Mercurial > pub > halpp
view l476rg/Drivers/STM32L4xx_HAL_Driver/Inc/stm32l4xx_hal_rcc.h @ 0:32a3b1785697
a rough draft of Hardware Abstraction Layer for C++
STM32L476RG drivers
| author | cin |
|---|---|
| date | Thu, 12 Jan 2017 02:45:43 +0300 |
| parents | |
| children |
line wrap: on
line source
/** ****************************************************************************** * @file stm32l4xx_hal_rcc.h * @author MCD Application Team * @version V1.6.0 * @date 28-October-2016 * @brief Header file of RCC HAL module. ****************************************************************************** * @attention * * <h2><center>© COPYRIGHT(c) 2016 STMicroelectronics</center></h2> * * Redistribution and use in source and binary forms, with or without modification, * are permitted provided that the following conditions are met: * 1. Redistributions of source code must retain the above copyright notice, * this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright notice, * this list of conditions and the following disclaimer in the documentation * and/or other materials provided with the distribution. * 3. Neither the name of STMicroelectronics nor the names of its contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * ****************************************************************************** */ /* Define to prevent recursive inclusion -------------------------------------*/ #ifndef __STM32L4xx_HAL_RCC_H #define __STM32L4xx_HAL_RCC_H #ifdef __cplusplus extern "C" { #endif /* Includes ------------------------------------------------------------------*/ #include "stm32l4xx_hal_def.h" /** @addtogroup STM32L4xx_HAL_Driver * @{ */ /** @addtogroup RCC * @{ */ /* Exported types ------------------------------------------------------------*/ /** @defgroup RCC_Exported_Types RCC Exported Types * @{ */ /** * @brief RCC PLL configuration structure definition */ typedef struct { uint32_t PLLState; /*!< The new state of the PLL. This parameter can be a value of @ref RCC_PLL_Config */ uint32_t PLLSource; /*!< RCC_PLLSource: PLL entry clock source. This parameter must be a value of @ref RCC_PLL_Clock_Source */ uint32_t PLLM; /*!< PLLM: Division factor for PLL VCO input clock. This parameter must be a number between Min_Data = 1 and Max_Data = 8 */ uint32_t PLLN; /*!< PLLN: Multiplication factor for PLL VCO output clock. This parameter must be a number between Min_Data = 8 and Max_Data = 86 */ uint32_t PLLP; /*!< PLLP: Division factor for SAI clock. This parameter must be a value of @ref RCC_PLLP_Clock_Divider */ uint32_t PLLQ; /*!< PLLQ: Division factor for SDMMC1, RNG and USB clocks. This parameter must be a value of @ref RCC_PLLQ_Clock_Divider */ uint32_t PLLR; /*!< PLLR: Division for the main system clock. User have to set the PLLR parameter correctly to not exceed max frequency 80MHZ. This parameter must be a value of @ref RCC_PLLR_Clock_Divider */ }RCC_PLLInitTypeDef; /** * @brief RCC Internal/External Oscillator (HSE, HSI, MSI, LSE and LSI) configuration structure definition */ typedef struct { uint32_t OscillatorType; /*!< The oscillators to be configured. This parameter can be a value of @ref RCC_Oscillator_Type */ uint32_t HSEState; /*!< The new state of the HSE. This parameter can be a value of @ref RCC_HSE_Config */ uint32_t LSEState; /*!< The new state of the LSE. This parameter can be a value of @ref RCC_LSE_Config */ uint32_t HSIState; /*!< The new state of the HSI. This parameter can be a value of @ref RCC_HSI_Config */ uint32_t HSICalibrationValue; /*!< The calibration trimming value (default is RCC_HSICALIBRATION_DEFAULT). This parameter must be a number between Min_Data = 0x00 and Max_Data = 0x1F on STM32L43x/STM32L44x/STM32L47x/STM32L48x devices. This parameter must be a number between Min_Data = 0x00 and Max_Data = 0x7F on the other devices */ uint32_t LSIState; /*!< The new state of the LSI. This parameter can be a value of @ref RCC_LSI_Config */ uint32_t MSIState; /*!< The new state of the MSI. This parameter can be a value of @ref RCC_MSI_Config */ uint32_t MSICalibrationValue; /*!< The calibration trimming value (default is RCC_MSICALIBRATION_DEFAULT). This parameter must be a number between Min_Data = 0x00 and Max_Data = 0xFF */ uint32_t MSIClockRange; /*!< The MSI frequency range. This parameter can be a value of @ref RCC_MSI_Clock_Range */ uint32_t HSI48State; /*!< The new state of the HSI48 (only applicable to STM32L43x/STM32L44x/STM32L45x/STM32L46x devices). This parameter can be a value of @ref RCC_HSI48_Config */ RCC_PLLInitTypeDef PLL; /*!< Main PLL structure parameters */ }RCC_OscInitTypeDef; /** * @brief RCC System, AHB and APB busses clock configuration structure definition */ typedef struct { uint32_t ClockType; /*!< The clock to be configured. This parameter can be a value of @ref RCC_System_Clock_Type */ uint32_t SYSCLKSource; /*!< The clock source used as system clock (SYSCLK). This parameter can be a value of @ref RCC_System_Clock_Source */ uint32_t AHBCLKDivider; /*!< The AHB clock (HCLK) divider. This clock is derived from the system clock (SYSCLK). This parameter can be a value of @ref RCC_AHB_Clock_Source */ uint32_t APB1CLKDivider; /*!< The APB1 clock (PCLK1) divider. This clock is derived from the AHB clock (HCLK). This parameter can be a value of @ref RCC_APB1_APB2_Clock_Source */ uint32_t APB2CLKDivider; /*!< The APB2 clock (PCLK2) divider. This clock is derived from the AHB clock (HCLK). This parameter can be a value of @ref RCC_APB1_APB2_Clock_Source */ }RCC_ClkInitTypeDef; /** * @} */ /* Exported constants --------------------------------------------------------*/ /** @defgroup RCC_Exported_Constants RCC Exported Constants * @{ */ /** @defgroup RCC_Timeout_Value Timeout Values * @{ */ #define RCC_DBP_TIMEOUT_VALUE ((uint32_t)2U) /* 2 ms (minimum Tick + 1) */ #define RCC_LSE_TIMEOUT_VALUE LSE_STARTUP_TIMEOUT /** * @} */ /** @defgroup RCC_Oscillator_Type Oscillator Type * @{ */ #define RCC_OSCILLATORTYPE_NONE ((uint32_t)0x00000000U) /*!< Oscillator configuration unchanged */ #define RCC_OSCILLATORTYPE_HSE ((uint32_t)0x00000001U) /*!< HSE to configure */ #define RCC_OSCILLATORTYPE_HSI ((uint32_t)0x00000002U) /*!< HSI to configure */ #define RCC_OSCILLATORTYPE_LSE ((uint32_t)0x00000004U) /*!< LSE to configure */ #define RCC_OSCILLATORTYPE_LSI ((uint32_t)0x00000008U) /*!< LSI to configure */ #define RCC_OSCILLATORTYPE_MSI ((uint32_t)0x00000010U) /*!< MSI to configure */ #if defined(RCC_HSI48_SUPPORT) #define RCC_OSCILLATORTYPE_HSI48 ((uint32_t)0x00000020U) /*!< HSI48 to configure */ #endif /* RCC_HSI48_SUPPORT */ /** * @} */ /** @defgroup RCC_HSE_Config HSE Config * @{ */ #define RCC_HSE_OFF ((uint32_t)0x00000000U) /*!< HSE clock deactivation */ #define RCC_HSE_ON RCC_CR_HSEON /*!< HSE clock activation */ #define RCC_HSE_BYPASS ((uint32_t)(RCC_CR_HSEBYP | RCC_CR_HSEON)) /*!< External clock source for HSE clock */ /** * @} */ /** @defgroup RCC_LSE_Config LSE Config * @{ */ #define RCC_LSE_OFF ((uint32_t)0x00000000U) /*!< LSE clock deactivation */ #define RCC_LSE_ON RCC_BDCR_LSEON /*!< LSE clock activation */ #define RCC_LSE_BYPASS ((uint32_t)(RCC_BDCR_LSEBYP | RCC_BDCR_LSEON)) /*!< External clock source for LSE clock */ /** * @} */ /** @defgroup RCC_HSI_Config HSI Config * @{ */ #define RCC_HSI_OFF ((uint32_t)0x00000000U) /*!< HSI clock deactivation */ #define RCC_HSI_ON RCC_CR_HSION /*!< HSI clock activation */ #if defined(STM32L431xx) || defined(STM32L432xx) || defined(STM32L433xx) || defined(STM32L442xx) || defined(STM32L443xx) || \ defined(STM32L471xx) || defined(STM32L475xx) || defined(STM32L476xx) || defined(STM32L485xx) || defined(STM32L486xx) #define RCC_HSICALIBRATION_DEFAULT ((uint32_t)0x10U) /* Default HSI calibration trimming value */ #else #define RCC_HSICALIBRATION_DEFAULT ((uint32_t)0x40U) /* Default HSI calibration trimming value */ #endif /* STM32L431xx || STM32L432xx || STM32L433xx || STM32L442xx || STM32L443xx || */ /* STM32L471xx || STM32L475xx || STM32L476xx || STM32L485xx || STM32L486xx */ /** * @} */ /** @defgroup RCC_LSI_Config LSI Config * @{ */ #define RCC_LSI_OFF ((uint32_t)0x00000000U) /*!< LSI clock deactivation */ #define RCC_LSI_ON RCC_CSR_LSION /*!< LSI clock activation */ /** * @} */ /** @defgroup RCC_MSI_Config MSI Config * @{ */ #define RCC_MSI_OFF ((uint32_t)0x00000000U) /*!< MSI clock deactivation */ #define RCC_MSI_ON RCC_CR_MSION /*!< MSI clock activation */ #define RCC_MSICALIBRATION_DEFAULT ((uint32_t)0) /*!< Default MSI calibration trimming value */ /** * @} */ #if defined(RCC_HSI48_SUPPORT) /** @defgroup RCC_HSI48_Config HSI48 Config * @{ */ #define RCC_HSI48_OFF ((uint32_t)0x00000000U) /*!< HSI48 clock deactivation */ #define RCC_HSI48_ON RCC_CRRCR_HSI48ON /*!< HSI48 clock activation */ /** * @} */ #else /** @defgroup RCC_HSI48_Config HSI48 Config * @{ */ #define RCC_HSI48_OFF ((uint32_t)0x00000000U) /*!< HSI48 clock deactivation */ /** * @} */ #endif /* RCC_HSI48_SUPPORT */ /** @defgroup RCC_PLL_Config PLL Config * @{ */ #define RCC_PLL_NONE ((uint32_t)0x00000000U) /*!< PLL configuration unchanged */ #define RCC_PLL_OFF ((uint32_t)0x00000001U) /*!< PLL deactivation */ #define RCC_PLL_ON ((uint32_t)0x00000002U) /*!< PLL activation */ /** * @} */ /** @defgroup RCC_PLLP_Clock_Divider PLLP Clock Divider * @{ */ #if defined(RCC_PLLP_DIV_2_31_SUPPORT) #define RCC_PLLP_DIV2 ((uint32_t)0x00000002U) /*!< PLLP division factor = 2 */ #define RCC_PLLP_DIV3 ((uint32_t)0x00000003U) /*!< PLLP division factor = 3 */ #define RCC_PLLP_DIV4 ((uint32_t)0x00000004U) /*!< PLLP division factor = 4 */ #define RCC_PLLP_DIV5 ((uint32_t)0x00000005U) /*!< PLLP division factor = 5 */ #define RCC_PLLP_DIV6 ((uint32_t)0x00000006U) /*!< PLLP division factor = 6 */ #define RCC_PLLP_DIV7 ((uint32_t)0x00000007U) /*!< PLLP division factor = 7 */ #define RCC_PLLP_DIV8 ((uint32_t)0x00000008U) /*!< PLLP division factor = 8 */ #define RCC_PLLP_DIV9 ((uint32_t)0x00000009U) /*!< PLLP division factor = 9 */ #define RCC_PLLP_DIV10 ((uint32_t)0x0000000AU) /*!< PLLP division factor = 10 */ #define RCC_PLLP_DIV11 ((uint32_t)0x0000000BU) /*!< PLLP division factor = 11 */ #define RCC_PLLP_DIV12 ((uint32_t)0x0000000CU) /*!< PLLP division factor = 12 */ #define RCC_PLLP_DIV13 ((uint32_t)0x0000000DU) /*!< PLLP division factor = 13 */ #define RCC_PLLP_DIV14 ((uint32_t)0x0000000EU) /*!< PLLP division factor = 14 */ #define RCC_PLLP_DIV15 ((uint32_t)0x0000000FU) /*!< PLLP division factor = 15 */ #define RCC_PLLP_DIV16 ((uint32_t)0x00000010U) /*!< PLLP division factor = 16 */ #define RCC_PLLP_DIV17 ((uint32_t)0x00000011U) /*!< PLLP division factor = 17 */ #define RCC_PLLP_DIV18 ((uint32_t)0x00000012U) /*!< PLLP division factor = 18 */ #define RCC_PLLP_DIV19 ((uint32_t)0x00000013U) /*!< PLLP division factor = 19 */ #define RCC_PLLP_DIV20 ((uint32_t)0x00000014U) /*!< PLLP division factor = 20 */ #define RCC_PLLP_DIV21 ((uint32_t)0x00000015U) /*!< PLLP division factor = 21 */ #define RCC_PLLP_DIV22 ((uint32_t)0x00000016U) /*!< PLLP division factor = 22 */ #define RCC_PLLP_DIV23 ((uint32_t)0x00000017U) /*!< PLLP division factor = 23 */ #define RCC_PLLP_DIV24 ((uint32_t)0x00000018U) /*!< PLLP division factor = 24 */ #define RCC_PLLP_DIV25 ((uint32_t)0x00000019U) /*!< PLLP division factor = 25 */ #define RCC_PLLP_DIV26 ((uint32_t)0x0000001AU) /*!< PLLP division factor = 26 */ #define RCC_PLLP_DIV27 ((uint32_t)0x0000001BU) /*!< PLLP division factor = 27 */ #define RCC_PLLP_DIV28 ((uint32_t)0x0000001CU) /*!< PLLP division factor = 28 */ #define RCC_PLLP_DIV29 ((uint32_t)0x0000001DU) /*!< PLLP division factor = 29 */ #define RCC_PLLP_DIV30 ((uint32_t)0x0000001EU) /*!< PLLP division factor = 30 */ #define RCC_PLLP_DIV31 ((uint32_t)0x0000001FU) /*!< PLLP division factor = 31 */ #else #define RCC_PLLP_DIV7 ((uint32_t)0x00000007U) /*!< PLLP division factor = 7 */ #define RCC_PLLP_DIV17 ((uint32_t)0x00000011U) /*!< PLLP division factor = 17 */ #endif /* RCC_PLLP_DIV_2_31_SUPPORT */ /** * @} */ /** @defgroup RCC_PLLQ_Clock_Divider PLLQ Clock Divider * @{ */ #define RCC_PLLQ_DIV2 ((uint32_t)0x00000002U) /*!< PLLQ division factor = 2 */ #define RCC_PLLQ_DIV4 ((uint32_t)0x00000004U) /*!< PLLQ division factor = 4 */ #define RCC_PLLQ_DIV6 ((uint32_t)0x00000006U) /*!< PLLQ division factor = 6 */ #define RCC_PLLQ_DIV8 ((uint32_t)0x00000008U) /*!< PLLQ division factor = 8 */ /** * @} */ /** @defgroup RCC_PLLR_Clock_Divider PLLR Clock Divider * @{ */ #define RCC_PLLR_DIV2 ((uint32_t)0x00000002U) /*!< PLLR division factor = 2 */ #define RCC_PLLR_DIV4 ((uint32_t)0x00000004U) /*!< PLLR division factor = 4 */ #define RCC_PLLR_DIV6 ((uint32_t)0x00000006U) /*!< PLLR division factor = 6 */ #define RCC_PLLR_DIV8 ((uint32_t)0x00000008U) /*!< PLLR division factor = 8 */ /** * @} */ /** @defgroup RCC_PLL_Clock_Source PLL Clock Source * @{ */ #define RCC_PLLSOURCE_NONE ((uint32_t)0x00000000U) /*!< No clock selected as PLL entry clock source */ #define RCC_PLLSOURCE_MSI RCC_PLLCFGR_PLLSRC_MSI /*!< MSI clock selected as PLL entry clock source */ #define RCC_PLLSOURCE_HSI RCC_PLLCFGR_PLLSRC_HSI /*!< HSI clock selected as PLL entry clock source */ #define RCC_PLLSOURCE_HSE RCC_PLLCFGR_PLLSRC_HSE /*!< HSE clock selected as PLL entry clock source */ /** * @} */ /** @defgroup RCC_PLL_Clock_Output PLL Clock Output * @{ */ #if defined(RCC_PLLSAI2_SUPPORT) #define RCC_PLL_SAI3CLK RCC_PLLCFGR_PLLPEN /*!< PLLSAI3CLK selection from main PLL (for devices with PLLSAI2) */ #else #define RCC_PLL_SAI2CLK RCC_PLLCFGR_PLLPEN /*!< PLLSAI2CLK selection from main PLL (for devices without PLLSAI2) */ #endif /* RCC_PLLSAI2_SUPPORT */ #define RCC_PLL_48M1CLK RCC_PLLCFGR_PLLQEN /*!< PLL48M1CLK selection from main PLL */ #define RCC_PLL_SYSCLK RCC_PLLCFGR_PLLREN /*!< PLLCLK selection from main PLL */ /** * @} */ /** @defgroup RCC_PLLSAI1_Clock_Output PLLSAI1 Clock Output * @{ */ #define RCC_PLLSAI1_SAI1CLK RCC_PLLSAI1CFGR_PLLSAI1PEN /*!< PLLSAI1CLK selection from PLLSAI1 */ #define RCC_PLLSAI1_48M2CLK RCC_PLLSAI1CFGR_PLLSAI1QEN /*!< PLL48M2CLK selection from PLLSAI1 */ #define RCC_PLLSAI1_ADC1CLK RCC_PLLSAI1CFGR_PLLSAI1REN /*!< PLLADC1CLK selection from PLLSAI1 */ /** * @} */ #if defined(RCC_PLLSAI2_SUPPORT) /** @defgroup RCC_PLLSAI2_Clock_Output PLLSAI2 Clock Output * @{ */ #define RCC_PLLSAI2_SAI2CLK RCC_PLLSAI2CFGR_PLLSAI2PEN /*!< PLLSAI2CLK selection from PLLSAI2 */ #define RCC_PLLSAI2_ADC2CLK RCC_PLLSAI2CFGR_PLLSAI2REN /*!< PLLADC2CLK selection from PLLSAI2 */ /** * @} */ #endif /* RCC_PLLSAI2_SUPPORT */ /** @defgroup RCC_MSI_Clock_Range MSI Clock Range * @{ */ #define RCC_MSIRANGE_0 RCC_CR_MSIRANGE_0 /*!< MSI = 100 KHz */ #define RCC_MSIRANGE_1 RCC_CR_MSIRANGE_1 /*!< MSI = 200 KHz */ #define RCC_MSIRANGE_2 RCC_CR_MSIRANGE_2 /*!< MSI = 400 KHz */ #define RCC_MSIRANGE_3 RCC_CR_MSIRANGE_3 /*!< MSI = 800 KHz */ #define RCC_MSIRANGE_4 RCC_CR_MSIRANGE_4 /*!< MSI = 1 MHz */ #define RCC_MSIRANGE_5 RCC_CR_MSIRANGE_5 /*!< MSI = 2 MHz */ #define RCC_MSIRANGE_6 RCC_CR_MSIRANGE_6 /*!< MSI = 4 MHz */ #define RCC_MSIRANGE_7 RCC_CR_MSIRANGE_7 /*!< MSI = 8 MHz */ #define RCC_MSIRANGE_8 RCC_CR_MSIRANGE_8 /*!< MSI = 16 MHz */ #define RCC_MSIRANGE_9 RCC_CR_MSIRANGE_9 /*!< MSI = 24 MHz */ #define RCC_MSIRANGE_10 RCC_CR_MSIRANGE_10 /*!< MSI = 32 MHz */ #define RCC_MSIRANGE_11 RCC_CR_MSIRANGE_11 /*!< MSI = 48 MHz */ /** * @} */ /** @defgroup RCC_System_Clock_Type System Clock Type * @{ */ #define RCC_CLOCKTYPE_SYSCLK ((uint32_t)0x00000001U) /*!< SYSCLK to configure */ #define RCC_CLOCKTYPE_HCLK ((uint32_t)0x00000002U) /*!< HCLK to configure */ #define RCC_CLOCKTYPE_PCLK1 ((uint32_t)0x00000004U) /*!< PCLK1 to configure */ #define RCC_CLOCKTYPE_PCLK2 ((uint32_t)0x00000008U) /*!< PCLK2 to configure */ /** * @} */ /** @defgroup RCC_System_Clock_Source System Clock Source * @{ */ #define RCC_SYSCLKSOURCE_MSI RCC_CFGR_SW_MSI /*!< MSI selection as system clock */ #define RCC_SYSCLKSOURCE_HSI RCC_CFGR_SW_HSI /*!< HSI selection as system clock */ #define RCC_SYSCLKSOURCE_HSE RCC_CFGR_SW_HSE /*!< HSE selection as system clock */ #define RCC_SYSCLKSOURCE_PLLCLK RCC_CFGR_SW_PLL /*!< PLL selection as system clock */ /** * @} */ /** @defgroup RCC_System_Clock_Source_Status System Clock Source Status * @{ */ #define RCC_SYSCLKSOURCE_STATUS_MSI RCC_CFGR_SWS_MSI /*!< MSI used as system clock */ #define RCC_SYSCLKSOURCE_STATUS_HSI RCC_CFGR_SWS_HSI /*!< HSI used as system clock */ #define RCC_SYSCLKSOURCE_STATUS_HSE RCC_CFGR_SWS_HSE /*!< HSE used as system clock */ #define RCC_SYSCLKSOURCE_STATUS_PLLCLK RCC_CFGR_SWS_PLL /*!< PLL used as system clock */ /** * @} */ /** @defgroup RCC_AHB_Clock_Source AHB Clock Source * @{ */ #define RCC_SYSCLK_DIV1 RCC_CFGR_HPRE_DIV1 /*!< SYSCLK not divided */ #define RCC_SYSCLK_DIV2 RCC_CFGR_HPRE_DIV2 /*!< SYSCLK divided by 2 */ #define RCC_SYSCLK_DIV4 RCC_CFGR_HPRE_DIV4 /*!< SYSCLK divided by 4 */ #define RCC_SYSCLK_DIV8 RCC_CFGR_HPRE_DIV8 /*!< SYSCLK divided by 8 */ #define RCC_SYSCLK_DIV16 RCC_CFGR_HPRE_DIV16 /*!< SYSCLK divided by 16 */ #define RCC_SYSCLK_DIV64 RCC_CFGR_HPRE_DIV64 /*!< SYSCLK divided by 64 */ #define RCC_SYSCLK_DIV128 RCC_CFGR_HPRE_DIV128 /*!< SYSCLK divided by 128 */ #define RCC_SYSCLK_DIV256 RCC_CFGR_HPRE_DIV256 /*!< SYSCLK divided by 256 */ #define RCC_SYSCLK_DIV512 RCC_CFGR_HPRE_DIV512 /*!< SYSCLK divided by 512 */ /** * @} */ /** @defgroup RCC_APB1_APB2_Clock_Source APB1 APB2 Clock Source * @{ */ #define RCC_HCLK_DIV1 RCC_CFGR_PPRE1_DIV1 /*!< HCLK not divided */ #define RCC_HCLK_DIV2 RCC_CFGR_PPRE1_DIV2 /*!< HCLK divided by 2 */ #define RCC_HCLK_DIV4 RCC_CFGR_PPRE1_DIV4 /*!< HCLK divided by 4 */ #define RCC_HCLK_DIV8 RCC_CFGR_PPRE1_DIV8 /*!< HCLK divided by 8 */ #define RCC_HCLK_DIV16 RCC_CFGR_PPRE1_DIV16 /*!< HCLK divided by 16 */ /** * @} */ /** @defgroup RCC_RTC_Clock_Source RTC Clock Source * @{ */ #define RCC_RTCCLKSOURCE_NO_CLK ((uint32_t)0x00000000U) /*!< No clock used as RTC clock */ #define RCC_RTCCLKSOURCE_LSE RCC_BDCR_RTCSEL_0 /*!< LSE oscillator clock used as RTC clock */ #define RCC_RTCCLKSOURCE_LSI RCC_BDCR_RTCSEL_1 /*!< LSI oscillator clock used as RTC clock */ #define RCC_RTCCLKSOURCE_HSE_DIV32 RCC_BDCR_RTCSEL /*!< HSE oscillator clock divided by 32 used as RTC clock */ /** * @} */ /** @defgroup RCC_MCO_Index MCO Index * @{ */ #define RCC_MCO1 ((uint32_t)0x00000000U) #define RCC_MCO RCC_MCO1 /*!< MCO1 to be compliant with other families with 2 MCOs*/ /** * @} */ /** @defgroup RCC_MCO1_Clock_Source MCO1 Clock Source * @{ */ #define RCC_MCO1SOURCE_NOCLOCK ((uint32_t)0x00000000U) /*!