */
+    htim->Instance->SMCR &= ~TIM_SMCR_TS;
+    htim->Instance->SMCR |= InputTrigger;
+  }
+
+  /* Select the Capture Compare preload feature */
+  htim->Instance->CR2 |= TIM_CR2_CCPC;
+  /* Select the Commutation event source */
+  htim->Instance->CR2 &= ~TIM_CR2_CCUS;
+  htim->Instance->CR2 |= CommutationSource;
+
+  /* Enable the Commutation Interrupt Request */
+  __HAL_TIM_ENABLE_IT(htim, TIM_IT_COM);
+
+  __HAL_UNLOCK(htim);
+
+  return HAL_OK;
+}
+
+/**
+  * @brief  Configure the TIM commutation event sequence with DMA.
+  * @note  This function is mandatory to use the commutation event in order to
+  *        update the configuration at each commutation detection on the TRGI input of the Timer,
+  *        the typical use of this feature is with the use of another Timer(interface Timer)
+  *        configured in Hall sensor interface, this interface Timer will generate the
+  *        commutation at its TRGO output (connected to Timer used in this function) each time
+  *        the TI1 of the Interface Timer detect a commutation at its input TI1.
+  * @note  The user should configure the DMA in his own software, in This function only the COMDE bit is set
+  * @param  htim: TIM handle
+  * @param  InputTrigger : the Internal trigger corresponding to the Timer Interfacing with the Hall sensor
+  *          This parameter can be one of the following values:
+  *            @arg TIM_TS_ITR0: Internal trigger 0 selected
+  *            @arg TIM_TS_ITR1: Internal trigger 1 selected
+  *            @arg TIM_TS_ITR2: Internal trigger 2 selected
+  *            @arg TIM_TS_ITR3: Internal trigger 3 selected
+  *            @arg TIM_TS_NONE: No trigger is needed
+  * @param  CommutationSource : the Commutation Event source
+  *          This parameter can be one of the following values:
+  *            @arg TIM_COMMUTATION_TRGI: Commutation source is the TRGI of the Interface Timer
+  *            @arg TIM_COMMUTATION_SOFTWARE:  Commutation source is set by software using the COMG bit
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_ConfigCommutationEvent_DMA(TIM_HandleTypeDef *htim, uint32_t  InputTrigger, uint32_t  CommutationSource)
+{
+  /* Check the parameters */
+  assert_param(IS_TIM_COMMUTATION_EVENT_INSTANCE(htim->Instance));
+  assert_param(IS_TIM_INTERNAL_TRIGGEREVENT_SELECTION(InputTrigger));
+
+  __HAL_LOCK(htim);
+
+  if ((InputTrigger == TIM_TS_ITR0) || (InputTrigger == TIM_TS_ITR1) ||
+      (InputTrigger == TIM_TS_ITR2) || (InputTrigger == TIM_TS_ITR3))
+  {
+    /* Select the Input trigger */
+    htim->Instance->SMCR &= ~TIM_SMCR_TS;
+    htim->Instance->SMCR |= InputTrigger;
+  }
+
+  /* Select the Capture Compare preload feature */
+  htim->Instance->CR2 |= TIM_CR2_CCPC;
+  /* Select the Commutation event source */
+  htim->Instance->CR2 &= ~TIM_CR2_CCUS;
+  htim->Instance->CR2 |= CommutationSource;
+
+  /* Enable the Commutation DMA Request */
+  /* Set the DMA Commutation Callback */
+  htim->hdma[TIM_DMA_ID_COMMUTATION]->XferCpltCallback = TIMEx_DMACommutationCplt;
+  /* Set the DMA error callback */
+  htim->hdma[TIM_DMA_ID_COMMUTATION]->XferErrorCallback = TIM_DMAError;
+
+  /* Enable the Commutation DMA Request */
+  __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_COM);
+
+  __HAL_UNLOCK(htim);
+
+  return HAL_OK;
+}
+
+/**
+  * @brief  Configures the TIM in master mode.
+  * @param  htim: TIM handle.
+  * @param  sMasterConfig: pointer to a TIM_MasterConfigTypeDef structure that
+  *         contains the selected trigger output (TRGO) and the Master/Slave
+  *         mode.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_MasterConfigSynchronization(TIM_HandleTypeDef *htim,
+                                                      TIM_MasterConfigTypeDef * sMasterConfig)
+{
+  uint32_t tmpcr2;
+  uint32_t tmpsmcr;
+
+  /* Check the parameters */
+  assert_param(IS_TIM_SYNCHRO_INSTANCE(htim->Instance));
+  assert_param(IS_TIM_TRGO_SOURCE(sMasterConfig->MasterOutputTrigger));
+  assert_param(IS_TIM_MSM_STATE(sMasterConfig->MasterSlaveMode));
+
+  /* Check input state */
+  __HAL_LOCK(htim);
+
+ /* Get the TIMx CR2 register value */
+  tmpcr2 = htim->Instance->CR2;
+
+  /* Get the TIMx SMCR register value */
+  tmpsmcr = htim->Instance->SMCR;
+
+  /* If the timer supports ADC synchronization through TRGO2, set the master mode selection 2 */
+  if (IS_TIM_TRGO2_INSTANCE(htim->Instance))
+  {
+    /* Check the parameters */
+    assert_param(IS_TIM_TRGO2_SOURCE(sMasterConfig->MasterOutputTrigger2));
+
+    /* Clear the MMS2 bits */
+    tmpcr2 &= ~TIM_CR2_MMS2;
+    /* Select the TRGO2 source*/
+    tmpcr2 |= sMasterConfig->MasterOutputTrigger2;
+  }
+
+  /* Reset the MMS Bits */
+  tmpcr2 &= ~TIM_CR2_MMS;
+  /* Select the TRGO source */
+  tmpcr2 |=  sMasterConfig->MasterOutputTrigger;
+
+  /* Reset the MSM Bit */
+  tmpsmcr &= ~TIM_SMCR_MSM;
+  /* Set master mode */
+  tmpsmcr |= sMasterConfig->MasterSlaveMode;
+
+  /* Update TIMx CR2 */
+  htim->Instance->CR2 = tmpcr2;
+
+  /* Update TIMx SMCR */
+  htim->Instance->SMCR = tmpsmcr;
+
+  __HAL_UNLOCK(htim);
+
+  return HAL_OK;
+}
+
+/**
+  * @brief   Configures the Break feature, dead time, Lock level, OSSI/OSSR State
+  *         and the AOE(automatic output enable).
+  * @param  htim: TIM handle
+  * @param  sBreakDeadTimeConfig: pointer to a TIM_ConfigBreakDeadConfigTypeDef structure that
+  *         contains the BDTR Register configuration  information for the TIM peripheral.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_ConfigBreakDeadTime(TIM_HandleTypeDef *htim,
+                                                TIM_BreakDeadTimeConfigTypeDef * sBreakDeadTimeConfig)
+{
+  uint32_t tmpbdtr = 0;
+  
+  /* Check the parameters */
+  assert_param(IS_TIM_BREAK_INSTANCE(htim->Instance));
+  assert_param(IS_TIM_OSSR_STATE(sBreakDeadTimeConfig->OffStateRunMode));
+  assert_param(IS_TIM_OSSI_STATE(sBreakDeadTimeConfig->OffStateIDLEMode));
+  assert_param(IS_TIM_LOCK_LEVEL(sBreakDeadTimeConfig->LockLevel));
+  assert_param(IS_TIM_DEADTIME(sBreakDeadTimeConfig->DeadTime));
+  assert_param(IS_TIM_BREAK_STATE(sBreakDeadTimeConfig->BreakState));
+  assert_param(IS_TIM_BREAK_POLARITY(sBreakDeadTimeConfig->BreakPolarity));
+  assert_param(IS_TIM_BREAK_FILTER(sBreakDeadTimeConfig->BreakFilter));
+  assert_param(IS_TIM_AUTOMATIC_OUTPUT_STATE(sBreakDeadTimeConfig->AutomaticOutput));
+  
+  /* Check input state */
+  __HAL_LOCK(htim);
+  
+  /* Set the Lock level, the Break enable Bit and the Polarity, the OSSR State,
+  the OSSI State, the dead time value and the Automatic Output Enable Bit */
+  
+  /* Set the BDTR bits */
+  MODIFY_REG(tmpbdtr, TIM_BDTR_DTG, sBreakDeadTimeConfig->DeadTime);