< MCO1 output disabled, no clock on MCO1 */ #define RCC_MCO1SOURCE_SYSCLK RCC_CFGR_MCOSEL_0 /*!< SYSCLK selection as MCO1 source */ #define RCC_MCO1SOURCE_MSI RCC_CFGR_MCOSEL_1 /*!< MSI selection as MCO1 source */ #define RCC_MCO1SOURCE_HSI (RCC_CFGR_MCOSEL_0| RCC_CFGR_MCOSEL_1) /*!< HSI selection as MCO1 source */ #define RCC_MCO1SOURCE_HSE RCC_CFGR_MCOSEL_2 /*!< HSE selection as MCO1 source */ #define RCC_MCO1SOURCE_PLLCLK (RCC_CFGR_MCOSEL_0|RCC_CFGR_MCOSEL_2) /*!< PLLCLK selection as MCO1 source */ #define RCC_MCO1SOURCE_LSI (RCC_CFGR_MCOSEL_1|RCC_CFGR_MCOSEL_2) /*!< LSI selection as MCO1 source */ #define RCC_MCO1SOURCE_LSE (RCC_CFGR_MCOSEL_0|RCC_CFGR_MCOSEL_1|RCC_CFGR_MCOSEL_2) /*!< LSE selection as MCO1 source */ #if defined(RCC_HSI48_SUPPORT) #define RCC_MCO1SOURCE_HSI48 RCC_CFGR_MCOSEL_3 /*!< HSI48 selection as MCO1 source (STM32L43x/STM32L44x devices) */ #endif /* RCC_HSI48_SUPPORT */ /** * @} */ /** @defgroup RCC_MCOx_Clock_Prescaler MCO1 Clock Prescaler * @{ */ #define RCC_MCODIV_1 RCC_CFGR_MCOPRE_DIV1 /*!< MCO not divided */ #define RCC_MCODIV_2 RCC_CFGR_MCOPRE_DIV2 /*!< MCO divided by 2 */ #define RCC_MCODIV_4 RCC_CFGR_MCOPRE_DIV4 /*!< MCO divided by 4 */ #define RCC_MCODIV_8 RCC_CFGR_MCOPRE_DIV8 /*!< MCO divided by 8 */ #define RCC_MCODIV_16 RCC_CFGR_MCOPRE_DIV16 /*!< MCO divided by 16 */ /** * @} */ /** @defgroup RCC_Interrupt Interrupts * @{ */ #define RCC_IT_LSIRDY RCC_CIFR_LSIRDYF /*!< LSI Ready Interrupt flag */ #define RCC_IT_LSERDY RCC_CIFR_LSERDYF /*!< LSE Ready Interrupt flag */ #define RCC_IT_MSIRDY RCC_CIFR_MSIRDYF /*!< MSI Ready Interrupt flag */ #define RCC_IT_HSIRDY RCC_CIFR_HSIRDYF /*!< HSI16 Ready Interrupt flag */ #define RCC_IT_HSERDY RCC_CIFR_HSERDYF /*!< HSE Ready Interrupt flag */ #define RCC_IT_PLLRDY RCC_CIFR_PLLRDYF /*!< PLL Ready Interrupt flag */ #define RCC_IT_PLLSAI1RDY RCC_CIFR_PLLSAI1RDYF /*!< PLLSAI1 Ready Interrupt flag */ #if defined(RCC_PLLSAI2_SUPPORT) #define RCC_IT_PLLSAI2RDY RCC_CIFR_PLLSAI2RDYF /*!< PLLSAI2 Ready Interrupt flag */ #endif /* RCC_PLLSAI2_SUPPORT */ #define RCC_IT_CSS RCC_CIFR_CSSF /*!< Clock Security System Interrupt flag */ #define RCC_IT_LSECSS RCC_CIFR_LSECSSF /*!< LSE Clock Security System Interrupt flag */ #if defined(RCC_HSI48_SUPPORT) #define RCC_IT_HSI48RDY RCC_CIFR_HSI48RDYF /*!< HSI48 Ready Interrupt flag */ #endif /* RCC_HSI48_SUPPORT */ /** * @} */ /** @defgroup RCC_Flag Flags * Elements values convention: XXXYYYYYb * - YYYYY : Flag position in the register * - XXX : Register index * - 001: CR register * - 010: BDCR register * - 011: CSR register * - 100: CRRCR register * @{ */ /* Flags in the CR register */ #define RCC_FLAG_MSIRDY ((uint32_t)((CR_REG_INDEX << 5U) | POSITION_VAL(RCC_CR_MSIRDY))) /*!< MSI Ready flag */ #define RCC_FLAG_HSIRDY ((uint32_t)((CR_REG_INDEX << 5U) | POSITION_VAL(RCC_CR_HSIRDY))) /*!< HSI Ready flag */ #define RCC_FLAG_HSERDY ((uint32_t)((CR_REG_INDEX << 5U) | POSITION_VAL(RCC_CR_HSERDY))) /*!< HSE Ready flag */ #define RCC_FLAG_PLLRDY ((uint32_t)((CR_REG_INDEX << 5U) | POSITION_VAL(RCC_CR_PLLRDY))) /*!< PLL Ready flag */ #define RCC_FLAG_PLLSAI1RDY ((uint32_t)((CR_REG_INDEX << 5U) | POSITION_VAL(RCC_CR_PLLSAI1RDY))) /*!< PLLSAI1 Ready flag */ #if defined(RCC_PLLSAI2_SUPPORT) #define RCC_FLAG_PLLSAI2RDY ((uint32_t)((CR_REG_INDEX << 5U) | POSITION_VAL(RCC_CR_PLLSAI2RDY))) /*!< PLLSAI2 Ready flag */ #endif /* RCC_PLLSAI2_SUPPORT */ /* Flags in the BDCR register */ #define RCC_FLAG_LSERDY ((uint32_t)((BDCR_REG_INDEX << 5U) | POSITION_VAL(RCC_BDCR_LSERDY))) /*!< LSE Ready flag */ #define RCC_FLAG_LSECSSD ((uint32_t)((BDCR_REG_INDEX << 5U) | POSITION_VAL(RCC_BDCR_LSECSSD))) /*!< LSE Clock Security System Interrupt flag */ /* Flags in the CSR register */ #define RCC_FLAG_LSIRDY ((uint32_t)((CSR_REG_INDEX << 5U) | POSITION_VAL(RCC_CSR_LSIRDY))) /*!< LSI Ready flag */ #define RCC_FLAG_RMVF ((uint32_t)((CSR_REG_INDEX << 5U) | POSITION_VAL(RCC_CSR_RMVF))) /*!< Remove reset flag */ #define RCC_FLAG_FWRST ((uint32_t)((CSR_REG_INDEX << 5U) | POSITION_VAL(RCC_CSR_FWRSTF))) /*!< Firewall reset flag */ #define RCC_FLAG_OBLRST ((uint32_t)((CSR_REG_INDEX << 5U) | POSITION_VAL(RCC_CSR_OBLRSTF))) /*!< Option Byte Loader reset flag */ #define RCC_FLAG_PINRST ((uint32_t)((CSR_REG_INDEX << 5U) | POSITION_VAL(RCC_CSR_PINRSTF))) /*!< PIN reset flag */ #define RCC_FLAG_BORRST ((uint32_t)((CSR_REG_INDEX << 5U) | POSITION_VAL(RCC_CSR_BORRSTF))) /*!< BOR reset flag */ #define RCC_FLAG_SFTRST ((uint32_t)((CSR_REG_INDEX << 5U) | POSITION_VAL(RCC_CSR_SFTRSTF))) /*!< Software Reset flag */ #define RCC_FLAG_IWDGRST ((uint32_t)((CSR_REG_INDEX << 5U) | POSITION_VAL(RCC_CSR_IWDGRSTF))) /*!< Independent Watchdog reset flag */ #define RCC_FLAG_WWDGRST ((uint32_t)((CSR_REG_INDEX << 5U) | POSITION_VAL(RCC_CSR_WWDGRSTF))) /*!< Window watchdog reset flag */ #define RCC_FLAG_LPWRRST ((uint32_t)((CSR_REG_INDEX << 5U) | POSITION_VAL(RCC_CSR_LPWRRSTF))) /*!< Low-Power reset flag */ #if defined(RCC_HSI48_SUPPORT) /* Flags in the CRRCR register */ #define RCC_FLAG_HSI48RDY ((uint32_t)((CRRCR_REG_INDEX << 5U) | POSITION_VAL(RCC_CRRCR_HSI48RDY))) /*!< HSI48 Ready flag */ #endif /* RCC_HSI48_SUPPORT */ /** * @} */ /** @defgroup RCC_LSEDrive_Config LSE Drive Config * @{ */ #define RCC_LSEDRIVE_LOW ((uint32_t)0x00000000U) /*!< LSE low drive capability */ #define RCC_LSEDRIVE_MEDIUMLOW RCC_BDCR_LSEDRV_0 /*!< LSE medium low drive capability */ #define RCC_LSEDRIVE_MEDIUMHIGH RCC_BDCR_LSEDRV_1 /*!< LSE medium high drive capability */ #define RCC_LSEDRIVE_HIGH RCC_BDCR_LSEDRV /*!< LSE high drive capability */ /** * @} */ /** @defgroup RCC_Stop_WakeUpClock Wake-Up from STOP Clock * @{ */ #define RCC_STOP_WAKEUPCLOCK_MSI ((uint32_t)0x00000000U) /*!< MSI selection after wake-up from STOP */ #define RCC_STOP_WAKEUPCLOCK_HSI RCC_CFGR_STOPWUCK /*!< HSI selection after wake-up from STOP */ /** * @} */ /** * @} */ /* Exported macros -----------------------------------------------------------*/ /** @defgroup RCC_Exported_Macros RCC Exported Macros * @{ */ /** @defgroup RCC_AHB1_Peripheral_Clock_Enable_Disable AHB1 Peripheral Clock Enable Disable * @brief Enable or disable the AHB1 peripheral clock. * @note After reset, the peripheral clock (used for registers read/write access) * is disabled and the application software has to enable this clock before * using it. * @{ */ #define __HAL_RCC_DMA1_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA1EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA1EN); \ UNUSED(tmpreg); \ } while(0) #define __HAL_RCC_DMA2_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA2EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA2EN); \ UNUSED(tmpreg); \ } while(0) #define __HAL_RCC_FLASH_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_FLASHEN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_FLASHEN); \ UNUSED(tmpreg); \ } while(0) #define __HAL_RCC_CRC_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN); \ UNUSED(tmpreg); \ } while(0) #define __HAL_RCC_TSC_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_TSCEN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_TSCEN); \ UNUSED(tmpreg); \ } while(0) #define __HAL_RCC_DMA1_CLK_DISABLE() CLEAR_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA1EN) #define __HAL_RCC_DMA2_CLK_DISABLE() CLEAR_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA2EN) #define __HAL_RCC_FLASH_CLK_DISABLE() CLEAR_BIT(RCC->AHB1ENR, RCC_AHB1ENR_FLASHEN) #define __HAL_RCC_CRC_CLK_DISABLE() CLEAR_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN) #define __HAL_RCC_TSC_CLK_DISABLE() CLEAR_BIT(RCC->AHB1ENR, RCC_AHB1ENR_TSCEN) /** * @} */ /** @defgroup RCC_AHB2_Peripheral_Clock_Enable_Disable AHB2 Peripheral Clock Enable Disable * @brief Enable or disable the AHB2 peripheral clock. * @note After reset, the peripheral clock (used for registers read/write access) * is disabled and the application software has to enable this clock before * using it. * @{ */ #define __HAL_RCC_GPIOA_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOAEN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOAEN); \ UNUSED(tmpreg); \ } while(0) #define __HAL_RCC_GPIOB_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOBEN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOBEN); \ UNUSED(tmpreg); \ } while(0) #define __HAL_RCC_GPIOC_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOCEN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOCEN); \ UNUSED(tmpreg); \ } while(0) #if defined(GPIOD) #define __HAL_RCC_GPIOD_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIODEN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIODEN); \ UNUSED(tmpreg); \ } while(0) #endif /* GPIOD */ #if defined(GPIOE) #define __HAL_RCC_GPIOE_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOEEN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOEEN); \ UNUSED(tmpreg); \ } while(0) #endif /* GPIOE */ #if defined(GPIOF) #define __HAL_RCC_GPIOF_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOFEN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOFEN); \ UNUSED(tmpreg); \ } while(0) #endif /* GPIOF */ #if defined(GPIOG) #define __HAL_RCC_GPIOG_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOGEN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOGEN); \ UNUSED(tmpreg); \ } while(0) #endif /* GPIOG */ #define __HAL_RCC_GPIOH_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOHEN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOHEN); \ UNUSED(tmpreg); \ } while(0) #if defined(USB_OTG_FS) #define __HAL_RCC_USB_OTG_FS_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_OTGFSEN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_OTGFSEN); \ UNUSED(tmpreg); \ } while(0) #endif /* USB_OTG_FS */ #define __HAL_RCC_ADC_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_ADCEN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_ADCEN); \ UNUSED(tmpreg); \ } while(0) #if defined(AES) #define __HAL_RCC_AES_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_AESEN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_AESEN); \ UNUSED(tmpreg); \ } while(0) #endif /* AES */ #define __HAL_RCC_RNG_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN); \ UNUSED(tmpreg); \ } while(0) #define __HAL_RCC_GPIOA_CLK_DISABLE() CLEAR_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOAEN) #define __HAL_RCC_GPIOB_CLK_DISABLE() CLEAR_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOBEN) #define __HAL_RCC_GPIOC_CLK_DISABLE() CLEAR_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOCEN) #if defined(GPIOD) #define __HAL_RCC_GPIOD_CLK_DISABLE() CLEAR_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIODEN) #endif /* GPIOD */ #if defined(GPIOE) #define __HAL_RCC_GPIOE_CLK_DISABLE() CLEAR_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOEEN) #endif /* GPIOE */ #if defined(GPIOF) #define __HAL_RCC_GPIOF_CLK_DISABLE() CLEAR_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOFEN) #endif /* GPIOF */ #if defined(GPIOG) #define __HAL_RCC_GPIOG_CLK_DISABLE() CLEAR_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOGEN) #endif /* GPIOG */ #define __HAL_RCC_GPIOH_CLK_DISABLE() CLEAR_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOHEN) #if defined(USB_OTG_FS) #define __HAL_RCC_USB_OTG_FS_CLK_DISABLE() CLEAR_BIT(RCC->AHB2ENR, RCC_AHB2ENR_OTGFSEN); #endif /* USB_OTG_FS */ #define __HAL_RCC_ADC_CLK_DISABLE() CLEAR_BIT(RCC->AHB2ENR, RCC_AHB2ENR_ADCEN) #if defined(AES) #define __HAL_RCC_AES_CLK_DISABLE() CLEAR_BIT(RCC->AHB2ENR, RCC_AHB2ENR_AESEN); #endif /* AES */ #define __HAL_RCC_RNG_CLK_DISABLE() CLEAR_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN) /** * @} */ /** @defgroup RCC_AHB3_Clock_Enable_Disable AHB3 Peripheral Clock Enable Disable * @brief Enable or disable the AHB3 peripheral clock. * @note After reset, the peripheral clock (used for registers read/write access) * is disabled and the application software has to enable this clock before * using it. * @{ */ #if defined(FMC_BANK1) #define __HAL_RCC_FMC_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN); \ UNUSED(tmpreg); \ } while(0) #endif /* FMC_BANK1 */ #if defined(QUADSPI) #define __HAL_RCC_QSPI_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->AHB3ENR, RCC_AHB3ENR_QSPIEN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_QSPIEN); \ UNUSED(tmpreg); \ } while(0) #endif /* QUADSPI */ #if defined(FMC_BANK1) #define __HAL_RCC_FMC_CLK_DISABLE() CLEAR_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN) #endif /* FMC_BANK1 */ #if defined(QUADSPI) #define __HAL_RCC_QSPI_CLK_DISABLE() CLEAR_BIT(RCC->AHB3ENR, RCC_AHB3ENR_QSPIEN) #endif /* QUADSPI */ /** * @} */ /** @defgroup RCC_APB1_Clock_Enable_Disable APB1 Peripheral Clock Enable Disable * @brief Enable or disable the APB1 peripheral clock. * @note After reset, the peripheral clock (used for registers read/write access) * is disabled and the application software has to enable this clock before * using it. * @{ */ #define __HAL_RCC_TIM2_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM2EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM2EN); \ UNUSED(tmpreg); \ } while(0) #if defined(TIM3) #define __HAL_RCC_TIM3_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM3EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM3EN); \ UNUSED(tmpreg); \ } while(0) #endif /* TIM3 */ #if defined(TIM4) #define __HAL_RCC_TIM4_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM4EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM4EN); \ UNUSED(tmpreg); \ } while(0) #endif /* TIM4 */ #if defined(TIM5) #define __HAL_RCC_TIM5_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM5EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM5EN); \ UNUSED(tmpreg); \ } while(0) #endif /* TIM5 */ #define __HAL_RCC_TIM6_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM6EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM6EN); \ UNUSED(tmpreg); \ } while(0) #define __HAL_RCC_TIM7_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM7EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM7EN); \ UNUSED(tmpreg); \ } while(0) #if defined(LCD) #define __HAL_RCC_LCD_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_LCDEN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_LCDEN); \ UNUSED(tmpreg); \ } while(0) #endif /* LCD */ #if defined(RCC_APB1ENR1_RTCAPBEN) #define __HAL_RCC_RTCAPB_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_RTCAPBEN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_RTCAPBEN); \ UNUSED(tmpreg); \ } while(0) #endif /* RCC_APB1ENR1_RTCAPBEN */ #define __HAL_RCC_WWDG_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_WWDGEN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_WWDGEN); \ UNUSED(tmpreg); \ } while(0) #if defined(SPI2) #define __HAL_RCC_SPI2_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_SPI2EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_SPI2EN); \ UNUSED(tmpreg); \ } while(0) #endif /* SPI2 */ #define __HAL_RCC_SPI3_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_SPI3EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_SPI3EN); \ UNUSED(tmpreg); \ } while(0) #define __HAL_RCC_USART2_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_USART2EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_USART2EN); \ UNUSED(tmpreg); \ } while(0) #if defined(USART3) #define __HAL_RCC_USART3_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_USART3EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_USART3EN); \ UNUSED(tmpreg); \ } while(0) #endif /* USART3 */ #if defined(UART4) #define __HAL_RCC_UART4_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_UART4EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_UART4EN); \ UNUSED(tmpreg); \ } while(0) #endif /* UART4 */ #if defined(UART5) #define __HAL_RCC_UART5_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_UART5EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_UART5EN); \ UNUSED(tmpreg); \ } while(0) #endif /* UART5 */ #define __HAL_RCC_I2C1_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C1EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C1EN); \ UNUSED(tmpreg); \ } while(0) #if defined(I2C2) #define __HAL_RCC_I2C2_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C2EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C2EN); \ UNUSED(tmpreg); \ } while(0) #endif /* I2C2 */ #define __HAL_RCC_I2C3_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C3EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C3EN); \ UNUSED(tmpreg); \ } while(0) #if defined(I2C4) #define __HAL_RCC_I2C4_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR2, RCC_APB1ENR2_I2C4EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR2, RCC_APB1ENR2_I2C4EN); \ UNUSED(tmpreg); \ } while(0) #endif /* I2C4 */ #if defined(CRS) #define __HAL_RCC_CRS_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_CRSEN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_CRSEN); \ UNUSED(tmpreg); \ } while(0) #endif /* CRS */ #define __HAL_RCC_CAN1_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_CAN1EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_CAN1EN); \ UNUSED(tmpreg); \ } while(0) #if defined(USB) #define __HAL_RCC_USB_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_USBFSEN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_USBFSEN); \ UNUSED(tmpreg); \ } while(0) #endif /* USB */ #define __HAL_RCC_PWR_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_PWREN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_PWREN); \ UNUSED(tmpreg); \ } while(0) #define __HAL_RCC_DAC1_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_DAC1EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_DAC1EN); \ UNUSED(tmpreg); \ } while(0) #define __HAL_RCC_OPAMP_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_OPAMPEN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_OPAMPEN); \ UNUSED(tmpreg); \ } while(0) #define __HAL_RCC_LPTIM1_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_LPTIM1EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_LPTIM1EN); \ UNUSED(tmpreg); \ } while(0) #define __HAL_RCC_LPUART1_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR2, RCC_APB1ENR2_LPUART1EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR2, RCC_APB1ENR2_LPUART1EN); \ UNUSED(tmpreg); \ } while(0) #if defined(SWPMI1) #define __HAL_RCC_SWPMI1_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR2, RCC_APB1ENR2_SWPMI1EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR2, RCC_APB1ENR2_SWPMI1EN); \ UNUSED(tmpreg); \ } while(0) #endif /* SWPMI1 */ #define __HAL_RCC_LPTIM2_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB1ENR2, RCC_APB1ENR2_LPTIM2EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR2, RCC_APB1ENR2_LPTIM2EN); \ UNUSED(tmpreg); \ } while(0) #define __HAL_RCC_TIM2_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM2EN) #if defined(TIM3) #define __HAL_RCC_TIM3_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM3EN) #endif /* TIM3 */ #if defined(TIM4) #define __HAL_RCC_TIM4_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM4EN) #endif /* TIM4 */ #if defined(TIM5) #define __HAL_RCC_TIM5_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM5EN) #endif /* TIM5 */ #define __HAL_RCC_TIM6_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM6EN) #define __HAL_RCC_TIM7_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM7EN) #if defined(LCD) #define __HAL_RCC_LCD_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_LCDEN); #endif /* LCD */ #if defined(RCC_APB1ENR1_RTCAPBEN) #define __HAL_RCC_RTCAPB_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_RTCAPBEN); #endif /* RCC_APB1ENR1_RTCAPBEN */ #if defined(SPI2) #define __HAL_RCC_SPI2_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_SPI2EN) #endif /* SPI2 */ #define __HAL_RCC_SPI3_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_SPI3EN) #define __HAL_RCC_USART2_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_USART2EN) #if defined(USART3) #define __HAL_RCC_USART3_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_USART3EN) #endif /* USART3 */ #if defined(UART4) #define __HAL_RCC_UART4_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_UART4EN) #endif /* UART4 */ #if defined(UART5) #define __HAL_RCC_UART5_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_UART5EN) #endif /* UART5 */ #define __HAL_RCC_I2C1_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C1EN) #if defined(I2C2) #define __HAL_RCC_I2C2_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C2EN) #endif /* I2C2 */ #define __HAL_RCC_I2C3_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C3EN) #if defined(I2C4) #define __HAL_RCC_I2C4_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR2, RCC_APB1ENR2_I2C4EN) #endif /* I2C4 */ #if defined(CRS) #define __HAL_RCC_CRS_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_CRSEN); #endif /* CRS */ #define __HAL_RCC_CAN1_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_CAN1EN) #if defined(USB) #define __HAL_RCC_USB_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_USBFSEN); #endif /* USB */ #define __HAL_RCC_PWR_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_PWREN) #define __HAL_RCC_DAC1_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_DAC1EN) #define __HAL_RCC_OPAMP_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_OPAMPEN) #define __HAL_RCC_LPTIM1_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_LPTIM1EN) #define __HAL_RCC_LPUART1_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR2, RCC_APB1ENR2_LPUART1EN) #if defined(SWPMI1) #define __HAL_RCC_SWPMI1_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR2, RCC_APB1ENR2_SWPMI1EN) #endif /* SWPMI1 */ #define __HAL_RCC_LPTIM2_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR2, RCC_APB1ENR2_LPTIM2EN) /** * @} */ /** @defgroup RCC_APB2_Clock_Enable_Disable APB2 Peripheral Clock Enable Disable * @brief Enable or disable the APB2 peripheral clock. * @note After reset, the peripheral clock (used for registers read/write access) * is disabled and the application software has to enable this clock before * using it. * @{ */ #define __HAL_RCC_SYSCFG_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SYSCFGEN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SYSCFGEN); \ UNUSED(tmpreg); \ } while(0) #define __HAL_RCC_FIREWALL_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_FWEN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_FWEN); \ UNUSED(tmpreg); \ } while(0) #if defined(SDMMC1) #define __HAL_RCC_SDMMC1_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SDMMC1EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SDMMC1EN); \ UNUSED(tmpreg); \ } while(0) #endif /* SDMMC1 */ #define __HAL_RCC_TIM1_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM1EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM1EN); \ UNUSED(tmpreg); \ } while(0) #define __HAL_RCC_SPI1_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI1EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI1EN); \ UNUSED(tmpreg); \ } while(0) #if defined(TIM8) #define __HAL_RCC_TIM8_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM8EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM8EN); \ UNUSED(tmpreg); \ } while(0) #endif /* TIM8 */ #define __HAL_RCC_USART1_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_USART1EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_USART1EN); \ UNUSED(tmpreg); \ } while(0) #define __HAL_RCC_TIM15_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM15EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM15EN); \ UNUSED(tmpreg); \ } while(0) #define __HAL_RCC_TIM16_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM16EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM16EN); \ UNUSED(tmpreg); \ } while(0) #if defined(TIM17) #define __HAL_RCC_TIM17_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM17EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM17EN); \ UNUSED(tmpreg); \ } while(0) #endif /* TIM17 */ #define __HAL_RCC_SAI1_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI1EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI1EN); \ UNUSED(tmpreg); \ } while(0) #if defined(SAI2) #define __HAL_RCC_SAI2_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI2EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI2EN); \ UNUSED(tmpreg); \ } while(0) #endif /* SAI2 */ #if defined(DFSDM1_Filter0) #define __HAL_RCC_DFSDM1_CLK_ENABLE() do { \ __IO uint32_t tmpreg; \ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_DFSDM1EN); \ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_DFSDM1EN); \ UNUSED(tmpreg); \ } while(0) #endif /* DFSDM1_Filter0 */ #define __HAL_RCC_SYSCFG_CLK_DISABLE() CLEAR_BIT(RCC->APB2ENR, RCC_APB2ENR_SYSCFGEN) #if defined(SDMMC1) #define __HAL_RCC_SDMMC1_CLK_DISABLE() CLEAR_BIT(RCC->APB2ENR, RCC_APB2ENR_SDMMC1EN) #endif /* SDMMC1 */ #define __HAL_RCC_TIM1_CLK_DISABLE() CLEAR_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM1EN) #define __HAL_RCC_SPI1_CLK_DISABLE() CLEAR_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI1EN) #if defined(TIM8) #define __HAL_RCC_TIM8_CLK_DISABLE() CLEAR_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM8EN) #endif /* TIM8 */ #define __HAL_RCC_USART1_CLK_DISABLE() CLEAR_BIT(RCC->APB2ENR, RCC_APB2ENR_USART1EN) #define __HAL_RCC_TIM15_CLK_DISABLE() CLEAR_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM15EN) #define __HAL_RCC_TIM16_CLK_DISABLE() CLEAR_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM16EN) #if defined(TIM17) #define __HAL_RCC_TIM17_CLK_DISABLE() CLEAR_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM17EN) #endif /* TIM17 */ #define __HAL_RCC_SAI1_CLK_DISABLE() CLEAR_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI1EN) #if defined(SAI2) #define __HAL_RCC_SAI2_CLK_DISABLE() CLEAR_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI2EN) #endif /* SAI2 */ #if defined(DFSDM1_Filter0) #define __HAL_RCC_DFSDM1_CLK_DISABLE() CLEAR_BIT(RCC->APB2ENR, RCC_APB2ENR_DFSDM1EN) #endif /* DFSDM1_Filter0 */ /** * @} */ /** @defgroup RCC_AHB1_Peripheral_Clock_Enable_Disable_Status AHB1 Peripheral Clock Enabled or Disabled Status * @brief Check whether the AHB1 peripheral clock is enabled or not. * @note After reset, the peripheral clock (used for registers read/write access) * is disabled and the application software has to enable this clock before * using it. * @{ */ #define __HAL_RCC_DMA1_IS_CLK_ENABLED() (READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA1EN) != RESET) #define __HAL_RCC_DMA2_IS_CLK_ENABLED() (READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA2EN) != RESET) #define __HAL_RCC_FLASH_IS_CLK_ENABLED() (READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_FLASHEN) != RESET) #define __HAL_RCC_CRC_IS_CLK_ENABLED() (READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN) != RESET) #define __HAL_RCC_TSC_IS_CLK_ENABLED() (READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_TSCEN) != RESET) #define __HAL_RCC_DMA1_IS_CLK_DISABLED() (READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA1EN) == RESET) #define __HAL_RCC_DMA2_IS_CLK_DISABLED() (READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA2EN) == RESET) #define __HAL_RCC_FLASH_IS_CLK_DISABLED() (READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_FLASHEN) == RESET) #define __HAL_RCC_CRC_IS_CLK_DISABLED() (READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN) == RESET) #define __HAL_RCC_TSC_IS_CLK_DISABLED() (READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_TSCEN) == RESET) /** * @} */ /** @defgroup RCC_AHB2_Clock_Enable_Disable_Status AHB2 Peripheral Clock Enabled or Disabled Status * @brief Check whether the AHB2 peripheral clock is enabled or not. * @note After reset, the peripheral clock (used for registers read/write access) * is disabled and the application software has to enable this clock before * using it. * @{ */ #define __HAL_RCC_GPIOA_IS_CLK_ENABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOAEN) != RESET) #define __HAL_RCC_GPIOB_IS_CLK_ENABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOCEN) != RESET) #define __HAL_RCC_GPIOC_IS_CLK_ENABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOCEN) != RESET) #if defined(GPIOD) #define __HAL_RCC_GPIOD_IS_CLK_ENABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIODEN) != RESET) #endif /* GPIOD */ #if defined(GPIOE) #define __HAL_RCC_GPIOE_IS_CLK_ENABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOEEN) != RESET) #endif /* GPIOE */ #if defined(GPIOF) #define __HAL_RCC_GPIOF_IS_CLK_ENABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOFEN) != RESET) #endif /* GPIOF */ #if defined(GPIOG) #define __HAL_RCC_GPIOG_IS_CLK_ENABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOGEN) != RESET) #endif /* GPIOG */ #define __HAL_RCC_GPIOH_IS_CLK_ENABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOHEN) != RESET) #if defined(USB_OTG_FS) #define __HAL_RCC_USB_OTG_FS_IS_CLK_ENABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_OTGFSEN) != RESET) #endif /* USB_OTG_FS */ #define __HAL_RCC_ADC_IS_CLK_ENABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_ADCEN) != RESET) #if defined(AES) #define __HAL_RCC_AES_IS_CLK_ENABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_AESEN) != RESET) #endif /* AES */ #define __HAL_RCC_RNG_IS_CLK_ENABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN) != RESET) #define __HAL_RCC_GPIOA_IS_CLK_DISABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOAEN) == RESET) #define __HAL_RCC_GPIOB_IS_CLK_DISABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOBEN) == RESET) #define __HAL_RCC_GPIOC_IS_CLK_DISABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOCEN) == RESET) #if defined(GPIOD) #define __HAL_RCC_GPIOD_IS_CLK_DISABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIODEN) == RESET) #endif /* GPIOD */ #if defined(GPIOE) #define __HAL_RCC_GPIOE_IS_CLK_DISABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOEEN) == RESET) #endif /* GPIOE */ #if defined(GPIOF) #define __HAL_RCC_GPIOF_IS_CLK_DISABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOFEN) == RESET) #endif /* GPIOF */ #if defined(GPIOG) #define __HAL_RCC_GPIOG_IS_CLK_DISABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOGEN) == RESET) #endif /* GPIOG */ #define __HAL_RCC_GPIOH_IS_CLK_DISABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOHEN) == RESET) #if defined(USB_OTG_FS) #define __HAL_RCC_USB_OTG_FS_IS_CLK_DISABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_OTGFSEN) == RESET) #endif /* USB_OTG_FS */ #define __HAL_RCC_ADC_IS_CLK_DISABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_ADCEN) == RESET) #if defined(AES) #define __HAL_RCC_AES_IS_CLK_DISABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_AESEN) == RESET) #endif /* AES */ #define __HAL_RCC_RNG_IS_CLK_DISABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN) == RESET) /** * @} */ /** @defgroup RCC_AHB3_Clock_Enable_Disable_Status AHB3 Peripheral Clock Enabled or Disabled Status * @brief Check whether the AHB3 peripheral clock is enabled or not. * @note After reset, the peripheral clock (used for registers read/write access) * is disabled and the application software has to enable this clock before * using it. * @{ */ #if defined(FMC_BANK1) #define __HAL_RCC_FMC_IS_CLK_ENABLED() (READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN) != RESET) #endif /* FMC_BANK1 */ #if defined(QUADSPI) #define __HAL_RCC_QSPI_IS_CLK_ENABLED() (READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_QSPIEN) != RESET) #endif /* QUADSPI */ #if defined(FMC_BANK1) #define __HAL_RCC_FMC_IS_CLK_DISABLED() (READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN) == RESET) #endif /* FMC_BANK1 */ #if defined(QUADSPI) #define __HAL_RCC_QSPI_IS_CLK_DISABLED() (READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_QSPIEN) == RESET) #endif /* QUADSPI */ /** * @} */ /** @defgroup RCC_APB1_Clock_Enable_Disable_Status APB1 Peripheral Clock Enabled or Disabled Status * @brief Check whether the APB1 peripheral clock is enabled or not. * @note After reset, the peripheral clock (used for registers read/write access) * is disabled and the application software has to enable this clock before * using it. * @{ */ #define __HAL_RCC_TIM2_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM2EN) != RESET) #if defined(TIM3) #define __HAL_RCC_TIM3_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM3EN) != RESET) #endif /* TIM3 */ #if defined(TIM4) #define __HAL_RCC_TIM4_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM4EN) != RESET) #endif /* TIM4 */ #if defined(TIM5) #define __HAL_RCC_TIM5_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM5EN) != RESET) #endif /* TIM5 */ #define __HAL_RCC_TIM6_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM6EN) != RESET) #define __HAL_RCC_TIM7_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM7EN) != RESET) #if defined(LCD) #define __HAL_RCC_LCD_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_LCDEN) != RESET) #endif /* LCD */ #if defined(RCC_APB1ENR1_RTCAPBEN) #define __HAL_RCC_RTCAPB_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_RTCAPBEN) != RESET) #endif /* RCC_APB1ENR1_RTCAPBEN */ #define __HAL_RCC_WWDG_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_WWDGEN) != RESET) #if defined(SPI2) #define __HAL_RCC_SPI2_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_SPI2EN) != RESET) #endif /* SPI2 */ #define __HAL_RCC_SPI3_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_SPI3EN) != RESET) #define __HAL_RCC_USART2_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_USART2EN) != RESET) #if defined(USART3) #define __HAL_RCC_USART3_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_USART3EN) != RESET) #endif /* USART3 */ #if defined(UART4) #define __HAL_RCC_UART4_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_UART4EN) != RESET) #endif /* UART4 */ #if defined(UART5) #define __HAL_RCC_UART5_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_UART5EN) != RESET) #endif /* UART5 */ #define __HAL_RCC_I2C1_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C1EN) != RESET) #if defined(I2C2) #define __HAL_RCC_I2C2_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C2EN) != RESET) #endif /* I2C2 */ #define __HAL_RCC_I2C3_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C3EN) != RESET) #if defined(I2C4) #define __HAL_RCC_I2C4_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR2, RCC_APB1ENR2_I2C4EN) != RESET) #endif /* I2C4 */ #if defined(CRS) #define __HAL_RCC_CRS_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_CRSEN) != RESET) #endif /* CRS */ #define __HAL_RCC_CAN1_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_CAN1EN) != RESET) #if defined(USB) #define __HAL_RCC_USB_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_USBFSEN) != RESET) #endif /* USB */ #define __HAL_RCC_PWR_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_PWREN) != RESET) #define __HAL_RCC_DAC1_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_DAC1EN) != RESET) #define __HAL_RCC_OPAMP_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_OPAMPEN) != RESET) #define __HAL_RCC_LPTIM1_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_LPTIM1EN) != RESET) #define __HAL_RCC_LPUART1_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR2, RCC_APB1ENR2_LPUART1EN) != RESET) #if defined(SWPMI1) #define __HAL_RCC_SWPMI1_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR2, RCC_APB1ENR2_SWPMI1EN) != RESET) #endif /* SWPMI1 */ #define __HAL_RCC_LPTIM2_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR2, RCC_APB1ENR2_LPTIM2EN) != RESET) #define __HAL_RCC_TIM2_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM2EN) == RESET) #if defined(TIM3) #define __HAL_RCC_TIM3_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM3EN) == RESET) #endif /* TIM3 */ #if defined(TIM4) #define __HAL_RCC_TIM4_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM4EN) == RESET) #endif /* TIM4 */ #if defined(TIM5) #define __HAL_RCC_TIM5_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM5EN) == RESET) #endif /* TIM5 */ #define __HAL_RCC_TIM6_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM6EN) == RESET) #define __HAL_RCC_TIM7_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM7EN) == RESET) #if defined(LCD) #define __HAL_RCC_LCD_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_LCDEN) == RESET) #endif /* LCD */ #if defined(RCC_APB1ENR1_RTCAPBEN) #define __HAL_RCC_RTCAPB_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_RTCAPBEN) == RESET) #endif /* RCC_APB1ENR1_RTCAPBEN */ #define __HAL_RCC_WWDG_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_WWDGEN) == RESET) #if defined(SPI2) #define __HAL_RCC_SPI2_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_SPI2EN) == RESET) #endif /* SPI2 */ #define __HAL_RCC_SPI3_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_SPI3EN) == RESET) #define __HAL_RCC_USART2_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_USART2EN) == RESET) #if defined(USART3) #define __HAL_RCC_USART3_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_USART3EN) == RESET) #endif /* USART3 */ #if defined(UART4) #define __HAL_RCC_UART4_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_UART4EN) == RESET) #endif /* UART4 */ #if defined(UART5) #define __HAL_RCC_UART5_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_UART5EN) == RESET) #endif /* UART5 */ #define __HAL_RCC_I2C1_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C1EN) == RESET) #if defined(I2C2) #define __HAL_RCC_I2C2_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C2EN) == RESET) #endif /* I2C2 */ #define __HAL_RCC_I2C3_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C3EN) == RESET) #if defined(I2C4) #define __HAL_RCC_I2C4_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR2, RCC_APB1ENR2_I2C4EN) == RESET) #endif /* I2C4 */ #if defined(CRS) #define __HAL_RCC_CRS_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_CRSEN) == RESET) #endif /* CRS */ #define __HAL_RCC_CAN1_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_CAN1EN) == RESET) #if defined(USB) #define __HAL_RCC_USB_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_USBFSEN) == RESET) #endif /* USB */ #define __HAL_RCC_PWR_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_PWREN) == RESET) #define __HAL_RCC_DAC1_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_DAC1EN) == RESET) #define __HAL_RCC_OPAMP_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_OPAMPEN) == RESET) #define __HAL_RCC_LPTIM1_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_LPTIM1EN) == RESET) #define __HAL_RCC_LPUART1_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR2, RCC_APB1ENR2_LPUART1EN) == RESET) #if defined(SWPMI1) #define __HAL_RCC_SWPMI1_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR2, RCC_APB1ENR2_SWPMI1EN) == RESET) #endif /* SWPMI1 */ #define __HAL_RCC_LPTIM2_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR2, RCC_APB1ENR2_LPTIM2EN) == RESET) /** * @} */ /** @defgroup RCC_APB2_Clock_Enable_Disable_Status APB2 Peripheral Clock Enabled or Disabled Status * @brief Check whether the APB2 peripheral clock is enabled or not. * @note After reset, the peripheral clock (used for registers read/write access) * is disabled and the application software has to enable this clock before * using it. * @{ */ #define __HAL_RCC_SYSCFG_IS_CLK_ENABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SYSCFGEN) != RESET) #define __HAL_RCC_FIREWALL_IS_CLK_ENABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_FWEN) != RESET) #if defined(SDMMC1) #define __HAL_RCC_SDMMC1_IS_CLK_ENABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SDMMC1EN) != RESET) #endif /* SDMMC1 */ #define __HAL_RCC_TIM1_IS_CLK_ENABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM1EN) != RESET) #define __HAL_RCC_SPI1_IS_CLK_ENABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI1EN) != RESET) #if defined(TIM8) #define __HAL_RCC_TIM8_IS_CLK_ENABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM8EN) != RESET) #endif /* TIM8 */ #define __HAL_RCC_USART1_IS_CLK_ENABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_USART1EN) != RESET) #define __HAL_RCC_TIM15_IS_CLK_ENABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM15EN) != RESET) #define __HAL_RCC_TIM16_IS_CLK_ENABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM16EN) != RESET) #if defined(TIM17) #define __HAL_RCC_TIM17_IS_CLK_ENABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM17EN) != RESET) #endif /* TIM17 */ #define __HAL_RCC_SAI1_IS_CLK_ENABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI1EN) != RESET) #if defined(SAI2) #define __HAL_RCC_SAI2_IS_CLK_ENABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI2EN) != RESET) #endif /* SAI2 */ #if defined(DFSDM1_Filter0) #define __HAL_RCC_DFSDM1_IS_CLK_ENABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_DFSDM1EN) != RESET) #endif /* DFSDM1_Filter0 */ #define __HAL_RCC_SYSCFG_IS_CLK_DISABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SYSCFGEN) == RESET) #if defined(SDMMC1) #define __HAL_RCC_SDMMC1_IS_CLK_DISABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SDMMC1EN) == RESET) #endif /* SDMMC1 */ #define __HAL_RCC_TIM1_IS_CLK_DISABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM1EN) == RESET) #define __HAL_RCC_SPI1_IS_CLK_DISABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI1EN) == RESET) #if defined(TIM8) #define __HAL_RCC_TIM8_IS_CLK_DISABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM8EN) == RESET) #endif /* TIM8 */ #define __HAL_RCC_USART1_IS_CLK_DISABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_USART1EN) == RESET) #define __HAL_RCC_TIM15_IS_CLK_DISABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM15EN) == RESET) #define __HAL_RCC_TIM16_IS_CLK_DISABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM16EN) == RESET) #if defined(TIM17) #define __HAL_RCC_TIM17_IS_CLK_DISABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM17EN) == RESET) #endif /* TIM17 */ #define __HAL_RCC_SAI1_IS_CLK_DISABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI1EN) == RESET) #if defined(SAI2) #define __HAL_RCC_SAI2_IS_CLK_DISABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI2EN) == RESET) #endif /* SAI2 */ #if defined(DFSDM1_Filter0) #define __HAL_RCC_DFSDM1_IS_CLK_DISABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_DFSDM1EN) == RESET) #endif /* DFSDM1_Filter0 */ /** * @} */ /** @defgroup RCC_AHB1_Force_Release_Reset AHB1 Peripheral Force Release Reset * @brief Force or release AHB1 peripheral reset. * @{ */ #define __HAL_RCC_AHB1_FORCE_RESET() WRITE_REG(RCC->AHB1RSTR, 0xFFFFFFFFU) #define __HAL_RCC_DMA1_FORCE_RESET() SET_BIT(RCC->AHB1RSTR, RCC_AHB1RSTR_DMA1RST) #define __HAL_RCC_DMA2_FORCE_RESET() SET_BIT(RCC->AHB1RSTR, RCC_AHB1RSTR_DMA2RST) #define __HAL_RCC_FLASH_FORCE_RESET() SET_BIT(RCC->AHB1RSTR, RCC_AHB1RSTR_FLASHRST) #define __HAL_RCC_CRC_FORCE_RESET() SET_BIT(RCC->AHB1RSTR, RCC_AHB1RSTR_CRCRST) #define __HAL_RCC_TSC_FORCE_RESET() SET_BIT(RCC->AHB1RSTR, RCC_AHB1RSTR_TSCRST) #define __HAL_RCC_AHB1_RELEASE_RESET() WRITE_REG(RCC->AHB1RSTR, 0x00000000U) #define __HAL_RCC_DMA1_RELEASE_RESET() CLEAR_BIT(RCC->AHB1RSTR, RCC_AHB1RSTR_DMA1RST) #define __HAL_RCC_DMA2_RELEASE_RESET() CLEAR_BIT(RCC->AHB1RSTR, RCC_AHB1RSTR_DMA2RST) #define __HAL_RCC_FLASH_RELEASE_RESET() CLEAR_BIT(RCC->AHB1RSTR, RCC_AHB1RSTR_FLASHRST) #define __HAL_RCC_CRC_RELEASE_RESET() CLEAR_BIT(RCC->AHB1RSTR, RCC_AHB1RSTR_CRCRST) #define __HAL_RCC_TSC_RELEASE_RESET() CLEAR_BIT(RCC->AHB1RSTR, RCC_AHB1RSTR_TSCRST) /** * @} */ /** @defgroup RCC_AHB2_Force_Release_Reset AHB2 Peripheral Force Release Reset * @brief Force or release AHB2 peripheral reset. * @{ */ #define __HAL_RCC_AHB2_FORCE_RESET() WRITE_REG(RCC->AHB2RSTR, 0xFFFFFFFFU) #define __HAL_RCC_GPIOA_FORCE_RESET() SET_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIOARST) #define __HAL_RCC_GPIOB_FORCE_RESET() SET_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIOBRST) #define __HAL_RCC_GPIOC_FORCE_RESET() SET_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIOCRST) #if defined(GPIOD) #define __HAL_RCC_GPIOD_FORCE_RESET() SET_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIODRST) #endif /* GPIOD */ #if defined(GPIOE) #define __HAL_RCC_GPIOE_FORCE_RESET() SET_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIOERST) #endif /* GPIOE */ #if defined(GPIOF) #define __HAL_RCC_GPIOF_FORCE_RESET() SET_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIOFRST) #endif /* GPIOF */ #if defined(GPIOG) #define __HAL_RCC_GPIOG_FORCE_RESET() SET_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIOGRST) #endif /* GPIOG */ #define __HAL_RCC_GPIOH_FORCE_RESET() SET_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIOHRST) #if defined(USB_OTG_FS) #define __HAL_RCC_USB_OTG_FS_FORCE_RESET() SET_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_OTGFSRST) #endif /* USB_OTG_FS */ #define __HAL_RCC_ADC_FORCE_RESET() SET_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_ADCRST) #if defined(AES) #define __HAL_RCC_AES_FORCE_RESET() SET_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_AESRST) #endif /* AES */ #define __HAL_RCC_RNG_FORCE_RESET() SET_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_RNGRST) #define __HAL_RCC_AHB2_RELEASE_RESET() WRITE_REG(RCC->AHB2RSTR, 0x00000000U) #define __HAL_RCC_GPIOA_RELEASE_RESET() CLEAR_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIOARST) #define __HAL_RCC_GPIOB_RELEASE_RESET() CLEAR_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIOBRST) #define __HAL_RCC_GPIOC_RELEASE_RESET() CLEAR_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIOCRST) #if defined(GPIOD) #define __HAL_RCC_GPIOD_RELEASE_RESET() CLEAR_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIODRST) #endif /* GPIOD */ #if defined(GPIOE) #define __HAL_RCC_GPIOE_RELEASE_RESET() CLEAR_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIOERST) #endif /* GPIOE */ #if defined(GPIOF) #define __HAL_RCC_GPIOF_RELEASE_RESET() CLEAR_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIOFRST) #endif /* GPIOF */ #if defined(GPIOG) #define __HAL_RCC_GPIOG_RELEASE_RESET() CLEAR_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIOGRST) #endif /* GPIOG */ #define __HAL_RCC_GPIOH_RELEASE_RESET() CLEAR_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIOHRST) #if defined(USB_OTG_FS) #define __HAL_RCC_USB_OTG_FS_RELEASE_RESET() CLEAR_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_OTGFSRST) #endif /* USB_OTG_FS */ #define __HAL_RCC_ADC_RELEASE_RESET() CLEAR_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_ADCRST) #if defined(AES) #define __HAL_RCC_AES_RELEASE_RESET() CLEAR_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_AESRST) #endif /* AES */ #define __HAL_RCC_RNG_RELEASE_RESET() CLEAR_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_RNGRST) /** * @} */ /** @defgroup RCC_AHB3_Force_Release_Reset AHB3 Peripheral Force Release Reset * @brief Force or release AHB3 peripheral reset. * @{ */ #define __HAL_RCC_AHB3_FORCE_RESET() WRITE_REG(RCC->AHB3RSTR, 0xFFFFFFFFU) #if defined(FMC_BANK1) #define __HAL_RCC_FMC_FORCE_RESET() SET_BIT(RCC->AHB3RSTR, RCC_AHB3RSTR_FMCRST) #endif /* FMC_BANK1 */ #if defined(QUADSPI) #define __HAL_RCC_QSPI_FORCE_RESET() SET_BIT(RCC->AHB3RSTR, RCC_AHB3RSTR_QSPIRST) #endif /* QUADSPI */ #define __HAL_RCC_AHB3_RELEASE_RESET() WRITE_REG(RCC->AHB3RSTR, 0x00000000U) #if defined(FMC_BANK1) #define __HAL_RCC_FMC_RELEASE_RESET() CLEAR_BIT(RCC->AHB3RSTR, RCC_AHB3RSTR_FMCRST) #endif /* FMC_BANK1 */ #if defined(QUADSPI) #define __HAL_RCC_QSPI_RELEASE_RESET() CLEAR_BIT(RCC->AHB3RSTR, RCC_AHB3RSTR_QSPIRST) #endif /* QUADSPI */ /** * @} */ /** @defgroup RCC_APB1_Force_Release_Reset APB1 Peripheral Force Release Reset * @brief Force or release APB1 peripheral reset. * @{ */ #define __HAL_RCC_APB1_FORCE_RESET() WRITE_REG(RCC->APB1RSTR1, 0xFFFFFFFFU) #define __HAL_RCC_TIM2_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_TIM2RST) #if defined(TIM3) #define __HAL_RCC_TIM3_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_TIM3RST) #endif /* TIM3 */ #if defined(TIM4) #define __HAL_RCC_TIM4_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_TIM4RST) #endif /* TIM4 */ #if defined(TIM5) #define __HAL_RCC_TIM5_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_TIM5RST) #endif /* TIM5 */ #define __HAL_RCC_TIM6_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_TIM6RST) #define __HAL_RCC_TIM7_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_TIM7RST) #if defined(LCD) #define __HAL_RCC_LCD_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_LCDRST) #endif /* LCD */ #if defined(SPI2) #define __HAL_RCC_SPI2_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_SPI2RST) #endif /* SPI2 */ #define __HAL_RCC_SPI3_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_SPI3RST) #define __HAL_RCC_USART2_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_USART2RST) #if defined(USART3) #define __HAL_RCC_USART3_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_USART3RST) #endif /* USART3 */ #if defined(UART4) #define __HAL_RCC_UART4_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_UART4RST) #endif /* UART4 */ #if defined(UART5) #define __HAL_RCC_UART5_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_UART5RST) #endif /* UART5 */ #define __HAL_RCC_I2C1_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_I2C1RST) #if defined(I2C2) #define __HAL_RCC_I2C2_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_I2C2RST) #endif /* I2C2 */ #define __HAL_RCC_I2C3_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_I2C3RST) #if defined(I2C4) #define __HAL_RCC_I2C4_FORCE_RESET() SET_BIT(RCC->APB1RSTR2, RCC_APB1RSTR2_I2C4RST) #endif /* I2C4 */ #if defined(CRS) #define __HAL_RCC_CRS_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_CRSRST) #endif /* CRS */ #define __HAL_RCC_CAN1_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_CAN1RST) #if defined(USB) #define __HAL_RCC_USB_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_USBFSRST) #endif /* USB */ #define __HAL_RCC_PWR_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_PWRRST) #define __HAL_RCC_DAC1_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_DAC1RST) #define __HAL_RCC_OPAMP_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_OPAMPRST) #define __HAL_RCC_LPTIM1_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_LPTIM1RST) #define __HAL_RCC_LPUART1_FORCE_RESET() SET_BIT(RCC->APB1RSTR2, RCC_APB1RSTR2_LPUART1RST) #if defined(SWPMI1) #define __HAL_RCC_SWPMI1_FORCE_RESET() SET_BIT(RCC->APB1RSTR2, RCC_APB1RSTR2_SWPMI1RST) #endif /* SWPMI1 */ #define __HAL_RCC_LPTIM2_FORCE_RESET() SET_BIT(RCC->APB1RSTR2, RCC_APB1RSTR2_LPTIM2RST) #define __HAL_RCC_APB1_RELEASE_RESET() WRITE_REG(RCC->APB1RSTR1, 0x00000000U) #define __HAL_RCC_TIM2_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_TIM2RST) #if defined(TIM3) #define __HAL_RCC_TIM3_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_TIM3RST) #endif /* TIM3 */ #if defined(TIM4) #define __HAL_RCC_TIM4_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_TIM4RST) #endif /* TIM4 */ #if defined(TIM5) #define __HAL_RCC_TIM5_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_TIM5RST) #endif /* TIM5 */ #define __HAL_RCC_TIM6_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_TIM6RST) #define __HAL_RCC_TIM7_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_TIM7RST) #if defined(LCD) #define __HAL_RCC_LCD_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_LCDRST) #endif /* LCD */ #if defined(SPI2) #define __HAL_RCC_SPI2_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_SPI2RST) #endif /* SPI2 */ #define __HAL_RCC_SPI3_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_SPI3RST) #define __HAL_RCC_USART2_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_USART2RST) #if defined(USART3) #define __HAL_RCC_USART3_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_USART3RST) #endif /* USART3 */ #if defined(UART4) #define __HAL_RCC_UART4_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_UART4RST) #endif /* UART4 */ #if defined(UART5) #define __HAL_RCC_UART5_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_UART5RST) #endif /* UART5 */ #define __HAL_RCC_I2C1_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_I2C1RST) #if defined(I2C2) #define __HAL_RCC_I2C2_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_I2C2RST) #endif /* I2C2 */ #define __HAL_RCC_I2C3_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_I2C3RST) #if defined(I2C4) #define __HAL_RCC_I2C4_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR2, RCC_APB1RSTR2_I2C4RST) #endif /* I2C4 */ #if defined(CRS) #define __HAL_RCC_CRS_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_CRSRST) #endif /* CRS */ #define __HAL_RCC_CAN1_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_CAN1RST) #if defined(USB) #define __HAL_RCC_USB_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_USBFSRST) #endif /* USB */ #define __HAL_RCC_PWR_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_PWRRST) #define __HAL_RCC_DAC1_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_DAC1RST) #define __HAL_RCC_OPAMP_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_OPAMPRST) #define __HAL_RCC_LPTIM1_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_LPTIM1RST) #define __HAL_RCC_LPUART1_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR2, RCC_APB1RSTR2_LPUART1RST) #if defined(SWPMI1) #define __HAL_RCC_SWPMI1_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR2, RCC_APB1RSTR2_SWPMI1RST) #endif /* SWPMI1 */ #define __HAL_RCC_LPTIM2_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR2, RCC_APB1RSTR2_LPTIM2RST) /** * @} */ /** @defgroup RCC_APB2_Force_Release_Reset APB2 Peripheral Force Release Reset * @brief Force or release APB2 peripheral reset. * @{ */ #define __HAL_RCC_APB2_FORCE_RESET() WRITE_REG(RCC->APB2RSTR, 0xFFFFFFFFU) #define __HAL_RCC_SYSCFG_FORCE_RESET() SET_BIT(RCC->APB2RSTR, RCC_APB2RSTR_SYSCFGRST) #if defined(SDMMC1) #define __HAL_RCC_SDMMC1_FORCE_RESET() SET_BIT(RCC->APB2RSTR, RCC_APB2RSTR_SDMMC1RST) #endif /* SDMMC1 */ #define __HAL_RCC_TIM1_FORCE_RESET() SET_BIT(RCC->APB2RSTR, RCC_APB2RSTR_TIM1RST) #define __HAL_RCC_SPI1_FORCE_RESET() SET_BIT(RCC->APB2RSTR, RCC_APB2RSTR_SPI1RST) #if defined(TIM8) #define __HAL_RCC_TIM8_FORCE_RESET() SET_BIT(RCC->APB2RSTR, RCC_APB2RSTR_TIM8RST) #endif /* TIM8 */ #define __HAL_RCC_USART1_FORCE_RESET() SET_BIT(RCC->APB2RSTR, RCC_APB2RSTR_USART1RST) #define __HAL_RCC_TIM15_FORCE_RESET() SET_BIT(RCC->APB2RSTR, RCC_APB2RSTR_TIM15RST) #define __HAL_RCC_TIM16_FORCE_RESET() SET_BIT(RCC->APB2RSTR, RCC_APB2RSTR_TIM16RST) #if defined(TIM17) #define __HAL_RCC_TIM17_FORCE_RESET() SET_BIT(RCC->APB2RSTR, RCC_APB2RSTR_TIM17RST) #endif /* TIM17 */ #define __HAL_RCC_SAI1_FORCE_RESET() SET_BIT(RCC->APB2RSTR, RCC_APB2RSTR_SAI1RST) #if defined(SAI2) #define __HAL_RCC_SAI2_FORCE_RESET() SET_BIT(RCC->APB2RSTR, RCC_APB2RSTR_SAI2RST) #endif /* SAI2 */ #if defined(DFSDM1_Filter0) #define __HAL_RCC_DFSDM1_FORCE_RESET() SET_BIT(RCC->APB2RSTR, RCC_APB2RSTR_DFSDM1RST) #endif /* DFSDM1_Filter0 */ #define __HAL_RCC_APB2_RELEASE_RESET() WRITE_REG(RCC->APB2RSTR, 0x00000000U) #define __HAL_RCC_SYSCFG_RELEASE_RESET() CLEAR_BIT(RCC->APB2RSTR, RCC_APB2RSTR_SYSCFGRST) #if defined(SDMMC1) #define __HAL_RCC_SDMMC1_RELEASE_RESET() CLEAR_BIT(RCC->APB2RSTR, RCC_APB2RSTR_SDMMC1RST) #endif /* SDMMC1 */ #define __HAL_RCC_TIM1_RELEASE_RESET() CLEAR_BIT(RCC->APB2RSTR, RCC_APB2RSTR_TIM1RST) #define __HAL_RCC_SPI1_RELEASE_RESET() CLEAR_BIT(RCC->APB2RSTR, RCC_APB2RSTR_SPI1RST) #if defined(TIM8) #define __HAL_RCC_TIM8_RELEASE_RESET() CLEAR_BIT(RCC->APB2RSTR, RCC_APB2RSTR_TIM8RST) #endif /* TIM8 */ #define __HAL_RCC_USART1_RELEASE_RESET() CLEAR_BIT(RCC->APB2RSTR, RCC_APB2RSTR_USART1RST) #define __HAL_RCC_TIM15_RELEASE_RESET() CLEAR_BIT(RCC->APB2RSTR, RCC_APB2RSTR_TIM15RST) #define __HAL_RCC_TIM16_RELEASE_RESET() CLEAR_BIT(RCC->APB2RSTR, RCC_APB2RSTR_TIM16RST) #if defined(TIM17) #define __HAL_RCC_TIM17_RELEASE_RESET() CLEAR_BIT(RCC->APB2RSTR, RCC_APB2RSTR_TIM17RST) #endif /* TIM17 */ #define __HAL_RCC_SAI1_RELEASE_RESET() CLEAR_BIT(RCC->APB2RSTR, RCC_APB2RSTR_SAI1RST) #if defined(SAI2) #define __HAL_RCC_SAI2_RELEASE_RESET() CLEAR_BIT(RCC->APB2RSTR, RCC_APB2RSTR_SAI2RST) #endif /* SAI2 */ #if defined(DFSDM1_Filter0) #define __HAL_RCC_DFSDM1_RELEASE_RESET() CLEAR_BIT(RCC->APB2RSTR, RCC_APB2RSTR_DFSDM1RST) #endif /* DFSDM1_Filter0 */ /** * @} */ /** @defgroup RCC_AHB1_Clock_Sleep_Enable_Disable AHB1 Peripheral Clock Sleep Enable Disable * @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode. * @note Peripheral clock gating in SLEEP mode can be used to further reduce * power consumption. * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. * @note By default, all peripheral clocks are enabled during SLEEP mode. * @{ */ #define __HAL_RCC_DMA1_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_DMA1SMEN) #define __HAL_RCC_DMA2_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_DMA2SMEN) #define __HAL_RCC_FLASH_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_FLASHSMEN) #define __HAL_RCC_SRAM1_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_SRAM1SMEN) #define __HAL_RCC_CRC_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_CRCSMEN) #define __HAL_RCC_TSC_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_TSCSMEN) #define __HAL_RCC_DMA1_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_DMA1SMEN) #define __HAL_RCC_DMA2_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_DMA2SMEN) #define __HAL_RCC_FLASH_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_FLASHSMEN) #define __HAL_RCC_SRAM1_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_SRAM1SMEN) #define __HAL_RCC_CRC_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_CRCSMEN) #define __HAL_RCC_TSC_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_TSCSMEN) /** * @} */ /** @defgroup RCC_AHB2_Clock_Sleep_Enable_Disable AHB2 Peripheral Clock Sleep Enable Disable * @brief Enable or disable the AHB2 peripheral clock during Low Power (Sleep) mode. * @note Peripheral clock gating in SLEEP mode can be used to further reduce * power consumption. * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. * @note By default, all peripheral clocks are enabled during SLEEP mode. * @{ */ #define __HAL_RCC_GPIOA_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOASMEN) #define __HAL_RCC_GPIOB_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOBSMEN) #define __HAL_RCC_GPIOC_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOCSMEN) #if defined(GPIOD) #define __HAL_RCC_GPIOD_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIODSMEN) #endif /* GPIOD */ #if defined(GPIOE) #define __HAL_RCC_GPIOE_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOESMEN) #endif /* GPIOE */ #if defined(GPIOF) #define __HAL_RCC_GPIOF_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOFSMEN) #endif /* GPIOF */ #if defined(GPIOG) #define __HAL_RCC_GPIOG_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOGSMEN) #endif /* GPIOG */ #define __HAL_RCC_GPIOH_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOHSMEN) #define __HAL_RCC_SRAM2_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_SRAM2SMEN) #if defined(USB_OTG_FS) #define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_OTGFSSMEN) #endif /* USB_OTG_FS */ #define __HAL_RCC_ADC_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_ADCSMEN) #if defined(AES) #define __HAL_RCC_AES_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_AESSMEN) #endif /* AES */ #define __HAL_RCC_RNG_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_RNGSMEN) #define __HAL_RCC_GPIOA_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOASMEN) #define __HAL_RCC_GPIOB_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOBSMEN) #define __HAL_RCC_GPIOC_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOCSMEN) #if defined(GPIOD) #define __HAL_RCC_GPIOD_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIODSMEN) #endif /* GPIOD */ #if defined(GPIOE) #define __HAL_RCC_GPIOE_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOESMEN) #endif /* GPIOE */ #if defined(GPIOF) #define __HAL_RCC_GPIOF_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOFSMEN) #endif /* GPIOF */ #if defined(GPIOG) #define __HAL_RCC_GPIOG_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOGSMEN) #endif /* GPIOG */ #define __HAL_RCC_GPIOH_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOHSMEN) #define __HAL_RCC_SRAM2_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_SRAM2SMEN) #if defined(USB_OTG_FS) #define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_OTGFSSMEN) #endif /* USB_OTG_FS */ #define __HAL_RCC_ADC_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_ADCSMEN) #if defined(AES) #define __HAL_RCC_AES_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_AESSMEN) #endif /* AES */ #define __HAL_RCC_RNG_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_RNGSMEN) /** * @} */ /** @defgroup RCC_AHB3_Clock_Sleep_Enable_Disable AHB3 Peripheral Clock Sleep Enable Disable * @brief Enable or disable the AHB3 peripheral clock during Low Power (Sleep) mode. * @note Peripheral clock gating in SLEEP mode can be used to further reduce * power consumption. * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. * @note By default, all peripheral clocks are enabled during SLEEP mode. * @{ */ #if defined(QUADSPI) #define __HAL_RCC_QSPI_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB3SMENR, RCC_AHB3SMENR_QSPISMEN) #endif /* QUADSPI */ #if defined(FMC_BANK1) #define __HAL_RCC_FMC_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB3SMENR, RCC_AHB3SMENR_FMCSMEN) #endif /* FMC_BANK1 */ #if defined(QUADSPI) #define __HAL_RCC_QSPI_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB3SMENR, RCC_AHB3SMENR_QSPISMEN) #endif /* QUADSPI */ #if defined(FMC_BANK1) #define __HAL_RCC_FMC_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB3SMENR, RCC_AHB3SMENR_FMCSMEN) #endif /* FMC_BANK1 */ /** * @} */ /** @defgroup RCC_APB1_Clock_Sleep_Enable_Disable APB1 Peripheral Clock Sleep Enable Disable * @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode. * @note Peripheral clock gating in SLEEP mode can be used to further reduce * power consumption. * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. * @note By default, all peripheral clocks are enabled during SLEEP mode. * @{ */ #define __HAL_RCC_TIM2_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM2SMEN) #if defined(TIM3) #define __HAL_RCC_TIM3_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM3SMEN) #endif /* TIM3 */ #if defined(TIM4) #define __HAL_RCC_TIM4_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM4SMEN) #endif /* TIM4 */ #if defined(TIM5) #define __HAL_RCC_TIM5_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM5SMEN) #endif /* TIM5 */ #define __HAL_RCC_TIM6_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM6SMEN) #define __HAL_RCC_TIM7_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM7SMEN) #if defined(LCD) #define __HAL_RCC_LCD_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_LCDSMEN) #endif /* LCD */ #if defined(RCC_APB1SMENR1_RTCAPBSMEN) #define __HAL_RCC_RTCAPB_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_RTCAPBSMEN) #endif /* RCC_APB1SMENR1_RTCAPBSMEN */ #define __HAL_RCC_WWDG_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_WWDGSMEN) #if defined(SPI2) #define __HAL_RCC_SPI2_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_SPI2SMEN) #endif /* SPI2 */ #define __HAL_RCC_SPI3_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_SPI3SMEN) #define __HAL_RCC_USART2_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_USART2SMEN) #if defined(USART3) #define __HAL_RCC_USART3_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_USART3SMEN) #endif /* USART3 */ #if defined(UART4) #define __HAL_RCC_UART4_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_UART4SMEN) #endif /* UART4 */ #if defined(UART5) #define __HAL_RCC_UART5_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_UART5SMEN) #endif /* UART5 */ #define __HAL_RCC_I2C1_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_I2C1SMEN) #if defined(I2C2) #define __HAL_RCC_I2C2_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_I2C2SMEN) #endif /* I2C2 */ #define __HAL_RCC_I2C3_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_I2C3SMEN) #if defined(I2C4) #define __HAL_RCC_I2C4_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_I2C4SMEN) #endif /* I2C4 */ #if defined(CRS) #define __HAL_RCC_CRS_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_CRSSMEN) #endif /* CRS */ #define __HAL_RCC_CAN1_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_CAN1SMEN) #if defined(USB) #define __HAL_RCC_USB_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_USBFSSMEN) #endif /* USB */ #define __HAL_RCC_PWR_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_PWRSMEN) #define __HAL_RCC_DAC1_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_DAC1SMEN) #define __HAL_RCC_OPAMP_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_OPAMPSMEN) #define __HAL_RCC_LPTIM1_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_LPTIM1SMEN) #define __HAL_RCC_LPUART1_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_LPUART1SMEN) #if defined(SWPMI1) #define __HAL_RCC_SWPMI1_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_SWPMI1SMEN) #endif /* SWPMI1 */ #define __HAL_RCC_LPTIM2_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_LPTIM2SMEN) #define __HAL_RCC_TIM2_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM2SMEN) #if defined(TIM3) #define __HAL_RCC_TIM3_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM3SMEN) #endif /* TIM3 */ #if defined(TIM4) #define __HAL_RCC_TIM4_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM4SMEN) #endif /* TIM4 */ #if defined(TIM5) #define __HAL_RCC_TIM5_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM5SMEN) #endif /* TIM5 */ #define __HAL_RCC_TIM6_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM6SMEN) #define __HAL_RCC_TIM7_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM7SMEN) #if defined(LCD) #define __HAL_RCC_LCD_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_LCDSMEN) #endif /* LCD */ #if defined(RCC_APB1SMENR1_RTCAPBSMEN) #define __HAL_RCC_RTCAPB_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_RTCAPBSMEN) #endif /* RCC_APB1SMENR1_RTCAPBSMEN */ #define __HAL_RCC_WWDG_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_WWDGSMEN) #if defined(SPI2) #define __HAL_RCC_SPI2_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_SPI2SMEN) #endif /* SPI2 */ #define __HAL_RCC_SPI3_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_SPI3SMEN) #define __HAL_RCC_USART2_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_USART2SMEN) #if defined(USART3) #define __HAL_RCC_USART3_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_USART3SMEN) #endif /* USART3 */ #if defined(UART4) #define __HAL_RCC_UART4_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_UART4SMEN) #endif /* UART4 */ #if defined(UART5) #define __HAL_RCC_UART5_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_UART5SMEN) #endif /* UART5 */ #define __HAL_RCC_I2C1_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_I2C1SMEN) #if defined(I2C2) #define __HAL_RCC_I2C2_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_I2C2SMEN) #endif /* I2C2 */ #define __HAL_RCC_I2C3_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_I2C3SMEN) #if defined(I2C4) #define __HAL_RCC_I2C4_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_I2C4SMEN) #endif /* I2C4 */ #if defined(CRS) #define __HAL_RCC_CRS_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_CRSSMEN) #endif /* CRS */ #define __HAL_RCC_CAN1_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_CAN1SMEN) #if defined(USB) #define __HAL_RCC_USB_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_USBFSSMEN) #endif /* USB */ #define __HAL_RCC_PWR_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_PWRSMEN) #define __HAL_RCC_DAC1_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_DAC1SMEN) #define __HAL_RCC_OPAMP_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_OPAMPSMEN) #define __HAL_RCC_LPTIM1_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_LPTIM1SMEN) #define __HAL_RCC_LPUART1_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_LPUART1SMEN) #if defined(SWPMI1) #define __HAL_RCC_SWPMI1_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_SWPMI1SMEN) #endif /* SWPMI1 */ #define __HAL_RCC_LPTIM2_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_LPTIM2SMEN) /** * @} */ /** @defgroup RCC_APB2_Clock_Sleep_Enable_Disable APB2 Peripheral Clock Sleep Enable Disable * @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode. * @note Peripheral clock gating in SLEEP mode can be used to further reduce * power consumption. * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. * @note By default, all peripheral clocks are enabled during SLEEP mode. * @{ */ #define __HAL_RCC_SYSCFG_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SYSCFGSMEN) #if defined(SDMMC1) #define __HAL_RCC_SDMMC1_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SDMMC1SMEN) #endif /* SDMMC1 */ #define __HAL_RCC_TIM1_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM1SMEN) #define __HAL_RCC_SPI1_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SPI1SMEN) #if defined(TIM8) #define __HAL_RCC_TIM8_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM8SMEN) #endif /* TIM8 */ #define __HAL_RCC_USART1_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB2SMENR, RCC_APB2SMENR_USART1SMEN) #define __HAL_RCC_TIM15_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM15SMEN) #define __HAL_RCC_TIM16_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM16SMEN) #if defined(TIM17) #define __HAL_RCC_TIM17_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM17SMEN) #endif /* TIM17 */ #define __HAL_RCC_SAI1_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SAI1SMEN) #if defined(SAI2) #define __HAL_RCC_SAI2_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SAI2SMEN) #endif /* SAI2 */ #if defined(DFSDM1_Filter0) #define __HAL_RCC_DFSDM1_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB2SMENR, RCC_APB2SMENR_DFSDM1SMEN) #endif /* DFSDM1_Filter0 */ #define __HAL_RCC_SYSCFG_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SYSCFGSMEN) #if defined(SDMMC1) #define __HAL_RCC_SDMMC1_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SDMMC1SMEN) #endif /* SDMMC1 */ #define __HAL_RCC_TIM1_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM1SMEN) #define __HAL_RCC_SPI1_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SPI1SMEN) #if defined(TIM8) #define __HAL_RCC_TIM8_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM8SMEN) #endif /* TIM8 */ #define __HAL_RCC_USART1_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB2SMENR, RCC_APB2SMENR_USART1SMEN) #define __HAL_RCC_TIM15_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM15SMEN) #define __HAL_RCC_TIM16_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM16SMEN) #if defined(TIM17) #define __HAL_RCC_TIM17_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM17SMEN) #endif /* TIM17 */ #define __HAL_RCC_SAI1_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SAI1SMEN) #if defined(SAI2) #define __HAL_RCC_SAI2_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SAI2SMEN) #endif /* SAI2 */ #if defined(DFSDM1_Filter0) #define __HAL_RCC_DFSDM1_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB2SMENR, RCC_APB2SMENR_DFSDM1SMEN) #endif /* DFSDM1_Filter0 */ /** * @} */ /** @defgroup RCC_AHB1_Clock_Sleep_Enable_Disable_Status AHB1 Peripheral Clock Sleep Enabled or Disabled Status * @brief Check whether the AHB1 peripheral clock during Low Power (Sleep) mode is enabled or not. * @note Peripheral clock gating in SLEEP mode can be used to further reduce * power consumption. * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. * @note By default, all peripheral clocks are enabled during SLEEP mode. * @{ */ #define __HAL_RCC_DMA1_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_DMA1SMEN) != RESET) #define __HAL_RCC_DMA2_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_DMA2SMEN) != RESET) #define __HAL_RCC_FLASH_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_FLASHSMEN) != RESET) #define __HAL_RCC_SRAM1_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_SRAM1SMEN) != RESET) #define __HAL_RCC_CRC_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_CRCSMEN) != RESET) #define __HAL_RCC_TSC_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_TSCSMEN) != RESET) #define __HAL_RCC_DMA1_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_DMA1SMEN) == RESET) #define __HAL_RCC_DMA2_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_DMA2SMEN) == RESET) #define __HAL_RCC_FLASH_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_FLASHSMEN) == RESET) #define __HAL_RCC_SRAM1_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_SRAM1SMEN) == RESET) #define __HAL_RCC_CRC_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_CRCSMEN) == RESET) #define __HAL_RCC_TSC_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_TSCSMEN) == RESET) /** * @} */ /** @defgroup RCC_AHB2_Clock_Sleep_Enable_Disable_Status AHB2 Peripheral Clock Sleep Enabled or Disabled Status * @brief Check whether the AHB2 peripheral clock during Low Power (Sleep) mode is enabled or not. * @note Peripheral clock gating in SLEEP mode can be used to further reduce * power consumption. * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. * @note By default, all peripheral clocks are enabled during SLEEP mode. * @{ */ #define __HAL_RCC_GPIOA_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOASMEN) != RESET) #define __HAL_RCC_GPIOB_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOBSMEN) != RESET) #define __HAL_RCC_GPIOC_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOCSMEN) != RESET) #if defined(GPIOD) #define __HAL_RCC_GPIOD_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIODSMEN) != RESET) #endif /* GPIOD */ #if defined(GPIOE) #define __HAL_RCC_GPIOE_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOESMEN) != RESET) #endif /* GPIOE */ #if defined(GPIOF) #define __HAL_RCC_GPIOF_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOFSMEN) != RESET) #endif /* GPIOF */ #if defined(GPIOG) #define __HAL_RCC_GPIOG_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOGSMEN) != RESET) #endif /* GPIOG */ #define __HAL_RCC_GPIOH_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOHSMEN) != RESET) #define __HAL_RCC_SRAM2_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_SRAM2SMEN) != RESET) #if defined(USB_OTG_FS) #define __HAL_RCC_USB_OTG_FS_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_OTGFSSMEN) != RESET) #endif /* USB_OTG_FS */ #define __HAL_RCC_ADC_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_ADCSMEN) != RESET) #if defined(AES) #define __HAL_RCC_AES_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_AESSMEN) != RESET) #endif /* AES */ #define __HAL_RCC_RNG_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_RNGSMEN) != RESET) #define __HAL_RCC_GPIOA_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOASMEN) == RESET) #define __HAL_RCC_GPIOB_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOBSMEN) == RESET) #define __HAL_RCC_GPIOC_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOCSMEN) == RESET) #if defined(GPIOD) #define __HAL_RCC_GPIOD_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIODSMEN) == RESET) #endif /* GPIOD */ #if defined(GPIOE) #define __HAL_RCC_GPIOE_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOESMEN) == RESET) #endif /* GPIOE */ #if defined(GPIOF) #define __HAL_RCC_GPIOF_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOFSMEN) == RESET) #endif /* GPIOF */ #if defined(GPIOG) #define __HAL_RCC_GPIOG_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOGSMEN) == RESET) #endif /* GPIOG */ #define __HAL_RCC_GPIOH_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOHSMEN) == RESET) #define __HAL_RCC_SRAM2_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_SRAM2SMEN) == RESET) #if defined(USB_OTG_FS) #define __HAL_RCC_USB_OTG_FS_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_OTGFSSMEN) == RESET) #endif /* USB_OTG_FS */ #define __HAL_RCC_ADC_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_ADCSMEN) == RESET) #if defined(AES) #define __HAL_RCC_AES_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_AESSMEN) == RESET) #endif /* AES */ #define __HAL_RCC_RNG_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_RNGSMEN) == RESET) /** * @} */ /** @defgroup RCC_AHB3_Clock_Sleep_Enable_Disable_Status AHB3 Peripheral Clock Sleep Enabled or Disabled Status * @brief Check whether the AHB3 peripheral clock during Low Power (Sleep) mode is enabled or not. * @note Peripheral clock gating in SLEEP mode can be used to further reduce * power consumption. * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. * @note By default, all peripheral clocks are enabled during SLEEP mode. * @{ */ #if defined(QUADSPI) #define __HAL_RCC_QSPI_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB3SMENR, RCC_AHB3SMENR_QSPISMEN) != RESET) #endif /* QUADSPI */ #if defined(FMC_BANK1) #define __HAL_RCC_FMC_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB3SMENR, RCC_AHB3SMENR_FMCSMEN) != RESET) #endif /* FMC_BANK1 */ #if defined(QUADSPI) #define __HAL_RCC_QSPI_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB3SMENR, RCC_AHB3SMENR_QSPISMEN) == RESET) #endif /* QUADSPI */ #if defined(FMC_BANK1) #define __HAL_RCC_FMC_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB3SMENR, RCC_AHB3SMENR_FMCSMEN) == RESET) #endif /* FMC_BANK1 */ /** * @} */ /** @defgroup RCC_APB1_Clock_Sleep_Enable_Disable_Status APB1 Peripheral Clock Sleep Enabled or Disabled Status * @brief Check whether the APB1 peripheral clock during Low Power (Sleep) mode is enabled or not. * @note Peripheral clock gating in SLEEP mode can be used to further reduce * power consumption. * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. * @note By default, all peripheral clocks are enabled during SLEEP mode. * @{ */ #define __HAL_RCC_TIM2_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM2SMEN) != RESET) #if defined(TIM3) #define __HAL_RCC_TIM3_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM3SMEN) != RESET) #endif /* TIM3 */ #if defined(TIM4) #define __HAL_RCC_TIM4_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM4SMEN) != RESET) #endif /* TIM4 */ #if defined(TIM5) #define __HAL_RCC_TIM5_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM5SMEN) != RESET) #endif /* TIM5 */ #define __HAL_RCC_TIM6_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM6SMEN) != RESET) #define __HAL_RCC_TIM7_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM7SMEN) != RESET) #if defined(LCD) #define __HAL_RCC_LCD_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_LCDSMEN) != RESET) #endif /* LCD */ #if defined(RCC_APB1SMENR1_RTCAPBSMEN) #define __HAL_RCC_RTCAPB_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_RTCAPBSMEN) != RESET) #endif /* RCC_APB1SMENR1_RTCAPBSMEN */ #define __HAL_RCC_WWDG_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_WWDGSMEN) != RESET) #if defined(SPI2) #define __HAL_RCC_SPI2_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_SPI2SMEN) != RESET) #endif /* SPI2 */ #define __HAL_RCC_SPI3_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_SPI3SMEN) != RESET) #define __HAL_RCC_USART2_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_USART2SMEN) != RESET) #if defined(USART3) #define __HAL_RCC_USART3_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_USART3SMEN) != RESET) #endif /* USART3 */ #if defined(UART4) #define __HAL_RCC_UART4_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_UART4SMEN) != RESET) #endif /* UART4 */ #if defined(UART5) #define __HAL_RCC_UART5_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_UART5SMEN) != RESET) #endif /* UART5 */ #define __HAL_RCC_I2C1_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_I2C1SMEN) != RESET) #if defined(I2C2) #define __HAL_RCC_I2C2_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_I2C2SMEN) != RESET) #endif /* I2C2 */ #define __HAL_RCC_I2C3_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_I2C3SMEN) != RESET) #if defined(I2C4) #define __HAL_RCC_I2C4_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_I2C4SMEN) != RESET) #endif /* I2C4 */ #if defined(CRS) #define __HAL_RCC_CRS_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_CRSSMEN) != RESET) #endif /* CRS */ #define __HAL_RCC_CAN1_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_CAN1SMEN) != RESET) #if defined(USB) #define __HAL_RCC_USB_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_USBFSSMEN) != RESET) #endif /* USB */ #define __HAL_RCC_PWR_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_PWRSMEN) != RESET) #define __HAL_RCC_DAC1_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_DAC1SMEN) != RESET) #define __HAL_RCC_OPAMP_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_OPAMPSMEN) != RESET) #define __HAL_RCC_LPTIM1_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_LPTIM1SMEN) != RESET) #define __HAL_RCC_LPUART1_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_LPUART1SMEN) != RESET) #if defined(SWPMI1) #define __HAL_RCC_SWPMI1_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_SWPMI1SMEN) != RESET) #endif /* SWPMI1 */ #define __HAL_RCC_LPTIM2_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_LPTIM2SMEN) != RESET) #define __HAL_RCC_TIM2_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM2SMEN) == RESET) #if defined(TIM3) #define __HAL_RCC_TIM3_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM3SMEN) == RESET) #endif /* TIM3 */ #if defined(TIM4) #define __HAL_RCC_TIM4_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM4SMEN) == RESET) #endif /* TIM4 */ #if defined(TIM5) #define __HAL_RCC_TIM5_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM5SMEN) == RESET) #endif /* TIM5 */ #define __HAL_RCC_TIM6_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM6SMEN) == RESET) #define __HAL_RCC_TIM7_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM7SMEN) == RESET) #if defined(LCD) #define __HAL_RCC_LCD_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_LCDSMEN) == RESET) #endif /* LCD */ #if defined(RCC_APB1SMENR1_RTCAPBSMEN) #define __HAL_RCC_RTCAPB_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_RTCAPBSMEN) == RESET) #endif /* RCC_APB1SMENR1_RTCAPBSMEN */ #define __HAL_RCC_WWDG_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_WWDGSMEN) == RESET) #if defined(SPI2) #define __HAL_RCC_SPI2_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_SPI2SMEN) == RESET) #endif /* SPI2 */ #define __HAL_RCC_SPI3_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_SPI3SMEN) == RESET) #define __HAL_RCC_USART2_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_USART2SMEN) == RESET) #if defined(USART3) #define __HAL_RCC_USART3_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_USART3SMEN) == RESET) #endif /* USART3 */ #if defined(UART4) #define __HAL_RCC_UART4_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_UART4SMEN) == RESET) #endif /* UART4 */ #if defined(UART5) #define __HAL_RCC_UART5_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_UART5SMEN) == RESET) #endif /* UART5 */ #define __HAL_RCC_I2C1_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_I2C1SMEN) == RESET) #if defined(I2C2) #define __HAL_RCC_I2C2_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_I2C2SMEN) == RESET) #endif /* I2C2 */ #define __HAL_RCC_I2C3_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_I2C3SMEN) == RESET) #if defined(I2C4) #define __HAL_RCC_I2C4_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_I2C4SMEN) == RESET) #endif /* I2C4 */ #if defined(CRS) #define __HAL_RCC_CRS_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_CRSSMEN) == RESET) #endif /* CRS */ #define __HAL_RCC_CAN1_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_CAN1SMEN) == RESET) #if defined(USB) #define __HAL_RCC_USB_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_USBFSSMEN) == RESET) #endif /* USB */ #define __HAL_RCC_PWR_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_PWRSMEN) == RESET) #define __HAL_RCC_DAC1_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_DAC1SMEN) == RESET) #define __HAL_RCC_OPAMP_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_OPAMPSMEN) == RESET) #define __HAL_RCC_LPTIM1_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_LPTIM1SMEN) == RESET) #define __HAL_RCC_LPUART1_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_LPUART1SMEN) == RESET) #if defined(SWPMI1) #define __HAL_RCC_SWPMI1_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_SWPMI1SMEN) == RESET) #endif /* SWPMI1 */ #define __HAL_RCC_LPTIM2_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_LPTIM2SMEN) == RESET) /** * @} */ /** @defgroup RCC_APB2_Clock_Sleep_Enable_Disable_Status APB2 Peripheral Clock Sleep Enabled or Disabled Status * @brief Check whether the APB2 peripheral clock during Low Power (Sleep) mode is enabled or not. * @note Peripheral clock gating in SLEEP mode can be used to further reduce * power consumption. * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. * @note By default, all peripheral clocks are enabled during SLEEP mode. * @{ */ #define __HAL_RCC_SYSCFG_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SYSCFGSMEN) != RESET) #if defined(SDMMC1) #define __HAL_RCC_SDMMC1_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SDMMC1SMEN) != RESET) #endif /* SDMMC1 */ #define __HAL_RCC_TIM1_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM1SMEN) != RESET) #define __HAL_RCC_SPI1_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SPI1SMEN) != RESET) #if defined(TIM8) #define __HAL_RCC_TIM8_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM8SMEN) != RESET) #endif /* TIM8 */ #define __HAL_RCC_USART1_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_USART1SMEN) != RESET) #define __HAL_RCC_TIM15_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM15SMEN) != RESET) #define __HAL_RCC_TIM16_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM16SMEN) != RESET) #if defined(TIM17) #define __HAL_RCC_TIM17_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM17SMEN) != RESET) #endif /* TIM17 */ #define __HAL_RCC_SAI1_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SAI1SMEN) != RESET) #if defined(SAI2) #define __HAL_RCC_SAI2_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SAI2SMEN) != RESET) #endif /* SAI2 */ #if defined(DFSDM1_Filter0) #define __HAL_RCC_DFSDM1_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_DFSDM1SMEN) != RESET) #endif /* DFSDM1_Filter0 */ #define __HAL_RCC_SYSCFG_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SYSCFGSMEN) == RESET) #if defined(SDMMC1) #define __HAL_RCC_SDMMC1_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SDMMC1SMEN) == RESET) #endif /* SDMMC1 */ #define __HAL_RCC_TIM1_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM1SMEN) == RESET) #define __HAL_RCC_SPI1_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SPI1SMEN) == RESET) #if defined(TIM8) #define __HAL_RCC_TIM8_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM8SMEN) == RESET) #endif /* TIM8 */ #define __HAL_RCC_USART1_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_USART1SMEN) == RESET) #define __HAL_RCC_TIM15_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM15SMEN) == RESET) #define __HAL_RCC_TIM16_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM16SMEN) == RESET) #if defined(TIM17) #define __HAL_RCC_TIM17_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM17SMEN) == RESET) #endif /* TIM17 */ #define __HAL_RCC_SAI1_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SAI1SMEN) == RESET) #if defined(SAI2) #define __HAL_RCC_SAI2_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SAI2SMEN) == RESET) #endif /* SAI2 */ #if defined(DFSDM1_Filter0) #define __HAL_RCC_DFSDM1_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_DFSDM1SMEN) == RESET) #endif /* DFSDM1_Filter0 */ /** * @} */ /** @defgroup RCC_Backup_Domain_Reset RCC Backup Domain Reset * @{ */ /** @brief Macros to force or release the Backup domain reset. * @note This function resets the RTC peripheral (including the backup registers) * and the RTC clock source selection in RCC_CSR register. * @note The BKPSRAM is not affected by this reset. * @retval None */ #define __HAL_RCC_BACKUPRESET_FORCE() SET_BIT(RCC->BDCR, RCC_BDCR_BDRST) #define __HAL_RCC_BACKUPRESET_RELEASE() CLEAR_BIT(RCC->BDCR, RCC_BDCR_BDRST) /** * @} */ /** @defgroup RCC_RTC_Clock_Configuration RCC RTC Clock Configuration * @{ */ /** @brief Macros to enable or disable the RTC clock. * @note As the RTC is in the Backup domain and write access is denied to * this domain after reset, you have to enable write access using * HAL_PWR_EnableBkUpAccess() function before to configure the RTC * (to be done once after reset). * @note These macros must be used after the RTC clock source was selected. * @retval None */ #define __HAL_RCC_RTC_ENABLE() SET_BIT(RCC->BDCR, RCC_BDCR_RTCEN) #define __HAL_RCC_RTC_DISABLE() CLEAR_BIT(RCC->BDCR, RCC_BDCR_RTCEN) /** * @} */ /** @brief Macros to enable or disable the Internal High Speed 16MHz oscillator (HSI). * @note The HSI is stopped by hardware when entering STOP and STANDBY modes. * It is used (enabled by hardware) as system clock source after startup * from Reset, wakeup from STOP and STANDBY mode, or in case of failure * of the HSE used directly or indirectly as system clock (if the Clock * Security System CSS is enabled). * @note HSI can not be stopped if it is used as system clock source. In this case, * you have to select another source of the system clock then stop the HSI. * @note After enabling the HSI, the application software should wait on HSIRDY * flag to be set indicating that HSI clock is stable and can be used as * system clock source. * This parameter can be: ENABLE or DISABLE. * @note When the HSI is stopped, HSIRDY flag goes low after 6 HSI oscillator * clock cycles. * @retval None */ #define __HAL_RCC_HSI_ENABLE() SET_BIT(RCC->CR, RCC_CR_HSION) #define __HAL_RCC_HSI_DISABLE() CLEAR_BIT(RCC->CR, RCC_CR_HSION) /** @brief Macro to adjust the Internal High Speed 16MHz oscillator (HSI) calibration value. * @note The calibration is used to compensate for the variations in voltage * and temperature that influence the frequency of the internal HSI RC. * @param __HSICALIBRATIONVALUE__: specifies the calibration trimming value * (default is RCC_HSICALIBRATION_DEFAULT). * This parameter must be a number between 0 and 0x1F (STM32L43x/STM32L44x/STM32L47x/STM32L48x) or 0x7F (for other devices). * @retval None */ #define __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(__HSICALIBRATIONVALUE__) \ MODIFY_REG(RCC->ICSCR, RCC_ICSCR_HSITRIM, (uint32_t)(__HSICALIBRATIONVALUE__) << POSITION_VAL(RCC_ICSCR_HSITRIM)) /** * @brief Macros to enable or disable the wakeup the Internal High Speed oscillator (HSI) * in parallel to the Internal Multi Speed oscillator (MSI) used at system wakeup. * @note The enable of this function has not effect on the HSION bit. * This parameter can be: ENABLE or DISABLE. * @retval None */ #define __HAL_RCC_HSIAUTOMATIC_START_ENABLE() SET_BIT(RCC->CR, RCC_CR_HSIASFS) #define __HAL_RCC_HSIAUTOMATIC_START_DISABLE() CLEAR_BIT(RCC->CR, RCC_CR_HSIASFS) /** * @brief Macros to enable or disable the force of the Internal High Speed oscillator (HSI) * in STOP mode to be quickly available as kernel clock for USARTs and I2Cs. * @note Keeping the HSI ON in STOP mode allows to avoid slowing down the communication * speed because of the HSI startup time. * @note The enable of this function has not effect on the HSION bit. * This parameter can be: ENABLE or DISABLE. * @retval None */ #define __HAL_RCC_HSISTOP_ENABLE() SET_BIT(RCC->CR, RCC_CR_HSIKERON) #define __HAL_RCC_HSISTOP_DISABLE() CLEAR_BIT(RCC->CR, RCC_CR_HSIKERON) /** * @brief Macros to enable or disable the Internal Multi Speed oscillator (MSI). * @note The MSI is stopped by hardware when entering STOP and STANDBY modes. * It is used (enabled by hardware) as system clock source after * startup from Reset, wakeup from STOP and STANDBY mode, or in case * of failure of the HSE used directly or indirectly as system clock * (if the Clock Security System CSS is enabled). * @note MSI can not be stopped if it is used as system clock source. * In this case, you have to select another source of the system * clock then stop the MSI. * @note After enabling the MSI, the application