+  MODIFY_REG(tmpbdtr, TIM_BDTR_LOCK, sBreakDeadTimeConfig->LockLevel);
+  MODIFY_REG(tmpbdtr, TIM_BDTR_OSSI, sBreakDeadTimeConfig->OffStateIDLEMode);
+  MODIFY_REG(tmpbdtr, TIM_BDTR_OSSR, sBreakDeadTimeConfig->OffStateRunMode);
+  MODIFY_REG(tmpbdtr, TIM_BDTR_BKE, sBreakDeadTimeConfig->BreakState);
+  MODIFY_REG(tmpbdtr, TIM_BDTR_BKP, sBreakDeadTimeConfig->BreakPolarity);
+  MODIFY_REG(tmpbdtr, TIM_BDTR_AOE, sBreakDeadTimeConfig->AutomaticOutput);
+  MODIFY_REG(tmpbdtr, TIM_BDTR_MOE, sBreakDeadTimeConfig->AutomaticOutput);
+  MODIFY_REG(tmpbdtr, TIM_BDTR_BKF, (sBreakDeadTimeConfig->BreakFilter << BDTR_BKF_SHIFT));
+  
+  if (IS_TIM_BKIN2_INSTANCE(htim->Instance))
+  {
+    assert_param(IS_TIM_BREAK2_STATE(sBreakDeadTimeConfig->Break2State));
+    assert_param(IS_TIM_BREAK2_POLARITY(sBreakDeadTimeConfig->Break2Polarity));
+    assert_param(IS_TIM_BREAK_FILTER(sBreakDeadTimeConfig->Break2Filter));
+    
+    /* Set the BREAK2 input related BDTR bits */
+    MODIFY_REG(tmpbdtr, TIM_BDTR_BK2F, (sBreakDeadTimeConfig->Break2Filter << BDTR_BK2F_SHIFT));
+    MODIFY_REG(tmpbdtr, TIM_BDTR_BK2E, sBreakDeadTimeConfig->Break2State);
+    MODIFY_REG(tmpbdtr, TIM_BDTR_BK2P, sBreakDeadTimeConfig->Break2Polarity);
+  }
+  
+  /* Set TIMx_BDTR */
+  htim->Instance->BDTR = tmpbdtr;
+  
+  __HAL_UNLOCK(htim);
+
+  return HAL_OK;
+}
+
+/**
+  * @brief  Configures the break input source.
+  * @param  htim: TIM handle.
+  * @param  BreakInput: Break input to configure
+  *          This parameter can be one of the following values:
+  *            @arg TIM_BREAKINPUT_BRK: Timer break input
+  *            @arg TIM_BREAKINPUT_BRK2: Timer break 2 input
+  * @param  sBreakInputConfig: Break input source configuration
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_ConfigBreakInput(TIM_HandleTypeDef *htim,
+                                             uint32_t BreakInput,
+                                             TIMEx_BreakInputConfigTypeDef *sBreakInputConfig)
+
+{
+  uint32_t tmporx = 0;
+  uint32_t bkin_enable_mask = 0;
+  uint32_t bkin_polarity_mask = 0;
+  uint32_t bkin_enable_bitpos = 0;
+  uint32_t bkin_polarity_bitpos = 0;
+
+  /* Check the parameters */
+  assert_param(IS_TIM_BREAK_INSTANCE(htim->Instance));
+  assert_param(IS_TIM_BREAKINPUT(BreakInput));
+  assert_param(IS_TIM_BREAKINPUTSOURCE(sBreakInputConfig->Source));
+  assert_param(IS_TIM_BREAKINPUTSOURCE_STATE(sBreakInputConfig->Enable));
+
+#if defined (STM32L451xx) || defined (STM32L452xx) || defined (STM32L462xx) || defined (STM32L471xx) || \
+    defined (STM32L475xx) || defined (STM32L476xx) || defined (STM32L485xx) || defined (STM32L486xx)
+  if (sBreakInputConfig->Source != TIM_BREAKINPUTSOURCE_DFSDM1)
+  {
+    assert_param(IS_TIM_BREAKINPUTSOURCE_POLARITY(sBreakInputConfig->Polarity));
+  }
+#else
+   assert_param(IS_TIM_BREAKINPUTSOURCE_POLARITY(sBreakInputConfig->Polarity));
+#endif /* STM32L451xx || STM32L452xx || STM32L462xx || STM32L471xx */
+       /* STM32L475xx || STM32L476xx || STM32L485xx || STM32L486xx */
+  
+  /* Check input state */
+  __HAL_LOCK(htim);
+  
+  switch(sBreakInputConfig->Source)
+  {
+  case TIM_BREAKINPUTSOURCE_BKIN:
+    {
+      bkin_enable_mask = TIM1_OR2_BKINE;
+      bkin_enable_bitpos = 0;
+      bkin_polarity_mask = TIM1_OR2_BKINP;
+      bkin_polarity_bitpos = 9;
+    }
+    break;