software should wait on * MSIRDY flag to be set indicating that MSI clock is stable and can * be used as system clock source. * @note When the MSI is stopped, MSIRDY flag goes low after 6 MSI oscillator * clock cycles. * @retval None */ #define __HAL_RCC_MSI_ENABLE() SET_BIT(RCC->CR, RCC_CR_MSION) #define __HAL_RCC_MSI_DISABLE() CLEAR_BIT(RCC->CR, RCC_CR_MSION) /** @brief Macro Adjusts the Internal Multi Speed oscillator (MSI) calibration value. * @note The calibration is used to compensate for the variations in voltage * and temperature that influence the frequency of the internal MSI RC. * Refer to the Application Note AN3300 for more details on how to * calibrate the MSI. * @param __MSICALIBRATIONVALUE__: specifies the calibration trimming value * (default is RCC_MSICALIBRATION_DEFAULT). * This parameter must be a number between 0 and 255. * @retval None */ #define __HAL_RCC_MSI_CALIBRATIONVALUE_ADJUST(__MSICALIBRATIONVALUE__) \ MODIFY_REG(RCC->ICSCR, RCC_ICSCR_MSITRIM, (uint32_t)(__MSICALIBRATIONVALUE__) << 8) /** * @brief Macro configures the Internal Multi Speed oscillator (MSI) clock range in run mode * @note After restart from Reset , the MSI clock is around 4 MHz. * After stop the startup clock can be MSI (at any of its possible * frequencies, the one that was used before entering stop mode) or HSI. * After Standby its frequency can be selected between 4 possible values * (1, 2, 4 or 8 MHz). * @note MSIRANGE can be modified when MSI is OFF (MSION=0) or when MSI is ready * (MSIRDY=1). * @note The MSI clock range after reset can be modified on the fly. * @param __MSIRANGEVALUE__: specifies the MSI clock range. * This parameter must be one of the following values: * @arg @ref RCC_MSIRANGE_0 MSI clock is around 100 KHz * @arg @ref RCC_MSIRANGE_1 MSI clock is around 200 KHz * @arg @ref RCC_MSIRANGE_2 MSI clock is around 400 KHz * @arg @ref RCC_MSIRANGE_3 MSI clock is around 800 KHz * @arg @ref RCC_MSIRANGE_4 MSI clock is around 1 MHz * @arg @ref RCC_MSIRANGE_5 MSI clock is around 2 MHz * @arg @ref RCC_MSIRANGE_6 MSI clock is around 4 MHz (default after Reset) * @arg @ref RCC_MSIRANGE_7 MSI clock is around 8 MHz * @arg @ref RCC_MSIRANGE_8 MSI clock is around 16 MHz * @arg @ref RCC_MSIRANGE_9 MSI clock is around 24 MHz * @arg @ref RCC_MSIRANGE_10 MSI clock is around 32 MHz * @arg @ref RCC_MSIRANGE_11 MSI clock is around 48 MHz * @retval None */ #define __HAL_RCC_MSI_RANGE_CONFIG(__MSIRANGEVALUE__) \ do { \ SET_BIT(RCC->CR, RCC_CR_MSIRGSEL); \ MODIFY_REG(RCC->CR, RCC_CR_MSIRANGE, (__MSIRANGEVALUE__)); \ } while(0) /** * @brief Macro configures the Internal Multi Speed oscillator (MSI) clock range after Standby mode * After Standby its frequency can be selected between 4 possible values (1, 2, 4 or 8 MHz). * @param __MSIRANGEVALUE__: specifies the MSI clock range. * This parameter must be one of the following values: * @arg @ref RCC_MSIRANGE_4 MSI clock is around 1 MHz * @arg @ref RCC_MSIRANGE_5 MSI clock is around 2 MHz * @arg @ref RCC_MSIRANGE_6 MSI clock is around 4 MHz (default after Reset) * @arg @ref RCC_MSIRANGE_7 MSI clock is around 8 MHz * @retval None */ #define __HAL_RCC_MSI_STANDBY_RANGE_CONFIG(__MSIRANGEVALUE__) \ MODIFY_REG(RCC->CSR, RCC_CSR_MSISRANGE, (__MSIRANGEVALUE__) << 4U) /** @brief Macro to get the Internal Multi Speed oscillator (MSI) clock range in run mode * @retval MSI clock range. * This parameter must be one of the following values: * @arg @ref RCC_MSIRANGE_0 MSI clock is around 100 KHz * @arg @ref RCC_MSIRANGE_1 MSI clock is around 200 KHz * @arg @ref RCC_MSIRANGE_2 MSI clock is around 400 KHz * @arg @ref RCC_MSIRANGE_3 MSI clock is around 800 KHz * @arg @ref RCC_MSIRANGE_4 MSI clock is around 1 MHz * @arg @ref RCC_MSIRANGE_5 MSI clock is around 2 MHz * @arg @ref RCC_MSIRANGE_6 MSI clock is around 4 MHz (default after Reset) * @arg @ref RCC_MSIRANGE_7 MSI clock is around 8 MHz * @arg @ref RCC_MSIRANGE_8 MSI clock is around 16 MHz * @arg @ref RCC_MSIRANGE_9 MSI clock is around 24 MHz * @arg @ref RCC_MSIRANGE_10 MSI clock is around 32 MHz * @arg @ref RCC_MSIRANGE_11 MSI clock is around 48 MHz */ #define __HAL_RCC_GET_MSI_RANGE() \ ((READ_BIT(RCC->CR, RCC_CR_MSIRGSEL) != RESET) ? \ (uint32_t)(READ_BIT(RCC->CR, RCC_CR_MSIRANGE)) : \ (uint32_t)(READ_BIT(RCC->CSR, RCC_CSR_MSISRANGE) >> 4)) /** @brief Macros to enable or disable the Internal Low Speed oscillator (LSI). * @note After enabling the LSI, the application software should wait on * LSIRDY flag to be set indicating that LSI clock is stable and can * be used to clock the IWDG and/or the RTC. * @note LSI can not be disabled if the IWDG is running. * @note When the LSI is stopped, LSIRDY flag goes low after 6 LSI oscillator * clock cycles. * @retval None */ #define __HAL_RCC_LSI_ENABLE() SET_BIT(RCC->CSR, RCC_CSR_LSION) #define __HAL_RCC_LSI_DISABLE() CLEAR_BIT(RCC->CSR, RCC_CSR_LSION) /** * @brief Macro to configure the External High Speed oscillator (HSE). * @note Transition HSE Bypass to HSE On and HSE On to HSE Bypass are not * supported by this macro. User should request a transition to HSE Off * first and then HSE On or HSE Bypass. * @note After enabling the HSE (RCC_HSE_ON or RCC_HSE_Bypass), the application * software should wait on HSERDY flag to be set indicating that HSE clock * is stable and can be used to clock the PLL and/or system clock. * @note HSE state can not be changed if it is used directly or through the * PLL as system clock. In this case, you have to select another source * of the system clock then change the HSE state (ex. disable it). * @note The HSE is stopped by hardware when entering STOP and STANDBY modes. * @note This function reset the CSSON bit, so if the clock security system(CSS) * was previously enabled you have to enable it again after calling this * function. * @param __STATE__: specifies the new state of the HSE. * This parameter can be one of the following values: * @arg @ref RCC_HSE_OFF Turn OFF the HSE oscillator, HSERDY flag goes low after * 6 HSE oscillator clock cycles. * @arg @ref RCC_HSE_ON Turn ON the HSE oscillator. * @arg @ref RCC_HSE_BYPASS HSE oscillator bypassed with external clock. * @retval None */ #define __HAL_RCC_HSE_CONFIG(__STATE__) \ do { \ if((__STATE__) == RCC_HSE_ON) \ { \ SET_BIT(RCC->CR, RCC_CR_HSEON); \ } \ else if((__STATE__) == RCC_HSE_BYPASS) \ { \ SET_BIT(RCC->CR, RCC_CR_HSEBYP); \ SET_BIT(RCC->CR, RCC_CR_HSEON); \ } \ else \ { \ CLEAR_BIT(RCC->CR, RCC_CR_HSEON); \ CLEAR_BIT(RCC->CR, RCC_CR_HSEBYP); \ } \ } while(0) /** * @brief Macro to configure the External Low Speed oscillator (LSE). * @note Transitions LSE Bypass to LSE On and LSE On to LSE Bypass are not * supported by this macro. User should request a transition to LSE Off * first and then LSE On or LSE Bypass. * @note As the LSE is in the Backup domain and write access is denied to * this domain after reset, you have to enable write access using * HAL_PWR_EnableBkUpAccess() function before to configure the LSE * (to be done once after reset). * @note After enabling the LSE (RCC_LSE_ON or RCC_LSE_BYPASS), the application * software should wait on LSERDY flag to be set indicating that LSE clock * is stable and can be used to clock the RTC. * @param __STATE__: specifies the new state of the LSE. * This parameter can be one of the following values: * @arg @ref RCC_LSE_OFF Turn OFF the LSE oscillator, LSERDY flag goes low after * 6 LSE oscillator clock cycles. * @arg @ref RCC_LSE_ON Turn ON the LSE oscillator. * @arg @ref RCC_LSE_BYPASS LSE oscillator bypassed with external clock. * @retval None */ #define __HAL_RCC_LSE_CONFIG(__STATE__) \ do { \ if((__STATE__) == RCC_LSE_ON) \ { \ SET_BIT(RCC->BDCR, RCC_BDCR_LSEON); \ } \ else if((__STATE__) == RCC_LSE_BYPASS) \ { \ SET_BIT(RCC->BDCR, RCC_BDCR_LSEBYP); \ SET_BIT(RCC->BDCR, RCC_BDCR_LSEON); \ } \ else \ { \ CLEAR_BIT(RCC->BDCR, RCC_BDCR_LSEON); \ CLEAR_BIT(RCC->BDCR, RCC_BDCR_LSEBYP); \ } \ } while(0) #if defined(RCC_HSI48_SUPPORT) /** @brief Macros to enable or disable the Internal High Speed 48MHz oscillator (HSI48). * @note The HSI48 is stopped by hardware when entering STOP and STANDBY modes. * @note After enabling the HSI48, the application software should wait on HSI48RDY * flag to be set indicating that HSI48 clock is stable. * This parameter can be: ENABLE or DISABLE. * @retval None */ #define __HAL_RCC_HSI48_ENABLE() SET_BIT(RCC->CRRCR, RCC_CRRCR_HSI48ON) #define __HAL_RCC_HSI48_DISABLE() CLEAR_BIT(RCC->CRRCR, RCC_CRRCR_HSI48ON) #endif /* RCC_HSI48_SUPPORT */ /** @brief Macros to configure the RTC clock (RTCCLK). * @note As the RTC clock configuration bits are in the Backup domain and write * access is denied to this domain after reset, you have to enable write * access using the Power Backup Access macro before to configure * the RTC clock source (to be done once after reset). * @note Once the RTC clock is configured it cannot be changed unless the * Backup domain is reset using __HAL_RCC_BACKUPRESET_FORCE() macro, or by * a Power On Reset (POR). * * @param __RTC_CLKSOURCE__: specifies the RTC clock source. * This parameter can be one of the following values: * @arg @ref RCC_RTCCLKSOURCE_NO_CLK No clock selected as RTC clock. * @arg @ref RCC_RTCCLKSOURCE_LSE LSE selected as RTC clock. * @arg @ref RCC_RTCCLKSOURCE_LSI LSI selected as RTC clock. * @arg @ref RCC_RTCCLKSOURCE_HSE_DIV32 HSE clock divided by 32 selected * * @note If the LSE or LSI is used as RTC clock source, the RTC continues to * work in STOP and STANDBY modes, and can be used as wakeup source. * However, when the HSE clock is used as RTC clock source, the RTC * cannot be used in STOP and STANDBY modes. * @note The maximum input clock frequency for RTC is 1MHz (when using HSE as * RTC clock source). * @retval None */ #define __HAL_RCC_RTC_CONFIG(__RTC_CLKSOURCE__) \ MODIFY_REG( RCC->BDCR, RCC_BDCR_RTCSEL, (__RTC_CLKSOURCE__)) /** @brief Macro to get the RTC clock source. * @retval The returned value can be one of the following: * @arg @ref RCC_RTCCLKSOURCE_NO_CLK No clock selected as RTC clock. * @arg @ref RCC_RTCCLKSOURCE_LSE LSE selected as RTC clock. * @arg @ref RCC_RTCCLKSOURCE_LSI LSI selected as RTC clock. * @arg @ref RCC_RTCCLKSOURCE_HSE_DIV32 HSE clock divided by 32 selected */ #define __HAL_RCC_GET_RTC_SOURCE() ((uint32_t)(READ_BIT(RCC->BDCR, RCC_BDCR_RTCSEL))) /** @brief Macros to enable or disable the main PLL. * @note After enabling the main PLL, the application software should wait on * PLLRDY flag to be set indicating that PLL clock is stable and can * be used as system clock source. * @note The main PLL can not be disabled if it is used as system clock source * @note The main PLL is disabled by hardware when entering STOP and STANDBY modes. * @retval None */ #define __HAL_RCC_PLL_ENABLE() SET_BIT(RCC->CR, RCC_CR_PLLON) #define __HAL_RCC_PLL_DISABLE() CLEAR_BIT(RCC->CR, RCC_CR_PLLON) /** @brief Macro to configure the PLL clock source. * @note This function must be used only when the main PLL is disabled. * @param __PLLSOURCE__: specifies the PLL entry clock source. * This parameter can be one of the following values: * @arg @ref RCC_PLLSOURCE_NONE No clock selected as PLL clock entry * @arg @ref RCC_PLLSOURCE_MSI MSI oscillator clock selected as PLL clock entry * @arg @ref RCC_PLLSOURCE_HSI HSI oscillator clock selected as PLL clock entry * @arg @ref RCC_PLLSOURCE_HSE HSE oscillator clock selected as PLL clock entry * @note This clock source is common for the main PLL and audio PLL (PLLSAI1 and PLLSAI2). * @retval None * */ #define __HAL_RCC_PLL_PLLSOURCE_CONFIG(__PLLSOURCE__) \ MODIFY_REG(RCC->PLLCFGR, RCC_PLLCFGR_PLLSRC, (__PLLSOURCE__)) /** @brief Macro to configure the PLL source division factor M. * @note This function must be used only when the main PLL is disabled. * @param __PLLM__: specifies the division factor for PLL VCO input clock * This parameter must be a number between Min_Data = 1 and Max_Data = 8. * @note You have to set the PLLM parameter correctly to ensure that the VCO input * frequency ranges from 4 to 16 MHz. It is recommended to select a frequency * of 16 MHz to limit PLL jitter. * @retval None * */ #define __HAL_RCC_PLL_PLLM_CONFIG(__PLLM__) \ MODIFY_REG(RCC->PLLCFGR, RCC_PLLCFGR_PLLM, ((__PLLM__) - 1) << 4U) /** * @brief Macro to configure the main PLL clock source, multiplication and division factors. * @note This function must be used only when the main PLL is disabled. * * @param __PLLSOURCE__: specifies the PLL entry clock source. * This parameter can be one of the following values: * @arg @ref RCC_PLLSOURCE_NONE No clock selected as PLL clock entry * @arg @ref RCC_PLLSOURCE_MSI MSI oscillator clock selected as PLL clock entry * @arg @ref RCC_PLLSOURCE_HSI HSI oscillator clock selected as PLL clock entry * @arg @ref RCC_PLLSOURCE_HSE HSE oscillator clock selected as PLL clock entry * @note This clock source is common for the main PLL and audio PLL (PLLSAI1 and PLLSAI2). * * @param __PLLM__: specifies the division factor for PLL VCO input clock. * This parameter must be a number between 1 and 8. * @note You have to set the PLLM parameter correctly to ensure that the VCO input * frequency ranges from 4 to 16 MHz. It is recommended to select a frequency * of 16 MHz to limit PLL jitter. * * @param __PLLN__: specifies the multiplication factor for PLL VCO output clock. * This parameter must be a number between 8 and 86. * @note You have to set the PLLN parameter correctly to ensure that the VCO * output frequency is between 64 and 344 MHz. * * @param __PLLP__: specifies the division factor for SAI clock. * This parameter must be a number in the range (7 or 17) for STM32L47x/STM32L48x * else (2 to 31). * * @param __PLLQ__: specifies the division factor for OTG FS, SDMMC1 and RNG clocks. * This parameter must be in the range (2, 4, 6 or 8). * @note If the USB OTG FS is used in your application, you have to set the * PLLQ parameter correctly to have 48 MHz clock for the USB. However, * the SDMMC1 and RNG need a frequency lower than or equal to 48 MHz to work * correctly. * @param __PLLR__: specifies the division factor for the main system clock. * @note You have to set the PLLR parameter correctly to not exceed 80MHZ. * This parameter must be in the range (2, 4, 6 or 8). * @retval None */ #if defined(RCC_PLLP_DIV_2_31_SUPPORT) #define __HAL_RCC_PLL_CONFIG(__PLLSOURCE__, __PLLM__, __PLLN__, __PLLP__, __PLLQ__,__PLLR__ ) \ (RCC->PLLCFGR = (uint32_t)(((__PLLM__) - 1U) << 4U) | (uint32_t)((__PLLN__) << 8U) | \ (uint32_t)(__PLLSOURCE__) | (uint32_t)((((__PLLQ__) >> 1U) - 1U) << 21U) | (uint32_t)((((__PLLR__) >> 1U) - 1U) << 25U) | \ (uint32_t)((__PLLP__) << 27U)) #else #define __HAL_RCC_PLL_CONFIG(__PLLSOURCE__, __PLLM__, __PLLN__, __PLLP__, __PLLQ__,__PLLR__ ) \ (RCC->PLLCFGR = (uint32_t)(((__PLLM__) - 1U) << 4U) | (uint32_t)((__PLLN__) << 8U) | (uint32_t)(((__PLLP__) >> 4U ) << 17U) | \ (uint32_t)(__PLLSOURCE__) | (uint32_t)((((__PLLQ__) >> 1U) - 1U) << 21U) | (uint32_t)((((__PLLR__) >> 1U) - 1U) << 25U)) #endif /* RCC_PLLP_DIV_2_31_SUPPORT */ /** @brief Macro to get the oscillator used as PLL clock source. * @retval The oscillator used as PLL clock source. The returned value can be one * of the following: * - RCC_PLLSOURCE_NONE: No oscillator is used as PLL clock source. * - RCC_PLLSOURCE_MSI: MSI oscillator is used as PLL clock source. * - RCC_PLLSOURCE_HSI: HSI oscillator is used as PLL clock source. * - RCC_PLLSOURCE_HSE: HSE oscillator is used as PLL clock source. */ #define __HAL_RCC_GET_PLL_OSCSOURCE() ((uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC)) /** * @brief Enable or disable each clock output (RCC_PLL_SYSCLK, RCC_PLL_48M1CLK, RCC_PLL_SAI3CLK) * @note Enabling/disabling clock outputs RCC_PLL_SAI3CLK and RCC_PLL_48M1CLK can be done at anytime * without the need to stop the PLL in order to save power. But RCC_PLL_SYSCLK cannot * be stopped if used as System Clock. * @param __PLLCLOCKOUT__: specifies the PLL clock to be output. * This parameter can be one or a combination of the following values: * @arg @ref RCC_PLL_SAI3CLK This clock is used to generate an accurate clock to achieve * high-quality audio performance on SAI interface in case. * @arg @ref RCC_PLL_48M1CLK This Clock is used to generate the clock for the USB OTG FS (48 MHz), * the random analog generator (<=48 MHz) and the SDMMC1 (<= 48 MHz). * @arg @ref RCC_PLL_SYSCLK This Clock is used to generate the high speed system clock (up to 80MHz) * @retval None */ #define __HAL_RCC_PLLCLKOUT_ENABLE(__PLLCLOCKOUT__) SET_BIT(RCC->PLLCFGR, (__PLLCLOCKOUT__)) #define __HAL_RCC_PLLCLKOUT_DISABLE(__PLLCLOCKOUT__) CLEAR_BIT(RCC->PLLCFGR, (__PLLCLOCKOUT__)) /** * @brief Get clock output enable status (RCC_PLL_SYSCLK, RCC_PLL_48M1CLK, RCC_PLL_SAI3CLK) * @param __PLLCLOCKOUT__: specifies the output PLL clock to be checked. * This parameter can be one of the following values: * @arg @ref RCC_PLL_SAI3CLK This clock is used to generate an accurate clock to achieve * high-quality audio performance on SAI interface in case. * @arg @ref RCC_PLL_48M1CLK This Clock is used to generate the clock for the USB OTG FS (48 MHz), * the random analog generator (<=48 MHz) and the SDMMC1 (<= 48 MHz). * @arg @ref RCC_PLL_SYSCLK This Clock is used to generate the high speed system clock (up to 80MHz) * @retval SET / RESET */ #define __HAL_RCC_GET_PLLCLKOUT_CONFIG(__PLLCLOCKOUT__) READ_BIT(RCC->PLLCFGR, (__PLLCLOCKOUT__)) /** * @brief Macro to configure the system clock source. * @param __SYSCLKSOURCE__: specifies the system clock source. * This parameter can be one of the following values: * - RCC_SYSCLKSOURCE_MSI: MSI oscillator is used as system clock source. * - RCC_SYSCLKSOURCE_HSI: HSI oscillator is used as system clock source. * - RCC_SYSCLKSOURCE_HSE: HSE oscillator is used as system clock source. * - RCC_SYSCLKSOURCE_PLLCLK: PLL output is used as system clock source. * @retval None */ #define __HAL_RCC_SYSCLK_CONFIG(__SYSCLKSOURCE__) \ MODIFY_REG(RCC->CFGR, RCC_CFGR_SW, (__SYSCLKSOURCE__)) /** @brief Macro to get the clock source used as system clock. * @retval The clock source used as system clock. The returned value can be one * of the following: * - RCC_SYSCLKSOURCE_STATUS_MSI: MSI used as system clock. * - RCC_SYSCLKSOURCE_STATUS_HSI: HSI used as system clock. * - RCC_SYSCLKSOURCE_STATUS_HSE: HSE used as system clock. * - RCC_SYSCLKSOURCE_STATUS_PLLCLK: PLL used as system clock. */ #define __HAL_RCC_GET_SYSCLK_SOURCE() ((uint32_t)(RCC->CFGR & RCC_CFGR_SWS)) /** * @brief Macro to configure the External Low Speed