+  case TIM_BREAKINPUTSOURCE_COMP1:
+    {
+      bkin_enable_mask = TIM1_OR2_BKCMP1E;
+      bkin_enable_bitpos = 1;
+      bkin_polarity_mask = TIM1_OR2_BKCMP1P;
+      bkin_polarity_bitpos = 10;
+    }
+    break;
+  case TIM_BREAKINPUTSOURCE_COMP2:
+    {
+      bkin_enable_mask = TIM1_OR2_BKCMP2E;
+      bkin_enable_bitpos = 2;
+      bkin_polarity_mask = TIM1_OR2_BKCMP2P;
+      bkin_polarity_bitpos = 11;
+    }
+    break;
+
+#if defined (STM32L451xx) || defined (STM32L452xx) || defined (STM32L462xx) || defined (STM32L471xx) || \
+    defined (STM32L475xx) || defined (STM32L476xx) || defined (STM32L485xx) || defined (STM32L486xx)
+  case TIM_BREAKINPUTSOURCE_DFSDM1:
+    {
+      bkin_enable_mask = TIM1_OR2_BKDF1BK0E;
+      bkin_enable_bitpos = 8;
+    }
+    break;    
+#endif /* STM32L451xx || STM32L452xx || STM32L462xx || STM32L471xx */
+       /* STM32L475xx || STM32L476xx || STM32L485xx || STM32L486xx */
+
+  default:
+    break;
+  }
+  
+  switch(BreakInput)
+  {
+    case TIM_BREAKINPUT_BRK:
+      {
+        /* Get the TIMx_OR2 register value */
+        tmporx = htim->Instance->OR2;
+        
+        /* Enable the break input */
+        tmporx &= ~bkin_enable_mask;
+        tmporx |= (sBreakInputConfig->Enable << bkin_enable_bitpos) & bkin_enable_mask;
+        
+        /* Set the break input polarity */
+#if defined (STM32L451xx) || defined (STM32L452xx) || defined (STM32L462xx) || defined (STM32L471xx) || \
+    defined (STM32L475xx) || defined (STM32L476xx) || defined (STM32L485xx) || defined (STM32L486xx)
+        if (sBreakInputConfig->Source != TIM_BREAKINPUTSOURCE_DFSDM1)
+#endif /* STM32L451xx || STM32L452xx || STM32L462xx || STM32L471xx */
+       /* STM32L475xx || STM32L476xx || STM32L485xx || STM32L486xx */
+        {
+          tmporx &= ~bkin_polarity_mask;
+          tmporx |= (sBreakInputConfig->Polarity << bkin_polarity_bitpos) & bkin_polarity_mask;
+        }
+        
+        /* Set TIMx_OR2 */
+        htim->Instance->OR2 = tmporx;        
+      }
+        break;
+    case TIM_BREAKINPUT_BRK2:
+      {
+        /* Get the TIMx_OR3 register value */
+        tmporx = htim->Instance->OR3;
+        
+        /* Enable the break input */
+        tmporx &= ~bkin_enable_mask;
+        tmporx |= (sBreakInputConfig->Enable << bkin_enable_bitpos) & bkin_enable_mask;
+        
+        /* Set the break input polarity */
+#if defined (STM32L451xx) || defined (STM32L452xx) || defined (STM32L462xx) || defined (STM32L471xx) || \
+    defined (STM32L475xx) || defined (STM32L476xx) || defined (STM32L485xx) || defined (STM32L486xx)
+        if (sBreakInputConfig->Source != TIM_BREAKINPUTSOURCE_DFSDM1)
+#endif /* STM32L451xx || STM32L452xx || STM32L462xx || STM32L471xx */
+       /* STM32L475xx || STM32L476xx || STM32L485xx || STM32L486xx */
+        {
+          tmporx &= ~bkin_polarity_mask;
+          tmporx |= (sBreakInputConfig->Polarity << bkin_polarity_bitpos) & bkin_polarity_mask;
+        }
+        
+        /* Set TIMx_OR3 */
+        htim->Instance->OR3 = tmporx;        
+      }
+      break;    
+  default:
+    break;
+  }
+  
+  __HAL_UNLOCK(htim);
+
+  return HAL_OK;
+}
+
+/**
+  * @brief  Configures the TIMx Remapping input capabilities.
+  * @param  htim: TIM handle.
+  * @param  Remap: specifies the TIM remapping source.
+  *
+  @if STM32L486xx
+  *         For TIM1, the parameter is a combination of 4 fields (field1 | field2 | field3 | field4):
+  *
+  *                   field1 can have the following values:
+  *            @arg TIM_TIM1_ETR_ADC1_NONE:           TIM1_ETR is not connected to any ADC1 AWD (analog watchdog)
+  *            @arg TIM_TIM1_ETR_ADC1_AWD1:           TIM1_ETR is connected to ADC1 AWD1
+  *            @arg TIM_TIM1_ETR_ADC1_AWD2:           TIM1_ETR is connected to ADC1 AWD2
+  *            @arg TIM_TIM1_ETR_ADC1_AWD3:           TIM1_ETR is connected to ADC1 AWD3
+  *
+  *                   field2 can have the following values:
+  *            @arg TIM_TIM1_ETR_ADC3_NONE:           TIM1_ETR is not connected to any ADC3 AWD (analog watchdog)
+  *            @arg TIM_TIM1_ETR_ADC3_AWD1:           TIM1_ETR is connected to ADC3 AWD1
+  *            @arg TIM_TIM1_ETR_ADC3_AWD2:           TIM1_ETR is connected to ADC3 AWD2
+  *            @arg TIM_TIM1_ETR_ADC3_AWD3:           TIM1_ETR is connected to ADC3 AWD3
+  *
+  *                   field3 can have the following values:
+  *            @arg TIM_TIM1_TI1_GPIO:                TIM1 TI1 is connected to GPIO
+  *            @arg TIM_TIM1_TI1_COMP1:               TIM1 TI1 is connected to COMP1 output
+  *
+  *                   field4 can have the following values:
+  *            @arg TIM_TIM1_ETR_COMP1:               TIM1_ETR is connected to COMP1 output
+  *            @arg TIM_TIM1_ETR_COMP2:               TIM1_ETR is connected to COMP2 output
+  *            @note  When field4 is set to TIM_TIM1_ETR_COMP1 or TIM_TIM1_ETR_COMP2 field1 and field2 values are not significant 
+  @endif
+  @if STM32L443xx
+  *         For TIM1, the parameter is a combination of 3 fields (field1 | field2 | field3):
+  *
+  *                   field1 can have the following values:
+  *            @arg TIM_TIM1_ETR_ADC1_NONE:           TIM1_ETR is not connected to any ADC1 AWD (analog watchdog)
+  *            @arg TIM_TIM1_ETR_ADC1_AWD1:           TIM1_ETR is connected to ADC1 AWD1
+  *            @arg TIM_TIM1_ETR_ADC1_AWD2:           TIM1_ETR is connected to ADC1 AWD2
+  *            @arg TIM_TIM1_ETR_ADC1_AWD3:           TIM1_ETR is connected to ADC1 AWD3
+  *
+  *                   field2 can have the following values:
+  *            @arg TIM_TIM1_TI1_GPIO:                TIM1 TI1 is connected to GPIO
+  *            @arg TIM_TIM1_TI1_COMP1:               TIM1 TI1 is connected to COMP1 output
+  *
+  *                   field3 can have the following values:
+  *            @arg TIM_TIM1_ETR_COMP1:               TIM1_ETR is connected to COMP1 output
+  *            @arg TIM_TIM1_ETR_COMP2:               TIM1_ETR is connected to COMP2 output
+  *
+  *            @note  When field3 is set to TIM_TIM1_ETR_COMP1 or TIM_TIM1_ETR_COMP2 field1 values is not significant 
+  *
+  @endif
+  @if STM32L486xx
+  *         For TIM2, the parameter is a combination of 3 fields (field1 | field2 | field3):
+  *
+  *                   field1 can have the following values:
+  *            @arg TIM_TIM2_ITR1_TIM8_TRGO:          TIM2_ITR1 is connected to TIM8_TRGO
+  *            @arg TIM_TIM2_ITR1_OTG_FS_SOF:         TIM2_ITR1 is connected to OTG_FS SOF
+  *
+  *                   field2 can have the following values:
+  *            @arg TIM_TIM2_ETR_GPIO:                TIM2_ETR is connected to GPIO
+  *            @arg TIM_TIM2_ETR_LSE:                 TIM2_ETR is connected to LSE
+  *            @arg TIM_TIM2_ETR_COMP1:               TIM2_ETR is connected to COMP1 output
+  *            @arg TIM_TIM2_ETR_COMP2:               TIM2_ETR is connected to COMP2 output
+  *
+  *                   field3 can have the following values:
+  *            @arg TIM_TIM2_TI4_GPIO:                TIM2 TI4 is connected to GPIO