oscillator (LSE) drive capability. * @note As the LSE is in the Backup domain and write access is denied to * this domain after reset, you have to enable write access using * HAL_PWR_EnableBkUpAccess() function before to configure the LSE * (to be done once after reset). * @param __LSEDRIVE__: specifies the new state of the LSE drive capability. * This parameter can be one of the following values: * @arg @ref RCC_LSEDRIVE_LOW LSE oscillator low drive capability. * @arg @ref RCC_LSEDRIVE_MEDIUMLOW LSE oscillator medium low drive capability. * @arg @ref RCC_LSEDRIVE_MEDIUMHIGH LSE oscillator medium high drive capability. * @arg @ref RCC_LSEDRIVE_HIGH LSE oscillator high drive capability. * @retval None */ #define __HAL_RCC_LSEDRIVE_CONFIG(__LSEDRIVE__) \ MODIFY_REG(RCC->BDCR, RCC_BDCR_LSEDRV, (uint32_t)(__LSEDRIVE__)) /** * @brief Macro to configure the wake up from stop clock. * @param __STOPWUCLK__: specifies the clock source used after wake up from stop. * This parameter can be one of the following values: * @arg @ref RCC_STOP_WAKEUPCLOCK_MSI MSI selected as system clock source * @arg @ref RCC_STOP_WAKEUPCLOCK_HSI HSI selected as system clock source * @retval None */ #define __HAL_RCC_WAKEUPSTOP_CLK_CONFIG(__STOPWUCLK__) \ MODIFY_REG(RCC->CFGR, RCC_CFGR_STOPWUCK, (__STOPWUCLK__)) /** @brief Macro to configure the MCO clock. * @param __MCOCLKSOURCE__ specifies the MCO clock source. * This parameter can be one of the following values: * @arg @ref RCC_MCO1SOURCE_NOCLOCK MCO output disabled * @arg @ref RCC_MCO1SOURCE_SYSCLK System clock selected as MCO source * @arg @ref RCC_MCO1SOURCE_MSI MSI clock selected as MCO source * @arg @ref RCC_MCO1SOURCE_HSI HSI clock selected as MCO source * @arg @ref RCC_MCO1SOURCE_HSE HSE clock selected as MCO sourcee * @arg @ref RCC_MCO1SOURCE_PLLCLK Main PLL clock selected as MCO source * @arg @ref RCC_MCO1SOURCE_LSI LSI clock selected as MCO source * @arg @ref RCC_MCO1SOURCE_LSE LSE clock selected as MCO source @if STM32L443xx * @arg @ref RCC_MCO1SOURCE_HSI48 HSI48 clock selected as MCO source for devices with HSI48 @endif @if STM32L462xx * @arg @ref RCC_MCO1SOURCE_HSI48 HSI48 clock selected as MCO source for devices with HSI48 @endif * @param __MCODIV__ specifies the MCO clock prescaler. * This parameter can be one of the following values: * @arg @ref RCC_MCODIV_1 MCO clock source is divided by 1 * @arg @ref RCC_MCODIV_2 MCO clock source is divided by 2 * @arg @ref RCC_MCODIV_4 MCO clock source is divided by 4 * @arg @ref RCC_MCODIV_8 MCO clock source is divided by 8 * @arg @ref RCC_MCODIV_16 MCO clock source is divided by 16 */ #define __HAL_RCC_MCO1_CONFIG(__MCOCLKSOURCE__, __MCODIV__) \ MODIFY_REG(RCC->CFGR, (RCC_CFGR_MCOSEL | RCC_CFGR_MCOPRE), ((__MCOCLKSOURCE__) | (__MCODIV__))) /** @defgroup RCC_Flags_Interrupts_Management Flags Interrupts Management * @brief macros to manage the specified RCC Flags and interrupts. * @{ */ /** @brief Enable RCC interrupt (Perform Byte access to RCC_CIR[14:8] bits to enable * the selected interrupts). * @param __INTERRUPT__: specifies the RCC interrupt sources to be enabled. * This parameter can be any combination of the following values: * @arg @ref RCC_IT_LSIRDY LSI ready interrupt * @arg @ref RCC_IT_LSERDY LSE ready interrupt * @arg @ref RCC_IT_MSIRDY HSI ready interrupt * @arg @ref RCC_IT_HSIRDY HSI ready interrupt * @arg @ref RCC_IT_HSERDY HSE ready interrupt * @arg @ref RCC_IT_PLLRDY Main PLL ready interrupt * @arg @ref RCC_IT_PLLSAI1RDY PLLSAI1 ready interrupt * @arg @ref RCC_IT_PLLSAI2RDY PLLSAI2 ready interrupt for devices with PLLSAI2 * @arg @ref RCC_IT_LSECSS LSE Clock security system interrupt @if STM32L443xx * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt for devices with HSI48 @endif @if STM32L462xx * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt for devices with HSI48 @endif * @retval None */ #define __HAL_RCC_ENABLE_IT(__INTERRUPT__) SET_BIT(RCC->CIER, (__INTERRUPT__)) /** @brief Disable RCC interrupt (Perform Byte access to RCC_CIR[14:8] bits to disable * the selected interrupts). * @param __INTERRUPT__: specifies the RCC interrupt sources to be disabled. * This parameter can be any combination of the following values: * @arg @ref RCC_IT_LSIRDY LSI ready interrupt * @arg @ref RCC_IT_LSERDY LSE ready interrupt * @arg @ref RCC_IT_MSIRDY HSI ready interrupt * @arg @ref RCC_IT_HSIRDY HSI ready interrupt * @arg @ref RCC_IT_HSERDY HSE ready interrupt * @arg @ref RCC_IT_PLLRDY Main PLL ready interrupt * @arg @ref RCC_IT_PLLSAI1RDY PLLSAI1 ready interrupt * @arg @ref RCC_IT_PLLSAI2RDY PLLSAI2 ready interrupt for devices with PLLSAI2 * @arg @ref RCC_IT_LSECSS LSE Clock security system interrupt @if STM32L443xx * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt for devices with HSI48 @endif @if STM32L462xx * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt for devices with HSI48 @endif * @retval None */ #define __HAL_RCC_DISABLE_IT(__INTERRUPT__) CLEAR_BIT(RCC->CIER, (__INTERRUPT__)) /** @brief Clear the RCC's interrupt pending bits (Perform Byte access to RCC_CIR[23:16] * bits to clear the selected interrupt pending bits. * @param __INTERRUPT__: specifies the interrupt pending bit to clear. * This parameter can be any combination of the following values: * @arg @ref RCC_IT_LSIRDY LSI ready interrupt * @arg @ref RCC_IT_LSERDY LSE ready interrupt * @arg @ref RCC_IT_MSIRDY MSI ready interrupt * @arg @ref RCC_IT_HSIRDY HSI ready interrupt * @arg @ref RCC_IT_HSERDY HSE ready interrupt * @arg @ref RCC_IT_PLLRDY Main PLL ready interrupt * @arg @ref RCC_IT_PLLSAI1RDY PLLSAI1 ready interrupt * @arg @ref RCC_IT_PLLSAI2RDY PLLSAI2 ready interrupt for devices with PLLSAI2 * @arg @ref RCC_IT_CSS HSE Clock security system interrupt * @arg @ref RCC_IT_LSECSS LSE Clock security system interrupt @if STM32L443xx * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt for devices with HSI48 @endif @if STM32L462xx * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt for devices with HSI48 @endif * @retval None */ #define __HAL_RCC_CLEAR_IT(__INTERRUPT__) (RCC->CICR = (__INTERRUPT__)) /** @brief Check whether the RCC interrupt has occurred or not. * @param __INTERRUPT__: specifies the RCC interrupt source to check. * This parameter can be one of the following values: * @arg @ref RCC_IT_LSIRDY LSI ready interrupt * @arg @ref RCC_IT_LSERDY LSE ready interrupt * @arg @ref RCC_IT_MSIRDY MSI ready interrupt * @arg @ref RCC_IT_HSIRDY HSI ready interrupt * @arg @ref RCC_IT_HSERDY HSE ready interrupt * @arg @ref RCC_IT_PLLRDY Main PLL ready interrupt * @arg @ref RCC_IT_PLLSAI1RDY PLLSAI1 ready interrupt * @arg @ref RCC_IT_PLLSAI2RDY PLLSAI2 ready interrupt for devices with PLLSAI2 * @arg @ref RCC_IT_CSS HSE Clock security system interrupt * @arg @ref RCC_IT_LSECSS LSE Clock security system interrupt @if STM32L443xx * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt for devices with HSI48 @endif @if STM32L462xx * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt for devices with HSI48 @endif * @retval The new state of __INTERRUPT__ (TRUE or FALSE). */ #define __HAL_RCC_GET_IT(__INTERRUPT__) ((RCC->CIFR & (__INTERRUPT__)) == (__INTERRUPT__)) /** @brief Set RMVF bit to clear the reset flags. * The reset flags are: RCC_FLAG_FWRRST, RCC_FLAG_OBLRST, RCC_FLAG_PINRST, RCC_FLAG_BORRST, * RCC_FLAG_SFTRST, RCC_FLAG_IWDGRST, RCC_FLAG_WWDGRST and RCC_FLAG_LPWRRST. * @retval None */ #define __HAL_RCC_CLEAR_RESET_FLAGS() (RCC->CSR |= RCC_CSR_RMVF) /** @brief Check whether the selected RCC flag is set or not. * @param __FLAG__: specifies the flag to check. * This parameter can be one of the following values: * @arg @ref RCC_FLAG_MSIRDY MSI oscillator clock ready * @arg @ref RCC_FLAG_HSIRDY HSI oscillator clock ready * @arg @ref RCC_FLAG_HSERDY HSE oscillator clock ready * @arg @ref RCC_FLAG_PLLRDY Main PLL clock ready * @arg @ref RCC_FLAG_PLLSAI1RDY PLLSAI1 clock ready * @arg @ref RCC_FLAG_PLLSAI2RDY PLLSAI2 clock ready for devices with PLLSAI2 @if STM32L443xx * @arg @ref RCC_FLAG_HSI48RDY HSI48 clock ready for devices with HSI48 @endif @if STM32L462xx * @arg @ref RCC_FLAG_HSI48RDY HSI48 clock ready for devices with HSI48 @endif * @arg @ref RCC_FLAG_LSERDY LSE oscillator clock ready * @arg @ref RCC_FLAG_LSECSSD Clock security system failure on LSE oscillator detection * @arg @ref RCC_FLAG_LSIRDY LSI oscillator clock ready * @arg @ref RCC_FLAG_BORRST BOR reset * @arg @ref RCC_FLAG_OBLRST OBLRST reset * @arg @ref RCC_FLAG_PINRST Pin reset * @arg @ref RCC_FLAG_FWRST FIREWALL reset * @arg @ref RCC_FLAG_RMVF Remove reset Flag * @arg @ref RCC_FLAG_SFTRST Software reset * @arg @ref RCC_FLAG_IWDGRST Independent Watchdog reset * @arg @ref RCC_FLAG_WWDGRST Window Watchdog reset * @arg @ref RCC_FLAG_LPWRRST Low Power reset * @retval The new state of __FLAG__ (TRUE or FALSE). */ #if defined(RCC_HSI48_SUPPORT) #define __HAL_RCC_GET_FLAG(__FLAG__) (((((((__FLAG__) >> 5U) == 1U) ? RCC->CR : \ ((((__FLAG__) >> 5U) == 4U) ? RCC->CRRCR : \ ((((__FLAG__) >> 5U) == 2U) ? RCC->BDCR : \ ((((__FLAG__) >> 5U) == 3U) ? RCC->CSR : RCC->CIFR)))) & \ ((uint32_t)1U << ((__FLAG__) & RCC_FLAG_MASK))) != RESET) \ ? 1U : 0U) #else #define __HAL_RCC_GET_FLAG(__FLAG__) (((((((__FLAG__) >> 5U) == 1U) ? RCC->CR : \ ((((__FLAG__) >> 5U) == 2U) ? RCC->BDCR : \ ((((__FLAG__) >> 5U) == 3U) ? RCC->CSR : RCC->CIFR))) & \ ((uint32_t)1 << ((__FLAG__) & RCC_FLAG_MASK))) != RESET) \ ? 1U : 0U) #endif /* RCC_HSI48_SUPPORT */ /** * @} */ /** * @} */ /* Private constants ---------------------------------------------------------*/ /** @defgroup RCC_Private_Constants RCC Private Constants * @{ */ /* Defines used for Flags */ #define CR_REG_INDEX ((uint32_t)1U) #define BDCR_REG_INDEX ((uint32_t)2U) #define CSR_REG_INDEX ((uint32_t)3U) #if defined(RCC_HSI48_SUPPORT) #define CRRCR_REG_INDEX ((uint32_t)4U) #endif /* RCC_HSI48_SUPPORT */ #define RCC_FLAG_MASK ((uint32_t)0x1FU) /** * @} */ /* Private macros ------------------------------------------------------------*/ /** @addtogroup RCC_Private_Macros * @{ */ #if defined(RCC_HSI48_SUPPORT) #define IS_RCC_OSCILLATORTYPE(__OSCILLATOR__) (((__OSCILLATOR__) == RCC_OSCILLATORTYPE_NONE) || \ (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_HSE) == RCC_OSCILLATORTYPE_HSE) || \ (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_HSI) == RCC_OSCILLATORTYPE_HSI) || \ (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_HSI48) == RCC_OSCILLATORTYPE_HSI48) || \ (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_MSI) == RCC_OSCILLATORTYPE_MSI) || \ (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_LSI) == RCC_OSCILLATORTYPE_LSI) || \ (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_LSE) == RCC_OSCILLATORTYPE_LSE)) #else #define IS_RCC_OSCILLATORTYPE(__OSCILLATOR__) (((__OSCILLATOR__) == RCC_OSCILLATORTYPE_NONE) || \ (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_HSE) == RCC_OSCILLATORTYPE_HSE) || \ (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_HSI) == RCC_OSCILLATORTYPE_HSI) || \ (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_MSI) == RCC_OSCILLATORTYPE_MSI) || \ (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_LSI) == RCC_OSCILLATORTYPE_LSI) || \ (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_LSE) == RCC_OSCILLATORTYPE_LSE)) #endif /* RCC_HSI48_SUPPORT */ #define IS_RCC_HSE(__HSE__) (((__HSE__) == RCC_HSE_OFF) || ((__HSE__) == RCC_HSE_ON) || \ ((__HSE__) == RCC_HSE_BYPASS)) #define IS_RCC_LSE(__LSE__) (((__LSE__) == RCC_LSE_OFF) || ((__LSE__) == RCC_LSE_ON) || \ ((__LSE__) == RCC_LSE_BYPASS)) #define IS_RCC_HSI(__HSI__) (((__HSI__) == RCC_HSI_OFF) || ((__HSI__) == RCC_HSI_ON)) #define IS_RCC_HSI_CALIBRATION_VALUE(__VALUE__) ((__VALUE__) <= (RCC_ICSCR_HSITRIM >> POSITION_VAL(RCC_ICSCR_HSITRIM))) #define IS_RCC_LSI(__LSI__) (((__LSI__) == RCC_LSI_OFF) || ((__LSI__) == RCC_LSI_ON)) #define IS_RCC_MSI(__MSI__) (((__MSI__) == RCC_MSI_OFF) || ((__MSI__) == RCC_MSI_ON)) #define IS_RCC_MSICALIBRATION_VALUE(__VALUE__) ((__VALUE__) <= (uint32_t)255U) #if defined(RCC_HSI48_SUPPORT) #define IS_RCC_HSI48(__HSI48__) (((__HSI48__) == RCC_HSI48_OFF) || ((__HSI48__) == RCC_HSI48_ON)) #endif /* RCC_HSI48_SUPPORT */ #define IS_RCC_PLL(__PLL__) (((__PLL__) == RCC_PLL_NONE) ||((__PLL__) == RCC_PLL_OFF) || \ ((__PLL__) == RCC_PLL_ON)) #define IS_RCC_PLLSOURCE(__SOURCE__) (((__SOURCE__) == RCC_PLLSOURCE_NONE) || \ ((__SOURCE__) == RCC_PLLSOURCE_MSI) || \ ((__SOURCE__) == RCC_PLLSOURCE_HSI) || \ ((__SOURCE__) == RCC_PLLSOURCE_HSE)) #define IS_RCC_PLLM_VALUE(__VALUE__) ((1U <= (__VALUE__)) && ((__VALUE__) <= 8U)) #define IS_RCC_PLLN_VALUE(__VALUE__) ((8U <= (__VALUE__)) && ((__VALUE__) <= 86U)) #if defined(RCC_PLLP_DIV_2_31_SUPPORT) #define IS_RCC_PLLP_VALUE(__VALUE__) (((__VALUE__) >= 2U) && ((__VALUE__) <= 31U)) #else #define IS_RCC_PLLP_VALUE(__VALUE__) (((__VALUE__) == 7U) || ((__VALUE__) == 17U)) #endif /*RCC_PLLP_DIV_2_31_SUPPORT */ #define IS_RCC_PLLQ_VALUE(__VALUE__) (((__VALUE__) == 2U) || ((__VALUE__) == 4U) || \ ((__VALUE__) == 6U) || ((__VALUE__) == 8U)) #define IS_RCC_PLLR_VALUE(__VALUE__) (((__VALUE__) == 2U) || ((__VALUE__) == 4U) || \ ((__VALUE__) == 6U) || ((__VALUE__) == 8U)) #define IS_RCC_PLLSAI1CLOCKOUT_VALUE(__VALUE__) (((((__VALUE__) & RCC_PLLSAI1_SAI1CLK) == RCC_PLLSAI1_SAI1CLK) || \ (((__VALUE__) & RCC_PLLSAI1_48M2CLK) == RCC_PLLSAI1_48M2CLK) || \ (((__VALUE__) & RCC_PLLSAI1_ADC1CLK) == RCC_PLLSAI1_ADC1CLK)) && \ (((__VALUE__) & ~(RCC_PLLSAI1_SAI1CLK|RCC_PLLSAI1_48M2CLK|RCC_PLLSAI1_ADC1CLK)) == 0U)) #if defined(RCC_PLLSAI2_SUPPORT) #define IS_RCC_PLLSAI2CLOCKOUT_VALUE(__VALUE__) (((((__VALUE__) & RCC_PLLSAI2_SAI2CLK) == RCC_PLLSAI2_SAI2CLK) || \ (((__VALUE__) & RCC_PLLSAI2_ADC2CLK) == RCC_PLLSAI2_ADC2CLK)) && \ (((__VALUE__) & ~(RCC_PLLSAI2_SAI2CLK|RCC_PLLSAI2_ADC2CLK)) == 0U)) #endif /* RCC_PLLSAI2_SUPPORT */ #define IS_RCC_MSI_CLOCK_RANGE(__RANGE__) (((__RANGE__) == RCC_MSIRANGE_0) || \ ((__RANGE__) == RCC_MSIRANGE_1) || \ ((__RANGE__) == RCC_MSIRANGE_2) || \ ((__RANGE__) == RCC_MSIRANGE_3) || \ ((__RANGE__) == RCC_MSIRANGE_4) || \ ((__RANGE__) == RCC_MSIRANGE_5) || \ ((__RANGE__) == RCC_MSIRANGE_6) || \ ((__RANGE__) == RCC_MSIRANGE_7) || \ ((__RANGE__) == RCC_MSIRANGE_8) || \ ((__RANGE__) == RCC_MSIRANGE_9) || \ ((__RANGE__) == RCC_MSIRANGE_10) || \ ((__RANGE__) == RCC_MSIRANGE_11)) #define IS_RCC_MSI_STANDBY_CLOCK_RANGE(__RANGE__) (((__RANGE__) == RCC_MSIRANGE_4) || \ ((__RANGE__) == RCC_MSIRANGE_5) || \ ((__RANGE__) == RCC_MSIRANGE_6) || \ ((__RANGE__) == RCC_MSIRANGE_7)) #define IS_RCC_CLOCKTYPE(__CLK__) ((1U <= (__CLK__)) && ((__CLK__) <= 15U)) #define IS_RCC_SYSCLKSOURCE(__SOURCE__) (((__SOURCE__) == RCC_SYSCLKSOURCE_MSI) || \ ((__SOURCE__) == RCC_SYSCLKSOURCE_HSI) || \ ((__SOURCE__) == RCC_SYSCLKSOURCE_HSE) || \ ((__SOURCE__) == RCC_SYSCLKSOURCE_PLLCLK)) #define IS_RCC_HCLK(__HCLK__) (((__HCLK__) == RCC_SYSCLK_DIV1) || ((__HCLK__) == RCC_SYSCLK_DIV2) || \ ((__HCLK__) == RCC_SYSCLK_DIV4) || ((__HCLK__) == RCC_SYSCLK_DIV8) || \ ((__HCLK__) == RCC_SYSCLK_DIV16) || ((__HCLK__) == RCC_SYSCLK_DIV64) || \ ((__HCLK__) == RCC_SYSCLK_DIV128) || ((__HCLK__) == RCC_SYSCLK_DIV256) || \ ((__HCLK__) == RCC_SYSCLK_DIV512)) #define IS_RCC_PCLK(__PCLK__) (((__PCLK__) == RCC_HCLK_DIV1) || ((__PCLK__) == RCC_HCLK_DIV2) || \ ((__PCLK__) == RCC_HCLK_DIV4) || ((__PCLK__) == RCC_HCLK_DIV8) || \ ((__PCLK__) == RCC_HCLK_DIV16)) #define IS_RCC_RTCCLKSOURCE(__SOURCE__) (((__SOURCE__) == RCC_RTCCLKSOURCE_NO_CLK) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_LSE) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_LSI) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV32)) #define IS_RCC_MCO(__MCOX__) ((__MCOX__) == RCC_MCO1) #if defined(RCC_HSI48_SUPPORT) #define IS_RCC_MCO1SOURCE(__SOURCE__) (((__SOURCE__) == RCC_MCO1SOURCE_NOCLOCK) || \ ((__SOURCE__) == RCC_MCO1SOURCE_SYSCLK) || \ ((__SOURCE__) == RCC_MCO1SOURCE_MSI) || \ ((__SOURCE__) == RCC_MCO1SOURCE_HSI) || \ ((__SOURCE__) == RCC_MCO1SOURCE_HSE) || \ ((__SOURCE__) == RCC_MCO1SOURCE_PLLCLK) || \ ((__SOURCE__) == RCC_MCO1SOURCE_LSI) || \ ((__SOURCE__) == RCC_MCO1SOURCE_LSE) || \ ((__SOURCE__) == RCC_MCO1SOURCE_HSI48)) #else #define IS_RCC_MCO1SOURCE(__SOURCE__) (((__SOURCE__) == RCC_MCO1SOURCE_NOCLOCK) || \ ((__SOURCE__) == RCC_MCO1SOURCE_SYSCLK) || \ ((__SOURCE__) == RCC_MCO1SOURCE_MSI) || \ ((__SOURCE__) == RCC_MCO1SOURCE_HSI) || \ ((__SOURCE__) == RCC_MCO1SOURCE_HSE) || \ ((__SOURCE__) == RCC_MCO1SOURCE_PLLCLK) || \ ((__SOURCE__) == RCC_MCO1SOURCE_LSI) || \ ((__SOURCE__) == RCC_MCO1SOURCE_LSE)) #endif /* RCC_HSI48_SUPPORT */ #define IS_RCC_MCODIV(__DIV__) (((__DIV__) == RCC_MCODIV_1) || ((__DIV__) == RCC_MCODIV_2) || \ ((__DIV__) == RCC_MCODIV_4) || ((__DIV__) == RCC_MCODIV_8) || \ ((__DIV__) == RCC_MCODIV_16)) #define IS_RCC_LSE_DRIVE(__DRIVE__) (((__DRIVE__) == RCC_LSEDRIVE_LOW) || \ ((__DRIVE__) == RCC_LSEDRIVE_MEDIUMLOW) || \ ((__DRIVE__) == RCC_LSEDRIVE_MEDIUMHIGH) || \ ((__DRIVE__) == RCC_LSEDRIVE_HIGH)) #define IS_RCC_STOP_WAKEUPCLOCK(__SOURCE__) (((__SOURCE__) == RCC_STOP_WAKEUPCLOCK_MSI) || \ ((__SOURCE__) == RCC_STOP_WAKEUPCLOCK_HSI)) /** * @} */ /* Include RCC HAL Extended module */ #include "stm32l4xx_hal_rcc_ex.h" /* Exported functions --------------------------------------------------------*/ /** @addtogroup RCC_Exported_Functions * @{ */ /** @addtogroup RCC_Exported_Functions_Group1 * @{ */ /* Initialization and de-initialization functions ******************************/ void HAL_RCC_DeInit(void); HAL_StatusTypeDef HAL_RCC_OscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct); HAL_StatusTypeDef HAL_RCC_ClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t FLatency); /** * @} */ /** @addtogroup RCC_Exported_Functions_Group2 * @{ */ /* Peripheral Control functions ************************************************/ void HAL_RCC_MCOConfig(uint32_t RCC_MCOx, uint32_t RCC_MCOSource, uint32_t RCC_MCODiv); void HAL_RCC_EnableCSS(void); uint32_t HAL_RCC_GetSysClockFreq(void); uint32_t HAL_RCC_GetHCLKFreq(void); uint32_t HAL_RCC_GetPCLK1Freq(void); uint32_t HAL_RCC_GetPCLK2Freq(void); void HAL_RCC_GetOscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct); void HAL_RCC_GetClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t *pFLatency); /* CSS NMI IRQ handler */ void HAL_RCC_NMI_IRQHandler(void); /* User Callbacks in non blocking mode (IT mode) */ void HAL_RCC_CSSCallback(void); /** * @} */ /** * @} */ /** * @} */ /** * @} */ #ifdef __cplusplus } #endif #endif /* __STM32L4xx_HAL_RCC_H */ /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/