+  *            @arg TIM_TIM2_TI4_COMP1:               TIM2 TI4 is connected to COMP1 output
+  *            @arg TIM_TIM2_TI4_COMP2:               TIM2 TI4 is connected to COMP2 output
+  *            @arg TIM_TIM2_TI4_COMP1_COMP2:         TIM2 TI4 is connected to logical OR between COMP1 and COMP2 output
+  @endif
+  @if STM32L443xx
+  *         For TIM2, the parameter is a combination of 3 fields (field1 | field2 | field3):
+  *
+  *                   field1 can have the following values:
+  *            @arg TIM_TIM2_ITR1_NONE:               No internal trigger on TIM2_ITR1
+  *            @arg TIM_TIM2_ITR1_USB_SOF:            TIM2_ITR1 is connected to USB SOF
+  *
+  *                   field2 can have the following values:
+  *            @arg TIM_TIM2_ETR_GPIO:                TIM2_ETR is connected to GPIO
+  *            @arg TIM_TIM2_ETR_LSE:                 TIM2_ETR is connected to LSE
+  *            @arg TIM_TIM2_ETR_COMP1:               TIM2_ETR is connected to COMP1 output
+  *            @arg TIM_TIM2_ETR_COMP2:               TIM2_ETR is connected to COMP2 output
+  *
+  *                   field3 can have the following values:
+  *            @arg TIM_TIM2_TI4_GPIO:                TIM2 TI4 is connected to GPIO
+  *            @arg TIM_TIM2_TI4_COMP1:               TIM2 TI4 is connected to COMP1 output
+  *            @arg TIM_TIM2_TI4_COMP2:               TIM2 TI4 is connected to COMP2 output
+  *            @arg TIM_TIM2_TI4_COMP1_COMP2:         TIM2 TI4 is connected to logical OR between COMP1 and COMP2 output
+  *
+  @endif
+  @if STM32L486xx
+  *         For TIM3, the parameter is a combination 2 fields(field1 | field2):
+  *
+  *                   field1 can have the following values:
+  *            @arg TIM_TIM3_TI1_GPIO:                TIM3 TI1 is connected to GPIO
+  *            @arg TIM_TIM3_TI1_COMP1:               TIM3 TI1 is connected to COMP1 output
+  *            @arg TIM_TIM3_TI1_COMP2:               TIM3 TI1 is connected to COMP2 output
+  *            @arg TIM_TIM3_TI1_COMP1_COMP2:         TIM3 TI1 is connected to logical OR between COMP1 and COMP2 output
+  *
+  *                   field2 can have the following values:
+  *            @arg TIM_TIM3_ETR_GPIO:                TIM3_ETR is connected to GPIO
+  *            @arg TIM_TIM3_ETR_COMP1:               TIM3_ETR is connected to COMP1 output
+  *
+  @endif
+  @if STM32L486xx
+  *         For TIM8, the parameter is a combination of 3 fields (field1 | field2 | field3):
+  *
+  *                   field1 can have the following values:
+  *            @arg TIM_TIM8_ETR_ADC2_NONE:          TIM8_ETR is not connected to any ADC2 AWD (analog watchdog)
+  *            @arg TIM_TIM8_ETR_ADC2_AWD1:          TIM8_ETR is connected to ADC2 AWD1
+  *            @arg TIM_TIM8_ETR_ADC2_AWD2:          TIM8_ETR is connected to ADC2 AWD2
+  *            @arg TIM_TIM8_ETR_ADC2_AWD3:          TIM8_ETR is connected to ADC2 AWD3
+  *
+  *                   field2 can have the following values:
+  *            @arg TIM_TIM8_ETR_ADC3_NONE:          TIM8_ETR is not connected to any ADC3 AWD (analog watchdog)
+  *            @arg TIM_TIM8_ETR_ADC3_AWD1:          TIM8_ETR is connected to ADC3 AWD1
+  *            @arg TIM_TIM8_ETR_ADC3_AWD2:          TIM8_ETR is connected to ADC3 AWD2
+  *            @arg TIM_TIM8_ETR_ADC3_AWD3:          TIM8_ETR is connected to ADC3 AWD3
+  *
+  *                   field3 can have the following values:
+  *            @arg TIM_TIM8_TI1_GPIO:               TIM8 TI1 is connected to GPIO
+  *            @arg TIM_TIM8_TI1_COMP2:              TIM8 TI1 is connected to COMP2 output
+  *
+  *                   field4 can have the following values:
+  *            @arg TIM_TIM8_ETR_COMP1:               TIM8_ETR is connected to COMP1 output
+  *            @arg TIM_TIM8_ETR_COMP2:               TIM8_ETR is connected to COMP2 output
+  *            @note  When field4 is set to TIM_TIM8_ETR_COMP1 or TIM_TIM8_ETR_COMP2 field1 and field2 values are not significant 
+  *
+  @endif
+  *         For TIM15, the parameter is a combination of 3 fields (field1 | field2):
+  *
+  *                   field1 can have the following values:
+  *            @arg TIM_TIM15_TI1_GPIO:              TIM15 TI1 is connected to GPIO
+  *            @arg TIM_TIM15_TI1_LSE:               TIM15 TI1 is connected to LSE
+  *
+  *                   field2 can have the following values:
+  *            @arg TIM_TIM15_ENCODERMODE_NONE:      No redirection 
+  *            @arg TIM_TIM15_ENCODERMODE_TIM2:      TIM2 IC1 and TIM2 IC2 are connected to TIM15 IC1 and TIM15 IC2 respectively
+  *            @arg TIM_TIM15_ENCODERMODE_TIM3:      TIM3 IC1 and TIM3 IC2 are connected to TIM15 IC1 and TIM15 IC2 respectively
+  *            @arg TIM_TIM15_ENCODERMODE_TIM4:      TIM4 IC1 and TIM4 IC2 are connected to TIM15 IC1 and TIM15 IC2 respectively
+  *
+  @if STM32L486xx
+  *            @arg TIM_TIM16_TI1_GPIO:              TIM16 TI1 is connected to GPIO
+  *            @arg TIM_TIM16_TI1_LSI:               TIM16 TI1 is connected to LSI
+  *            @arg TIM_TIM16_TI1_LSE:               TIM16 TI1 is connected to LSE
+  *            @arg TIM_TIM16_TI1_RTC:               TIM16 TI1 is connected to RTC wakeup interrupt
+  *
+  @endif
+  @if STM32L443xx
+  *         For TIM16, the parameter can have the following values:
+  *            @arg TIM_TIM16_TI1_GPIO:              TIM16 TI1 is connected to GPIO
+  *            @arg TIM_TIM16_TI1_LSI:               TIM16 TI1 is connected to LSI
+  *            @arg TIM_TIM16_TI1_LSE:               TIM16 TI1 is connected to LSE
+  *            @arg TIM_TIM16_TI1_RTC:               TIM16 TI1 is connected to RTC wakeup interrupt
+  *            @arg TIM_TIM16_TI1_MSI:               TIM16 TI1 is connected to MSI  (contraints: MSI clock < 1/4 TIM APB clock)
+  *            @arg TIM_TIM16_TI1_HSE_32:            TIM16 TI1 is connected to HSE div 32  (note that HSE div 32 must be selected as RTC clock source)
+  *            @arg TIM_TIM16_TI1_MCO:               TIM16 TI1 is connected to MCO
+  *
+  @endif
+  @if STM32L486xx
+  *         For TIM17, the parameter can have the following values:
+  *            @arg TIM_TIM17_TI1_GPIO:              TIM17 TI1 is connected to GPIO
+  *            @arg TIM_TIM17_TI1_MSI:               TIM17 TI1 is connected to MSI  (contraints: MSI clock < 1/4 TIM APB clock)
+  *            @arg TIM_TIM17_TI1_HSE_32:            TIM17 TI1 is connected to HSE div 32
+  *            @arg TIM_TIM17_TI1_MCO:               TIM17 TI1 is connected to MCO
+  @endif
+  *
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_RemapConfig(TIM_HandleTypeDef *htim, uint32_t Remap)
+{
+  uint32_t tmpor1 = 0;
+  uint32_t tmpor2 = 0;
+  
+  __HAL_LOCK(htim);
+
+  /* Check parameters */
+  assert_param(IS_TIM_REMAP_INSTANCE(htim->Instance));
+  assert_param(IS_TIM_REMAP(Remap));
+  
+  /* Set ETR_SEL bit field (if required) */
+  if (IS_TIM_ETRSEL_INSTANCE(htim->Instance))
+  {
+    tmpor2 = htim->Instance->OR2;
+    tmpor2 &= ~TIMx_ETRSEL_MASK;
+    tmpor2 |= (Remap & TIMx_ETRSEL_MASK);
+    
+    /* Set TIMx_OR2 */
+    htim->Instance->OR2 = tmpor2;        
+  }
+  
+  /* Set other remapping capabilities */
+  tmpor1 = Remap;
+  tmpor1 &= ~TIMx_ETRSEL_MASK;
+
+  /* Set TIMx_OR1 */
+  htim->Instance->OR1 = Remap;
+  
+  /* Set TIMx_OR1 */
+  htim->Instance->OR1 = tmpor1;        
+  
+  htim->State = HAL_TIM_STATE_READY;
+
+  __HAL_UNLOCK(htim);
+
+  return HAL_OK;
+}
+
+/**
+  * @brief  Group channel 5 and channel 1, 2 or 3
+  * @param  htim: TIM handle.
+  * @param  Channels: specifies the reference signal(s) the OC5REF is combined with.
+  *         This parameter can be any combination of the following values:
+  *         TIM_GROUPCH5_NONE: No effect of OC5REF on OC1REFC, OC2REFC and OC3REFC
+  *         TIM_GROUPCH5_OC1REFC: OC1REFC is the logical AND of OC1REFC and OC5REF
+  *         TIM_GROUPCH5_OC2REFC: OC2REFC is the logical AND of OC2REFC and OC5REF
+  *         TIM_GROUPCH5_OC3REFC: OC3REFC is the logical AND of OC3REFC and OC5REF
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_TIMEx_GroupChannel5(TIM_HandleTypeDef *htim, uint32_t Channels)
+{
+  /* Check parameters */
+  assert_param(IS_TIM_COMBINED3PHASEPWM_INSTANCE(htim->Instance));
+  assert_param(IS_TIM_GROUPCH5(Channels));
+
+  /* Process Locked */
+  __HAL_LOCK(htim);
+
+  htim->State = HAL_TIM_STATE_BUSY;
+
+  /* Clear GC5Cx bit fields */
+  htim->Instance->CCR5 &= ~(TIM_CCR5_GC5C3|TIM_CCR5_GC5C2|TIM_CCR5_GC5C1);
+
+  /* Set GC5Cx bit fields */
+  htim->Instance->CCR5 |= Channels;
+
+  htim->State = HAL_TIM_STATE_READY;
+
+  __HAL_UNLOCK(htim);
+
+  return HAL_OK;
+}
+
+/**
+  * @}
+  */
+
+/** @defgroup TIMEx_Exported_Functions_Group6 Extended Callbacks functions
+  * @brief    Extended Callbacks functions
+  *
+@verbatim
+  ==============================================================================
+                    ##### Extended Callbacks functions #####
+  ==============================================================================
+  [..]
+    This section provides Extended TIM callback functions:
+    (+) Timer Commutation callback
+    (+) Timer Break callback
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Hall commutation changed callback in non-blocking mode
+  * @param  htim : TIM handle
+  * @retval None
+  */
+__weak void HAL_TIMEx_CommutationCallback(TIM_HandleTypeDef *htim)
+{
+  /* Prevent unused argument(s) compilation warning */
+  UNUSED(htim);
+
+  /* NOTE : This function should not be modified, when the callback is needed,
+            the HAL_TIMEx_CommutationCallback could be implemented in the user file
+   */
+}
+
+/**
+  * @brief  Hall Break detection callback in non-blocking mode
+  * @param  htim : TIM handle
+  * @retval None
+  */
+__weak void HAL_TIMEx_BreakCallback(TIM_HandleTypeDef *htim)
+{
+  /* Prevent unused argument(s) compilation warning */
+  UNUSED(htim);
+
+  /* NOTE : This function should not be modified, when the callback is needed,
+            the HAL_TIMEx_BreakCallback could be implemented in the user file
+   */
+}
+
+/**
+  * @}
+  */
+
+/** @defgroup TIMEx_Exported_Functions_Group7 Extended Peripheral State functions
+  * @brief    Extended Peripheral State functions
+  *
+@verbatim
+  ==============================================================================
+                ##### Extended Peripheral State functions #####
+  ==============================================================================
+  [..]
+    This subsection permits to get in run-time the status of the peripheral
+    and the data flow.
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Return the TIM Hall Sensor interface handle state.
+  * @param  htim: TIM Hall Sensor handle
+  * @retval HAL state
+  */
+HAL_TIM_StateTypeDef HAL_TIMEx_HallSensor_GetState(TIM_HandleTypeDef *htim)
+{
+  return htim->State;
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @brief  TIM DMA Commutation callback.
+  * @param  hdma : pointer to DMA handle.
+  * @retval None
+  */
+void TIMEx_DMACommutationCplt(DMA_HandleTypeDef *hdma)
+{
+  TIM_HandleTypeDef* htim = ( TIM_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
+
+  htim->State= HAL_TIM_STATE_READY;
+
+  HAL_TIMEx_CommutationCallback(htim);
+}
+
+/**
+  * @brief  Enables or disables the TIM Capture Compare Channel xN.
+  * @param  TIMx to select the TIM peripheral
+  * @param  Channel: specifies the TIM Channel
+  *          This parameter can be one of the following values:
+  *            @arg TIM_Channel_1: TIM Channel 1
+  *            @arg TIM_Channel_2: TIM Channel 2
+  *            @arg TIM_Channel_3: TIM Channel 3
+  * @param  ChannelNState: specifies the TIM Channel CCxNE bit new state.
+  *          This parameter can be: TIM_CCxN_ENABLE or TIM_CCxN_Disable.
+  * @retval None
+  */
+static void TIM_CCxNChannelCmd(TIM_TypeDef* TIMx, uint32_t Channel, uint32_t ChannelNState)
+{
+  uint32_t tmp = 0;
+
+  tmp = TIM_CCER_CC1NE << Channel;
+
+  /* Reset the CCxNE Bit */
+  TIMx->CCER &=  ~tmp;
+
+  /* Set or reset the CCxNE Bit */
+  TIMx->CCER |=  (uint32_t)(ChannelNState << Channel);
+}
+
+/**
+  * @}
+  */
+
+#endif /* HAL_TIM_MODULE_ENABLED */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/